journal article·2023-10-01

Studies on the Effect of Substrate Preheating, Interlayer Dwell, and Heat Treatment on Microstructure, Residual Stress, and Mechanical Properties of IN625 Superalloy Built by Direct Metal Deposition

K. Mohsin Khan, Thella Babu Rao, B. N. Manjunath, K. Abhinav, A. R. Vinod, Raffi Mohammed

Publisher page

Abstract

Abstract In this investigation, IN625 alloy samples were processed by the directed energy deposition (DED) approach under various metal deposition strategies such as substrate preheating, interlayer dwell and with combined substrate preheating, interlayer dwell, as well as postheat treatment. The processed sample’s microstructural characteristics, residual stress, microhardness, and tensile properties are assessed in comparison to the manufacturing strategies. Rapid heat dissipation caused finer microstructure near the substrate. There is a growth of columnar grain structure epitaxially in the build direction. The progressive microstructure change seen in the build direction across the cross section was due to the gradual rise of heat accumulation between subsequent layers. The interdendritic zones contained Laves phases. Laves phases have a high Nb, Mo, as well as Si content, according to the energy-dispersive spectroscope (EDS) spectrum. The field emission scanning microscopy (FESEM) microstructural morphology of the deposited samples after their postheat treatment has shown a new microstructure with the combination of equiaxed (recrystallized) and columnar dendritic structure with the reconstruction of columnar dendritic solidification microstructure into equiaxed grains. Heat treatment caused the Laves phases to dissolve in the matrix of IN625 alloy, which led to the precipitation of nanometric γ″ phases. The deposition strategies with substrate preheating significantly decreased the residual stress with moderately improved mechanical properties. The combination of substrate preheating, interlayer dwell, and postheat treatment has shown an outstanding reduction of residual stress along with a remarkable improvement in tensile strength with the retainment of an equivalent ductility compared with other strategies.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

National Institute of Technology Andhra Pradesh Department of Mechanical Engineering, , Tadepalligudem, West Godavari 534101, Andhra Pradesh , India

Central Manufacturing Technology Institute , Tumkur Road, Bangalore 560022, Karnataka , India

National Institute of Technology Andhra Pradesh Department of Metallurgical and Materials Engineering, , Tadepalligudem, West Godavari 534101, Andhra Pradesh , India

References (59)

