Quantitative Stress Analysis of Recrystallized OFHC Cu Subject to Deformation In Situ
Source abstract
Abstract
Quantitative strain analysis (QSA) provides a means for assessing the orientation-dependent micromechanical stress states in bulk polycrystalline materials. When combined with quantitative texture analysis, it facilitates tracking the evolution of micromechanical states associated with selected texture components for specimens deformed in situ. To demonstrate this ability, a sheet specimen of rolled and recrystallized oxygen-free high conductivity Cu was subject to tensile deformation at APS 1-ID-C. Strain pole figures (SPFs) were measured at a series of applied loads, both below and above the onset of macroscopic yielding. From these data, a lattice strain distribution function (LSDF) was calculated for each applied load. Due to the tensorial nature of the LSDF, the full orientation-dependent stress tensor fields can be calculated unambiguously from the single-crystal elastic moduli. The orientation distribution function (ODF) is used to calculate volume-weighted average stress states over tubular volumes centered on the ⟨100⟩∥[100], ⟨311⟩∥[100], and ⟨111⟩∥[100] fibers—accounting for ≈50% of the total volume—are shown as functions of the applied load along [100]. Corresponding weighted standard deviations are calculated as well. Different multiaxial stress states are observed to develop in the crystal subpopulations despite the uniaxial nature of the applied stress. The evolution of the orientation-dependent elastic strain energy density is also examined. The effects of applying stress bound constraints on the SPF inversion are discussed, as are extensions of QSA to examine defect nucleation and propagation.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · Non-Destructive Testing Techniques · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Engineering Technologies Division, Lawrence Livermore National Laboratory, B141/R1114, L-229, Livermore, CA 94551
Sibley School of Mechanical and Aerospace Engineering, Cornell University, 195 Rhodes Hall, Ithaca, NY 14853
Advanced Photon Source, Argonne National Laboratory, B431/A007, Argonne, IL 60439
References (31)
Show source-provided references
1. An Accelerated Methodology for the Evaluation of Critical Properties in Polyphase Alloys10.1007/s11661-005-0025-3 ↗
2. Synchrotron X-Ray Study of Bulk Lattice Strains in Externally Loaded Cu-Mo Composites10.1007/BF02830344 ↗
3. Simultaneous Measurement of the Strain Tensor of 10 Individual Grains Embedded in an al Tensile Sample
4. The Use of High Energy X-Rays From the Advanced Photon Source to Study Stresses in Materials10.1016/j.msea.2005.02.023 ↗
5. Determination of the Radial Crystallite Microstrain Distribution Within an almg3 Torsion Sample Using Monochromatic Synchrotron Radiation10.1016/j.msea.2005.04.005 ↗
6. Experimental Measurement of Lattice Strain Pole Figures Using Synchrotron X-Rays10.1063/1.2130668 ↗
7. Load Partitioning During Compressive Loading of a Mg∕MgB2 Composite10.1016/j.actamat.2007.01.046 ↗
8. Kocks
9. Chateigner, D. , 2006, “Combined Analysis: Structure-Texture-Microstructure-Phase-Stresses-Reflectivity Determination by X-Rays and Neutron Scattering,” URL: www.ecole.ensicaen.fr/~chateign/texture/combined.pdf.
10. A Direct Method for the Determination of the Mean Orientation-Dependent Elastic Strains and Stresses in Polycrystalline Materials From Strain Pole Figures10.1107/S0021889806009873 ↗
11. Nye
12. Some Basic Concepts of Texture Analysis and Comparison of Three Methods to Calculate Orientation Distributions From Pole Figures10.1107/S0021889888000275 ↗
13. Anisotropy and Symmetry
14. Strain-Function Method for the Direct Evaluation of Intergranular Strains and Stresses10.1002/(SICI)1521-396X(200002)177:2<401::AID-PSSA401>3.0.CO;2-I ↗
15. A Novel Method for Constructing the Mean Field of Grain Orientation-Dependent Residual Stress10.1080/09500830010017088 ↗
16. Bunge
17. Description of Crystalline Orientation in Polycrystalline Materials III: General Solution to Pole Figure Inversion10.1063/1.1714396 ↗
18. Bunge
19. Determination of the Orientation Distribution From Pole Figure Data
20. A Novel Optimization-Based Pole-Figure Inversion Method: Comparison With Wimv and Maximum Entropy Methods10.1107/S002188980602468X ↗
21. Miller, M. P., Park, J. S., Dawson, P. R., and Han, T. S., 2007, “Measuring and Modeling Distributions of Stress State in Deforming Polycrystals,” Acta Mater.1359-6454 (to be published).
22. Maud: A Rietveld Analysis Program Designed for the Internet and Experiment Integration10.1107/S0108767300021954 ↗
23. Quantitative Rietveld Texture Analysis of Zirconium From Single Synchrotron Diffraction Images10.1107/S0021889805006059 ↗
24. Texture Analysis From Synchrotron Diffraction Images With the Rietveld Method: Dinosaur Tendon and Salmon Scale10.1107/S090904950500138X ↗
25. Orientation Distribution: Representation and Determination
26. Kelly10.1002/9781119961468 ↗
27. Texture Analysis With the New Hippo Tof Diffractometer10.1016/j.nima.2003.05.001 ↗
28. Strain Field and Scattered Intensity Profiling With Energy Dispersive X-Ray Scattering10.1063/1.1483373 ↗
29. A System for Measuring Crystal Level Stresses in Deforming Polycrystals
30. Bernier, J. V. , 2006, “On the Use of Diffraction in Quantifying the Structure and Micromechanical State of Polycrystalline Materials,” Ph.D. thesis, Cornell University.
31. Lattice Strain Partitioning in a Two-Phase Alloy and Its Redistribution Upon Yielding10.1016/j.msea.2005.05.095 ↗