journal article·2024-07-01

An Experimental Study on the Accuracy of Cumulative Damage Models in Gear Tooth Bending Fatigue

Gabriel Anichowski, Riley Damm, Ahmet Kahraman, Isaac Hong

Publisher page

Abstract

Abstract Tooth bending fatigue failure is a primary design concern for gear designers in power transmission applications. Fracture of a gear tooth in operation results in overload conditions to adjacent teeth, which cascades into potential failure. Total loss of power transmission usually occurs within seconds of the primary failure. While standard constant stress amplitude fatigue evaluations are common to experimentally determine probabilistic stress–life (PSN) relationships, they do not directly measure the fatigue lives under complex, non-constant amplitude loading scenarios applied to gears in most applications. Various cumulative damage models exist to estimate fatigue life under duty cycle loading, but their accuracy is both material and stress state dependent. Most models are validated under only uniaxial stress states and for limited materials. There is a void of experimental data that would enable the evaluation of the accuracy of cumulative damage models for gear tooth bending fatigue in typical cases of carburized gear steels. This research study conducts a standard fatigue evaluation along with two sets of dual stress amplitude single tooth bending fatigue tests to empirically determine the effects of multi-stage loading. Various cumulative damage fatigue models are then employed to estimate the fatigue lives of the dual stress amplitude specimens, and the accuracy of each model is assessed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · Mechanical Failure Analysis and Simulation · Engineering Diagnostics and Reliability

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

The Ohio State University Gear and Power Transmission Research Laboratory, , Columbus, OH 43210

References (27)

Show source-provided references
1. Cumulative Fatigue Damage and Life Prediction Theories: A Survey of the State of the Art for Homogeneous Materials10.1016/S0142-1123(97)00081-9 ↗
2. An Experimental Investigation of Bending Fatigue Initiation and Propagation Lives10.1115/1.1370496 ↗
3. Manson · 196710.1520/STP47237S ↗
4. Practical Implementation of the Double Linear Damage Rule and Damage Curve Approach for Treating Cumulative Fatigue Damage10.1007/BF00053519 ↗
5. Bending Fatigue Investigation Under Variable Load Conditions on Case Carburized Gears
6. Cumulative Damage and Life Prediction Models for High-Cycle Fatigue of Metals: A Review10.3390/met11020204 ↗
7. Cumulative Damage Rule Based on the Knee Point of the S-N Curve10.1115/1.3443383 ↗
8. A Cumulative Damage Theory of Fatigue Failure10.1016/0025-5416(78)90045-9 ↗
9. Cumulative Fatigue Damage: CDM-Based Engineering Rule and Life Prediction Aspect10.1002/srin.201600048 ↗
10. A One-Parameter Nonlinear Fatigue Damage Accumulation Model10.1016/j.ijfatigue.2017.01.039 ↗
11. A Fatigue Driving Stress Approach to Damage and Life Prediction Under Variable Amplitude Loading10.1177/1056789512449638 ↗
12. Nonlinear Fatigue Damage Accumulation and Life Prediction of Metals: A Comparative Study10.1111/ffe.12937 ↗
13. A New Nonlinear Fatigue Damage Model Based Only on S-N Curve Parameters10.1016/j.ijfatigue.2017.06.017 ↗
14. The Exponential Law of Endurance Tests
15. SAE International Surface Vehicle Recommended Practice · 1997
16. An Experimental Evaluation of High-Cycle Gear Tooth Bending Fatigue Lives Under Fully Reversed and Fully Released Loading Conditions With Application to Planetary Gear Sets10.1115/1.4047687 ↗
17. A Rotating Gear Test Methodology for Evaluation of High-Cycle Tooth Bending Fatigue Lives Under Fully Reversed and Fully Released Loading Conditions10.1016/j.ijfatigue.2019.105432 ↗
18. A Comparison of Gear Tooth Bending Fatigue Lives from Single Tooth Bending And Rotating Gear Tests10.1007/s10010-021-00510-w ↗
19. 2016
20. ISO
21. ISO Standard Based Method for Calculating the In-Operation Application Factor KA in Gears Subjected to Variable Working Conditions10.1016/j.ijfatigue.2015.11.014 ↗
22. On Long-Term Fatigue Damage and Reliability Analysis of Gears Under Wind Loads in Offshore Wind Turbine Drivetrains10.1016/j.ijfatigue.2013.11.023 ↗
23. A Method for Obtaining and Analyzing Sensitivity Data10.1080/01621459.1948.10483254 ↗
24. Statistical Approaches Applied to Fatigue Test Data Analysis
25. Accuracy of Fatigue Limits Estimated by the Staircase Method Using Different Evaluation Techniques10.1016/j.ijfatigue.2017.03.030 ↗
26. Fitting of Fatigue Curves With Noncontant Standard Deviation to Data with Runouts10.1520/JTE10700J ↗
27. A Comparison of Maximum Likelihood Models for Fatigue Strength Characterization in Materials Exhibiting a Fatigue Limit10.1016/j.probengmech.2008.06.006 ↗