Effect of Build Geometry and Porosity in Additively Manufactured CuCrZr
Source abstract
Abstract
Abstract The current work presents an understanding of microstructure and mechanical properties as a function of build geometry and build orientation in Cu-Cr-Zr via the laser powder bed fusion (LPBF) technique. Porosity, microstructure, and mechanical properties have been compared in as-printed (AP) and heat-treated (HT) LPBF Cu-Cr-Zr, between cylindrical and cube geometries, along the longitudinal (L) and transverse (T) build orientations. Varying porosity levels were observed that yielded parts with 96–97% relative density in the AP condition. The AP microstructure demonstrated a hierarchical microstructure, comprising grains (2.5–100 μm) with a cellular substructure (400–850 nm) and intracellular nanoscale (20–60 nm) precipitates. Unlike most materials in the AP condition, crystallographic texture was found to be absent; however, very distinct river-like patterns highlighted a novel feature of the LPBF Cu-Cr-Zr. Upon solutionizing and aging, Cr precipitates were seen heterogeneously nucleating along cell boundaries (0.5–1.3 μm), causing up to 45% enhancement in the strength and a 4–5% lower ductility. The yield strength along the transverse orientation was 10–16% higher than that of longitudinal orientation, in both the AP and HT conditions. Fracture surface of the tensile samples exhibited micro-voids, cleavage facets, and unmelted particles. Despite the porosity, overall mechanical properties matched well with those obtained in nearly dense (>99%) samples and the mechanical property debit was less than 10%.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Anatomy and Medical Technology
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Pratt & Whitney, Research and Development Center , Bangalore 560012, Karnataka , India
Indian Institute of Technology Hyderabad Department of Materials Science and Metallurgical Engineering, , Telangana 502285 , India
References (30)
Show source-provided references
1. Copper Alloys for High Heat Flux Structure Applications
2. Comparative Analysis of Copper Alloys for the Heat Sink of Plasma Facing Components in ITER10.1016/S0022-3115(98)00271-2 ↗
3. Materials Challenges for ITER—Current Status and Future Activities10.1016/j.jnucmat.2007.03.017 ↗
4. Comparison of GRCop-84 to Other Cu Alloys With High Thermal Conductivities10.1007/s11665-007-9175-3 ↗
5. Effect of Processing and Heat Treatment on Behavior of Cu-Cr-Zr Alloys to Railway Contact Wire10.1007/BF02586158 ↗
6. Improved Compromise Between the Electrical Conductivity and Hardness of the Thermo-Mechanically Treated CuCrZr Alloy10.1016/j.msea.2018.03.004 ↗
7. Precipitation in a Cu-0, 55 wt% Cr Alloy10.1016/0001-6160(79)90072-5 ↗
8. Structure of Coherent Chromium Precipitates in Aged Copper Alloys10.1016/0036-9748(86)90154-7 ↗
9. Effect of a Small Addition of Zirconium on Hot Ductility of a Cu-Cr Alloy10.1515/ijmr-1988-791011 ↗
10. Effect of Small Alloying Additions on Behaviour of Rapidly Solidified Cu–Cr Alloys10.1179/mst.1990.6.9.892 ↗
11. Microstructure and Properties of a Cu–Cr–Zr Alloy10.1016/S0022-3115(01)00691-2 ↗
12. X-ray Diffraction Line Profile Analysis for Defect Study in Cu-1 wt% Cr-0.1 wt% Zr Alloy10.1016/j.matchar.2004.09.009 ↗
13. Phase Relationships in Cu-Rich Corner of the Cu-Cr-Zr Phase Diagram10.1016/0956-716X(95)00084-9 ↗
14. Analysis of Phases in a Cu–Cr–Zr Alloy10.1016/S1359-6462(02)00353-6 ↗
15. Atomic Scale Investigation of Cr Precipitation in Copper10.1016/j.actamat.2012.01.038 ↗
16. A Metal Additively Manufactured (MAM) Heat Exchanger for Electric Motor Thermal Control on a High-Altitude Solar Aircraft—Experimental Characterisation10.1016/j.tsep.2020.100629 ↗
17. Exploiting Volumetric Effects in Novel Additively Manufactured Open Solar Receivers10.1016/j.solener.2018.09.030 ↗
18. A Fully Developed Flow Thermofluid Model for Topology Optimization of 3D-Printed Air-Cooled Heat Exchangers10.1016/j.applthermaleng.2017.03.030 ↗
19. State-of-the-Art in Heat Exchanger Additive Manufacturing10.1016/j.ijheatmasstransfer.2021.121600 ↗
20. Toyserkani · 202110.1002/9781119210801 ↗
21. Laser Powder Bed Fusion—Materials Issues and Optimized Processing Parameters for Tool Steels, AlSiMg- and CuCrZr-Alloys10.1002/adem.201600667 ↗
22. Effect of Heat Treatments on Microstructure and Properties of CuCrZr Produced by Laser-Powder Bed Fusion10.1016/j.msea.2018.12.017 ↗
23. Additive Manufacturing of CuCr1Zr by Development of a Gas Atomization and Laser Powder Bed Fusion Routine10.1007/s00170-020-04941-7 ↗
24. Additively Manufactured CuCrZr Alloy: Microstructure, Mechanical Properties and Machinability10.1016/j.msea.2021.141528 ↗
25. CuCrZr Processed by Laser Powder Bed Fusion—Processability and Influence of Heat Treatment on Electrical Conductivity, Microstructure and Mechanical Properties10.1111/ffe.13527 ↗
26. CuCrZr Alloy Produced by Laser Powder Bed Fusion: Microstructure, Nanoscale Strengthening Mechanisms, Electrical and Mechanical Properties10.1016/j.msea.2021.141915 ↗
27. Effect of Selective Laser Melting Process Parameters and Aging Heat Treatment on Properties of CuCrZr Alloy10.1088/2053-1591/ab4e2f ↗
28. Mechanical Properties of High-Strength Cu–Cr–Zr Alloy Fabricated by Selective Laser Melting10.3390/ma13215028 ↗
29. Anisotropy and Heterogeneity of Microstructure and Mechanical Properties in Metal Additive Manufacturing: A Critical Review10.1016/j.matdes.2017.11.021 ↗
30. Effects of Defects on Mechanical Properties in Metal Additive Manufacturing: A Review Focusing on X-ray Tomography Insights10.1016/j.matdes.2019.108385 ↗