A Unique Method to Determine Ferrite and Martensite Phase Stress–Strain Curve for Manufacturing Process
Source abstract
Abstract
Abstract Finite element (FE) methods have been extensively used to simulate the effects of material’s microstructure during machining processes. However, determination of the individual microstructure phase stress–strain curves is experimentally intensive and difficult to measure. Furthermore, these curves were also affected by heat treatment processes, chemical composition, and the percentage of individual microstructure phases. The objective of this paper is to develop and validate the Micromechanical Adaptive Iteration Algorithm to calculate the individual ferrite and martensite plastic behavior for dual-phase (DP) steel. This method requires a minimum of three experimental stress–strain curves from the same material with three different martensite volume fractions (Vm). Two of the stress–strain curves with different Vm are required to initialize the iteration algorithm to predict the individual plastic behavior of ferrite and martensite. The third stress–strain curve is used to validate the plastic behavior of individual ferrite and martensite for the given DP steel. Following on from here, the proposed algorithm was validated with two different grades of DP steel with 0.088%C and 0.1%C. Validation results show that the approach has consistent prediction capabilities, and the maximum difference observed between predicted and experimental results was 6.5%. The simulated results also show that the degree of strain partitioning between ferrite and martensite decreases with Vm.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Microstructure and Mechanical Properties of Steels · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
McMaster University Department of Mechanical Engineering, W. Booth School of Engineering Practice and Technology, , 1280 Main Street West, Hamilton, ON L8S 4L7 , Canada
McMaster University Department of Mechanical Engineering, , 1280 Main Street West, Hamilton, ON L8S 4L7 , Canada
Funding
Natural Sciences and Engineering Research Council of Canada
References (29)
Show source-provided references
1. Recent Advances in Modelling of Metal Machining Processes10.1016/j.cirp.2013.05.006 ↗
2. Microstructure-Based FEM Simulation of Metal Cutting10.1016/j.procir.2017.03.336 ↗
3. Influence of Microstructure on Chip Formation When Broaching Ferritic-Pearlitic Steels10.1016/j.procir.2017.03.181 ↗
4. Grain Size and Orientation Effects When Microcutting AISI 1045 Steel10.1016/j.cirp.2007.05.016 ↗
5. A New 3D Multiphase FE Model for Micro Cutting Ferritic-Pearlitic Carbon Steels10.1016/j.cirp.2012.03.075 ↗
6. Prediction of Mechanical Properties of Multi-Phase Steels Based on Stress-Strain Curves10.2355/isijinternational.32.343 ↗
7. Effect of Volume Fraction of Constituent Phases on the Stress-Strain Relationship of Dual Phase Steels10.2355/isijinternational.39.288 ↗
8. Unified Formulation to Predict the Tensile Curves of Steels With Different Microstructures10.4028/<www.scientific.net>/msf.426-432.4525 ↗
9. 3D Micromechanical Modeling of Dual Phase Steels Using the Representative Volume Element Method10.1016/j.mechmat.2016.07.011 ↗
10. A Micromechanical Damage Simulation of Dual Phase Steels Using XFEM10.1016/j.commatsci.2011.10.035 ↗
11. Characterization and Modelling of Failure Initiation in DP Steel10.1016/j.commatsci.2013.04.001 ↗
12. The Influence of Microstructure and Composition on the Plastic Behaviour of Dual-Phase Steels10.1016/j.actamat.2014.04.015 ↗
13. Damage and Fracture of Dual-Phase Steels: Influence of Martensite Volume Fraction10.1016/j.msea.2015.08.073 ↗
14. FEM Modeling of the Flow Curves and Failure Modes of Dual Phase Steels With Different Martensite Volume Fractions Using Actual Microstructure as the Representative Volume10.1016/j.commatsci.2012.07.032 ↗
15. Failure Mechanism and Mode of Ti-6Al-4V Alloy Under Uniaxial Tensile Loading: Experiments and Micromechanical Modeling10.1016/j.msea.2016.09.019 ↗
16. Prediction of Composite Properties From a Representative Volume Element10.1016/0266-3538(95)00141-7 ↗
17. Strain Partition, Uniform Elongation and Fracture Strain in Dual-Phase Steels10.1016/0025-5416(87)90507-6 ↗
18. Strain Localization and Damage in Dual Phase Steels Investigated by Coupled In-Situ Deformation Experiments and Crystal Plasticity Simulations10.1016/j.ijplas.2014.06.004 ↗
19. Local Plastic Strain Evolution in a High Strength Dual-Phase Steel10.1016/j.msea.2010.04.052 ↗
20. Microscopic Deformation Behaviour of Martensitic–Ferritic Dual-Phase Steels10.1179/mst.1986.2.1.28 ↗
21. Correlation Between 2D and 3D Flow Curve Modelling of DP Steels Using a Microstructure-Based RVE Approach10.1016/j.msea.2012.09.046 ↗
22. AME Modelling the Mechanical Behaviour of Steels With Mixed Microstructures
23. The Mechanical Properties of Zero-Carbon Ferrite-Plus-Martensite Structures10.1007/BF02646397 ↗
24. Fonstein · 201510.1007/978-3-319-19165-2 ↗
25. Influence of Martensite Composition and Content on the Properties of Dual Phase Steels10.1007/BF02659924 ↗
26. Effect of Material Inhomogeneity on the Cyclic Plastic Deformation Behavior at the Microstructural Level: Micromechanics-Based Modeling of Dual-Phase Steel10.1088/0965-0393/21/5/055001 ↗
27. Böhm · 1998
28. Digital Image Correlation Studies for Microscopic Strain Distribution and Damage in Dual Phase Steels10.1016/j.scriptamat.2007.01.031 ↗
29. Influence of Martensite Morphology and Its Dispersion on Mechanical Properties and Fracture Mechanisms of Fe-Mn-C Dual Phase Steels10.1179/030634584790419953 ↗