journal article·2009-04-01

Effect of Fiber Content on Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites

Youssef K. Hamidi, Sudha Dharmavaram, Levent Aktas, M. Cengiz Altan

Publisher page

Abstract

Effect of fiber volume fraction on occurrence, morphology, and spatial distribution of microvoids in resin transfer molded E-glass/epoxy composites is investigated. Three disk-shaped center-gated composite parts containing 8, 12, and 16 layers of randomly-oriented, E-glass fiber perform are molded, yielding 13.5%, 20.5%, and 27.5% fiber volume fractions. Voids are evaluated by microscopic image analysis of the samples obtained along the radius of these disk-shaped composites. The number of voids is found to decrease moderately with increasing fiber content. Void areal density decreased from 10.5 voids/mm2 to 9.5 voids/mm2 as fiber content is increased from 13.5% to 27.5%. Similarly, void volume fraction decreased from 3.1% to 2.5%. Increasing fiber volume fraction from 13.5% to 27.5% is found to lower the contribution of irregularly-shaped voids from 40% of total voids down to 22.4%. Along the radial direction, combined effects of void formation by mechanical entrapment and void mobility are shown to yield a spatially complex void distribution. However, increasing fiber content is observed to affect the void formation mechanisms as more voids are able to move toward the exit vents during molding. These findings are believed to be applicable not only to resin transfer molding but generally to liquid composite molding processes.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Mechanical Behavior of Composites · Composite Material Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Ecole Nationale des Science Appliquées Safi, Université Cadi Ayyad, BP 63, 46000 Safi, Morocco

School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, OK 73019

References (41)

Show source-provided references
1. Vacuum Injection Moulding for Large Structural Applications10.1016/S1359-835X(03)00060-5 ↗
2. Investigation Into Various Methods of Liquid Injection to Achieve Mouldings With Minimum Void Content and Full Wet Out10.1016/S1359-835X(97)00124-3 ↗
3. A Comparison of Physical Properties of Glass Fiber Epoxy Composites Produced by Wet Lay-Up With Autoclave Consolidation and Resin Transfer Moulding10.1016/S1359-835X(98)00055-4 ↗
4. Johnson
5. Resin Transfer Molding of Aerospace Resins - A Review10.1002/pi.4980200506 ↗
6. Voids and Their Effects on the Mechanical Properties of Composites—An Appraisal
7. Effect of Injection Rate and Post-Fill Cure Pressure on Resin Transfer Molded Disks10.1177/0021998302036016244 ↗
8. A Study of the Effects of Convergent Flow Fronts on the Properties of Fiber Reinforced Composites Produced by Resin Transfer Molding10.1016/S1359-835X(97)00041-9 ↗
9. Reduction in Interlaminar Shear Strength by Discrete and Distributed Voids10.1016/0266-3538(95)00128-X ↗
10. Void Effects on the Interlaminar Shear-Strength of Unidirectional Graphite-Fiber-Reinforced Composites10.1177/002199839202601006 ↗
11. A Note on the Effect of Voids Upon the Hygral and Mechanical Properties of AS4/3502 Graphite/Epoxy10.1177/002199838702100306 ↗
12. Quantitative Measurement of Voids Formed During Liquid Impregnation of Nonwoven Multifilament Glass Networks Using an Optical Visualization Technique10.1002/pen.760320504 ↗
13. Effect of Fiber Mat Architecture on Void Formation and Removal in Liquid Composite Molding10.1002/pc.750160507 ↗
14. Micro Scale Flow Behavior and Void Formation Mechanism During Impregnation Through a Unidirectional Stitched Fiberglass Mat10.1002/pen.760351006 ↗
15. Modeling of Void Formation and Removal in Liquid Composite Molding. Part I: Wettability Analysis10.1002/pc.10594 ↗
16. Experimental Investigation of Flow Induced Microvoids During Impregnation of Unidirectional Stitched Fiberglass Mat10.1002/pc.10601 ↗
17. Influence From Process Parameters on Void Formation in Resin Transfer Molding10.1002/pc.750150105 ↗
18. Resin Transfer Molding Process (RTM) of a High Performance Epoxy Resin. II: Effects of Process Variables on the Physical, Static and Dynamic Mechanical Behavior10.1002/pen.11221 ↗
19. Darcy · 306
20. Effect of Preform Thickness and Volume Fraction on Injection Pressure and Mechanical Properties of Resin Transfer Molded Composites10.1177/0021998304040562 ↗
21. Dry Spot Formation and Changes in Liquid Composite Molding: II Modeling and Simulation10.1177/002199839603001304 ↗
22. Formation of Microvoids During Resin-Transfer Molding Process10.1016/S0266-3538(00)00036-1 ↗
23. Three-Dimensional Features of Void Morphology in Resin Transfer Molded Composites10.1016/j.compscitech.2005.01.001 ↗
24. Formation of Microscopic Voids in Resin Transfer Molded Composites10.1115/1.1789958 ↗
25. Porosity Reduction in the High-Speed Processing of Glass Fiber Composites by Resin Transfer Molding (RTM)10.1177/0021998304038649 ↗
26. Spatial Variation of Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites10.1023/B:JMSL.0000005428.88229.5b ↗
27. Numerical Simulation of Void Formation in LCM10.1016/S1359-835X(03)00055-1 ↗
28. Tow Impregnation Model and Void Formation Mechanisms During RTM10.1177/002199839803200302 ↗
29. Study on Void Formation in Resin Transfer Molding10.1002/pen.10318 ↗
30. Experimental Characterization of Autoclave-Cured Glass-Epoxy Composite Laminates: Cure Cycle Effects Upon Thickness, Void Content and Related Phenomena10.1002/pc.10282 ↗
31. Modeling Preform Impregnation and Void Formation in Resin Transfer Molding of Unidirectional Composites
32. Void Formation in RTM10.1177/073168449301201207 ↗
33. Void Content, Density and Weight Reduction Studies on Short Bamboo Fiber-Epoxy Composites10.1177/0731684404029326 ↗
34. Void Minimization in the Manufacture of Carbon Fiber Composites by Resin Transfer Molding
35. Ghiorse, S. R. , 1991, “A Comparison of Void Measurement Methods for Carbon/Epoxy Composites,” U.S. Army Materials Technology Laboratory, Report No. MTL TR 91-13.
36. Void Content Measurements in Thermoplastic Composite Materials Through Image Analysis From Optical Micrographs10.1515/SECM.2002.10.2.77 ↗
37. Shih, C. -H. , 2000, “Liquid Composite Molding of Tackified Fiber Reinforcement: Preforming and Void Removal,” Ph.D. thesis, Ohio State University, Columbus, OH.
38. Accuracy of a Volume Fraction Measurement Using Areal Image Analysis10.1520/JTE12558J ↗
39. Morphology Analysis of Microvoids in SMC: Aging Effects10.1016/S1359-835X(98)00070-0 ↗
40. A Comparison Between Voids in RTM and Prepreg Carbon/Epoxy Laminates
41. The Role of Voids in Reducing the Interlaminar Shear Strength in RTM Laminates