Comparative Abrasive Wear Study of HVOF Coatings Obtained by Spraying WC-17Co Microcrystalline and Duplex Near-Nanocrystalline Cermet Powders
Source abstract
Abstract
High velocity oxy-fuel spraying was used to develop a near-nanocrystalline coating from a duplex Co coated WC-17Co powder feedstock. A microstructural and mechanical property characterization of the coating with a similar microcrystalline coating of the same composition was made. X-ray diffraction analysis showed less decarburization of the nanocrystalline coating and a more homogeneous coating structure than the microcrystalline coating produced under the same spraying conditions. The mechanical assessment of the coatings was performed using microhardness and indentation fracture toughness measurements. The abrasive wear resistance was determined using the ASTM G65-04 dry-sand rubber wheel test. The results showed that the hardness of the near-nanocrystalline coating was 25% greater than that of the microcrystalline coating and a sixfold increase in the abrasive wear resistance was also recorded for the near-nanocrystalline coating. Examination of the worn surfaces using atomic force microscopy after abrasive testing showed a smoother surface roughness in the near-nanocrystalline coating than that of the microcrystalline coating surface. The increase in fracture toughness of the near-nanocrystalline coating prevented brittle fracture of the coating surface.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Diamond and Carbon-based Materials Research · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical and Manufacturing Engineering, University of Calgary, 2500 University Drive NW, Calgary, Alberta, T2N 1N4, Canada
References (16)
Show source-provided references
1. The Battle With Abrasion in Oil Sand Mining
2. Nanostructured Composite Coatings for Oil Sands Applications10.1179/174329409X439050 ↗
3. Development of Wear Resistant Nanostructured Duplex Coatings by High Velocity Oxy-Fuel Process for Use in Oil Sands Industry10.1166/jnn.2009.M52 ↗
4. Abrasive Wear Behaviour of Conventional and Nanocomposite HVOF-Sprayed WC-Co Coatings10.1016/S0043-1648(99)00032-0 ↗
5. The Enhancement of the Properties of WC-Co HVOF Coatings Through the Use of Nanostructured and Microstructured Feedstock Powders10.1016/j.surfcoat.2006.01.041 ↗
6. A Review on Nanostructured WC-Co Coatings10.1016/S0257-8972(02)00141-X ↗
7. Synthesis, Sintering, and Mechanical Properties of Nanocrystalline Cemented Tungsten Carbide—A Review10.1016/j.ijrmhm.2008.07.011 ↗
8. Nanomaterial Advantage10.1038/419887a ↗
9. The Corrosion and Wear Performance of Microcrystalline WC-10Co-4Cr and Near-Nanocrystalline WC-17Co High Velocity Oxy-Fuel Sprayed Coatings on Steel Substrate10.1007/s11661-010-0296-1 ↗
10. Near-Nanostructured WC-18 pct Co Coatings With Low Amounts of Non-WC Carbide Phase: Part I. Synthesis and Characterization10.1007/s11661-002-0013-9 ↗
11. The Effects of Fuel Chemistry and Feedstock Powder Structure on the Mechanical and Tribological Properties of HVOF Thermal-Sprayed WC-Co Coatings With Very Fine Structures10.1016/S0257-8972(03)00242-1 ↗
12. Sliding and Abrasive Wear Resistance of Thermal Sprayed WC-Co Coatings10.1361/105996301770349583 ↗
13. Low and High Temperature Hardness of WC-6 wt%Co Alloys10.1016/S0263-4368(97)81231-0 ↗
14. Microstructure, Hardness and Toughness of Nanostructured and Conventional WC-Co Composites10.1016/S0965-9773(98)00123-8 ↗
15. Study of Nanostructured WC-Co Coatings10.1016/0263-4368(95)92675-A ↗
16. Investigation of Hip-Sintering of Nanocrystalline WC/Co Powder