Show source-provided references
1. Compositionally Graded Specimen Made by Laser Additive Manufacturing as a High-Throughput Method to Study Radiation Damages and Irradiation-Assisted Stress Corrosion Cracking10.1016/j.jnucmat.2021.153493 ↗
2. Robust Metal Additive Manufacturing Process Selection and Development for Aerospace Components10.1007/s11665-022-06850-0 ↗
3. Additive Manufacturing of Soft Magnets for Electrical Machines—A Review10.1016/j.mtphys.2020.100255 ↗
4. State of the Art of Additively Manufactured Electromagnetic Materials for Topology Optimized Electrical Machines10.1016/j.addma.2022.102778 ↗
5. Comprehensive Review on Various Additive Manufacturing Techniques and Its Implementation in Electronic Devices10.1016/j.jmsy.2022.01.002 ↗
6. Powder-Based Laser Hybrid Additive Manufacturing of Metals: A Review10.1007/s00170-021-06855-4 ↗
7. Invited Review Article: Metal-Additive Manufacturing—Modeling Strategies for Application-Optimized Designs10.1016/j.addma.2018.06.024 ↗
8. Metal Additive Manufacturing: A Review10.1007/s11665-014-0958-z ↗
9. A Critical Review on Additive Manufacturing of Ti-6Al-4 V Alloy: Microstructure and Mechanical Properties10.1016/j.jmrt.2022.04.055 ↗
10. Characteristics of Bi-Metallic Interfaces Formed During Direct Energy Deposition Additive Manufacturing Processing10.1007/s11663-019-01612-1 ↗
11. Laser Powder Deposition10.1108/13552540910979785 ↗
12. Mater. Sci. Eng.: A · 257 · 17910.1016/j.msea.2010.08.034 ↗
13. Laser Metal Deposition of Inconel 625: Microstructure and Mechanical Properties10.2351/1.4757717 ↗
14. Effects of Substrate Preheating on the Thin-Wall Part Built by Laser Metal Deposition Shaping10.1016/j.apsusc.2014.08.113 ↗
15. Effect of Substrate Preheating by Induction Heater on Direct Energy Deposition of AISI M4 Powder10.1016/j.msea.2016.11.029 ↗
16. Residual Stress in Additive Manufactured Nickel Alloy 625 Parts10.1115/1.4039063 ↗
17. An Overview of Direct Laser Deposition for Additive Manufacturing; Part II: Mechanical Behavior, Process Parameter Optimization and Control10.1016/j.addma.2015.07.002 ↗
18. Closed-Loop Control of Microstructure and Mechanical Properties in Additive Manufacturing by Directed Energy Deposition10.1016/j.msea.2020.140483 ↗
19. Effects of Process Time Interval and Heat Treatment on the Mechanical and Microstructural Properties of Direct Laser Deposited 316L Stainless Steel10.1016/j.msea.2015.07.056 ↗
20. The Effect of Different Scanning Strategies on Microstructural Evolution to 24CrNiMo Alloy Steel During Direct Laser Deposition10.1016/j.msea.2019.138557 ↗
21. Evolution of Solidification Microstructure and Dynamic Recrystallisation of Inconel 625 During Laser Solid Forming Process10.1007/s10853-018-2701-x ↗
22. Effect of Ti Addition on Cracking and Microhardness of Inconel 625 During the Laser Solid Forming Processing10.1016/j.jallcom.2017.03.355 ↗
23. The Influence of Laves Phases on the High-Cycle Fatigue Behavior of Laser Additive Manufactured Inconel 71810.1016/j.msea.2017.03.098 ↗
24. Long Fatigue Crack Propagation Behavior of Inconel 625 Processed by Laser Powder bed Fusion: Influence of Build Orientation and Post-Processing Conditions10.1016/j.ijfatigue.2018.07.008 ↗
25. Residual Stress Mapping in Inconel 625 Fabricated Through Additive Manufacturing: Method for Neutron Diffraction Measurements to Validate Thermomechanical Model Predictions10.1016/j.matdes.2016.10.003 ↗
26. Influence of Heat Treatments on the Microstructure and Mechanical Properties of Inconel 625 Fabricated by Directed Energy Deposition10.1016/j.msea.2021.141309 ↗
27. Effect of Heat Treatment on Microstructure and Mechanical Properties of Inconel 625 Alloy Fabricated by Pulsed Plasma arc Deposition10.1016/j.phpro.2013.11.010 ↗
28. Influence of Heat Treatments on Microstructure Evolution and Mechanical Properties of Inconel 625 Processed by Laser Powder Bed Fusion10.1016/j.msea.2018.05.044 ↗
29. Effect of Heat Treatment on the Microstructural Evolution and Mechanical Properties of GH4099 Additive-Manufactured by Directed Energy Deposition10.1016/j.jallcom.2019.05.348 ↗
30. Microstructural Evolution and Mechanical Properties of Selective Laser Melted a Nickel-Based Superalloy After Post Treatment10.1016/j.msea.2020.139649 ↗
31. Correlation Between Residual Stresses and the Tribological Behaviour of Inconel 625 Coatings10.1016/j.surfcoat.2021.127288 ↗
