On the Determination of Material Creep Constants Using Miniature Creep Test Specimens
Source abstract
Abstract
Full size creep test specimens, i.e., conventional uniaxial creep test specimen and Bridgman notch specimens are usually used to determine the full set of material constants for any creep model. However, in many situations, sufficient material is not available for theses specimens to be manufactured from it. Therefore, small creep test specimens have been introduced and used to determine (i) creep constants and (ii) the remaining life time for engineering components. Two commonly used small creep specimen types, i.e., the impression and the small ring creep tests, are used in this paper to determine the steady state creep constants. However, these specimen types are limited for use in determining the secondary creep properties, i.e., they are unable to determine the full set of material creep constants for creep damage models. In this paper the recently developed small two-bar creep test specimen and the newly developed small notched specimen test are described and used to determine a full set of material constants for Kachanov and Liu-Murakami creep damage models. The small notched specimen manufacturing, loading and testing procedures are described in this paper. P91 steel at 600 °C and (Bar-257) P91 steel at 650 °C have been used to compare the material constants obtained from the small two-bar and the small notched creep test specimens with those obtained from the conventional uniaxial creep test specimens and Bridgman notch specimens. The results show remarkably good agreement between the two sets of results.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, Nottingham NG7 2RD, UK
Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, Nottingham NG7 2RD, UK e-mail:
References (33)
Show source-provided references
1. Emissions From Power Plants Fueled by Peat, Coal, Natural Gas, and Oil10.1016/0048-9697(86)90254-8 ↗
2. Techno-Economic Evaluation of Advanced IGCC Lignite Coal Fuelled Power Plants With CO2 Capture10.1016/j.fuel.2009.04.019 ↗
3. High Efficiency Coal Fueled Power Generation
4. The Evaluation of Weldment Creep Strength Reduction Factors by Experimental and Numerical Simulations10.1016/0308-0161(94)90039-6 ↗
5. Determination of Creep and Damage Properties for P92 at 675 °C10.1177/0309324711413012 ↗
6. Creep Properties and Failure Assessment of New and Fully Repaired P91 Pipe Welds at 923 K
7. Creep Behaviour of Miniature Disc Specimens of Low Alloy Steel
8. Analysis of the Impression Creep Test Method Using a Rectangular Indenter for Determining the Creep Properties in Welds10.1016/0020-7403(95)00112-3 ↗
9. A Novel, High-Sensitivity, Small Specimen Creep Test10.1243/03093247JSA502 ↗
10. Interpretation of Small Ring Creep Tests Data10.1177/0309324712468820 ↗
11. Impression Creep and Other Localized Tests
12. Impression Creep Behavior of 316LN Stainless Steel
13. Creep of a TiAl Alloy: A Comparison of Indentation and Tensile Testing
14. Hyde, T. H., Becker, A. A., Sun, W., Yaghi, A., Williams, J. A., and Concari, S., 2006, “Determination of Creep Properties for P91 Weldment Materials at 625 °C,” 5th International Conference on Mechanics and Materials in Design, Porto, Portugal, July 24–26, J. F. Silva Gomes and S. A. Meguid, eds., INEGI, Balio, Portugal, pp. 165–166.
15. Hyde, T. H., Ali, B. S. M., and Sun, W., 2012, “A Small Creep Test Specimen for Use in Determining Uniaxial Creep Rupture Data,” 2nd International Conference on Determination of Mechanical Properties of Materials by Small Punch and Other Miniature Testing Techniques, Ostrava, Czech Republic, October 2–4.
16. Analysis and Design of a Small, Two-Bar Creep Test Specimen
17. Hyde, C. J., Sun, W., and Hyde, T. H., 2012, “Small Ring Specimen Creep Testing of a Nickel-Based Superalloy,” 2nd International Conference on Determination of Mechanical Properties of Materials by Small Punch and Other Miniature Testing Techniques, Ostrava, Czech Republic, October 2–4.
18. Some Considerations on Specimen Types for Small Sample Creep Tests10.3184/096034010X12801645220736 ↗
19. 1995
20. Sun, W., Hyde, T. H., and Brett, S. J., 2012, “Use of Impression Creep Test Method for Determining Minimum Creep Strain Rate Data,” 2nd International Conference on Determination of Mechanical Properties of Materials by Small Punch and Other Miniature Testing Techniques, Ostrava, Czech Republic, October 2–4.
21. A Creep Life Assessment Method for Boiler Pipes Using Small Punch Creep Test10.1016/j.ijpvp.2009.04.005 ↗
22. On the Interpretation of Results From Small Punch Creep Tests10.1243/03093247JSA592 ↗
23. Determination of Creep Properties From Small Punch Test
24. Effect of Geometric Factors and Processing Parameters on Plastic Damage of SUS304 Stainless Steel by Small Punch Test10.1016/j.matdes.2012.05.029 ↗
25. Determination of Creep Property of 1.25Cr0.5Mo Pearlitic Steels by Small Punch Test10.1016/j.engfailanal.2012.10.004 ↗
26. Damage Mechanics Based Predictions of Creep Crack Growth in 316 Stainless Steel10.1016/j.engfracmech.2010.06.011 ↗
27. Damage Localization of Conventional Creep Damage Models and Proposition of a New Model for Creep Damage Analysis10.1299/jsmea.41.57 ↗
28. Small Two-Bar Specimen Creep Testing of (Bar-257) P91 Steel at 650 °C
29. Testing and Modelling of Creep Crack Growth in Compact Tension Specimens From a P91 Weld at 650 °C10.1016/j.engfracmech.2010.03.043 ↗
30. Time of the Fracture Process Under Creep Conditions
31. Hyde, C. J., 2010, “Thermo-Mechanical Fatigue and Creep of High Temperature Materials,” Ph.D. thesis, University of Nottingham, Nottingham, UK.
32. 2010
33. Impression Creep Technique: An Overview