32. Directed Energy Deposition of AlSi10Mg: Single Track Nonscalability and Bulk Properties10.1016/j.matdes.2020.108847 ↗
33. Laser Aided Direct Metal Deposition of Inconel 625 Superalloy: Microstructural Evolution and Thermal Stability10.1016/j.msea.2009.01.009 ↗
34. Influence of Interlayer Dwell Time on the Microstructure of Inconel 718 Laser Cladded Components10.1016/j.optlastec.2020.106218 ↗
35. Deposition of Ti–6Al–4 V Using Laser and Wire, Part II: Hardness and Dimensions of Single Beads10.1016/j.surfcoat.2011.07.094 ↗
36. Thermal Behavior and Microstructural Evolution During Laser Deposition With Laser-Engineered Net Shaping: Part I. Numerical Calculations10.1007/s11661-008-9557-7 ↗
37. Additive Manufacturing of Metallic Components—Process, Structure and Properties10.1016/j.pmatsci.2017.10.001 ↗
38. Microstructure and Yield Strength of SLM-Fabricated CM247LC Ni-Superalloy10.1016/j.actamat.2017.02.007 ↗
39. Effect of Heat Treatment on Microstructure and Oxidation Properties of Inconel 625 Processed by LPBF10.1016/j.jallcom.2020.156418 ↗
40. Microstructure and Mechanical Properties of Inconel 625 Superalloy10.1016/S0022-3115(00)00723-6 ↗
41. Fracture Analysis of Laser Beam Welded Superalloys Inconel 718 and 625 Using the FITNET Procedure10.1016/j.ijpvp.2008.02.004 ↗
42. Heat Treatment Effects on Inconel 625 Components Fabricated by Wire + Arc Additive Manufacturing (WAAM)—Part 1: Microstructural Characterization10.1007/s00170-019-03828-6 ↗
43. Effect of Heat Treatment and Hot Isostatic Pressing on the Microstructure and Mechanical Properties of Inconel 625 Alloy Processed by Laser Powder Bed Fusion10.1016/j.msea.2017.02.038 ↗
44. Elevated Temperature Mechanical Behavior of IN625 Alloy Processed by Laser Powder-Bed Fusion10.1016/j.msea.2017.06.045 ↗
45. The Role of Texturing and Microstructure Evolution on the Tensile Behavior of Heat-Treated Inconel 625 Produced via Laser Powder Bed Fusion10.1016/j.msea.2019.138500 ↗
46. Heat Treatments Design for Superior High-Temperature Tensile Properties of Alloy 625 Produced by Selective Laser Melting10.1016/j.msea.2020.139720 ↗
47. Microstructure and Tensile Properties of Superalloy IN100 Fabricated by Micro-Laser Aided Additive Manufacturing10.1016/j.matdes.2014.04.020 ↗
48. Characterization of Microstructures in Inconel 625 Using X-Ray Diffraction Peak Broadening and Lattice Parameter Measurements10.1016/j.scriptamat.2004.03.017 ↗
49. Three-Dimensional Phase-Field Simulation of γ″ Precipitation Kinetics in Inconel 625 During Heat Treatment10.1016/j.commatsci.2020.110123 ↗
50. Investigation of Dissolution Behavior of Laves Phase in Inconel 718 Fabricated by Laser Directed Energy Deposition10.1016/j.addma.2020.101055 ↗
51. Effects of Heat Treatment on Microstructure and Mechanical Properties of Inconel 625 Alloy Fabricated by Wire Arc Additive Manufacturing Process10.1016/S1003-6326(20)65439-5 ↗
52. Microstructural Architecture, Microstructures, and Mechanical Properties for a Nickel-Base Superalloy Fabricated by Electron Beam Melting10.1007/s11661-011-0748-2 ↗
53. Formation of the Ni3Nb δ-Phase in Stress-Relieved Inconel 625 Produced via Laser Powder-Bed Fusion Additive Manufacturing10.1007/s11661-017-4304-6 ↗
54. Effect of Location on Microstructure and Mechanical Properties of Additive Layer Manufactured Inconel 625 Using Gas Tungsten Arc Welding10.1016/j.msea.2016.09.015 ↗
55. Microstructure and Residual Stress of Laser Rapid Formed Inconel 718 Nickel-Base Superalloy10.1016/j.optlastec.2010.06.015 ↗
56. Finite Element Analysis and Experimental Validation of Thermal Behavior for Thin-Walled Parts in GMAW-Based Additive Manufacturing With Various Substrate Preheating Temperatures10.1016/j.applthermaleng.2017.07.168 ↗
57. The Role of Substrate Preheating on the Microstructure, Roughness, and Mechanical Performance of AISI 316L Produced by Directed Energy Deposition Additive Manufacturing10.1007/s00170-021-08564-4 ↗
58. Effect of Processing Conditions on the Microstructure, Porosity, and Mechanical Properties of Ti-6Al-4 V Repair Fabricated by Directed Energy Deposition10.1016/j.jmatprotec.2018.08.041 ↗
59. Effects of Substrate Preheating During Direct Energy Deposition on Microstructure, Hardness, Tensile Strength, and Notch Toughness10.1007/s12540-017-7049-2 ↗