journal article·2019-07-01

Mechanical Characterization and Modeling of Direct Metal Laser Sintered Stainless Steel GP1

Sanna F. Siddiqui, Abiodun A. Fasoro, Calvin Cole, Ali P. Gordon

Publisher page

Abstract

The additive manufacturing (AM) process is unique in that it can facilitate anisotropy because of the layer-by-layer deposition technique intrinsic to this process. In order to develop a component for a desired application, it is necessary to understand the mechanics that facilitate this material behavior. This study investigates how build orientation affects the mechanical performance of as-built direct metal laser sintered (DMLS) stainless steel (SS) GP1 (also referred to as 17-4PH) through strain-controlled monotonic tension and completely reversed low-cycle fatigue (LCF) testing. The anisotropic behavior of DMLS SS GP1 is assessed for samples built along the horizontal plane. Fracture surfaces were found to exhibit ductile responses that were consistent with the σ–ε curves. Constitutive models (i.e., Ramberg–Osgood, Hahn) based upon linear elasticity and nonlinear plasticity are presented and used to simulate the monotonic discontinuous stress–strain yielding response of this material, which are found to be in agreement with the experimental data. A collection of low-cycle fatigue tests reveals initial strain hardening to stabilization, followed by softening to fracture. Tensile and fatigue material constants determined from experimental findings are also presented in this study. Plasticity effects on the life of varying build orientations are explored.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical and Aerospace Engineering, University of Central Florida, Orlando, FL 32816 e-mails: ;

Department of Manufacturing Engineering, Central State University, Wilberforce, OH 45384 e-mail:

Department of Mechanical and Aerospace Engineering, University of Central Florida, Orlando, FL 32816 e-mail:

Funding

Division of Graduate Education

References (26)

Show source-provided references
1. Anisotropy and Heterogeneity of Microstructure and Mechanical Properties in Metal Additive Manufacturing: A Critical Review10.1016/j.matdes.2017.11.021 ↗
2. EOS StainlessSteel GP1 for EOSINT M 270 Material Data Sheet
3. Additive Manufacturing of 17-4PH Stainless Steel: Post-Processing Heat Treatment to Achieve Uniform Reproducible Microstructure10.1007/s11837-015-1754-4 ↗
4. Metastable Austenite in 17-4 Precipitation-Hardening Stainless Steel Produced by Selective Laser Melting10.1002/adem.200900259 ↗
5. Mechanical Properties of Austenitic Stainless Steel Made by Additive Manufacturing10.6028/jres.119.015 ↗
6. Fatigue Behavior of Selective Laser Melted 17-4PH Stainless Steel
7. Mechanical Behavior of Additive Manufactured, Powder-Bed Laser-Fused Materials10.1016/j.msea.2015.10.068 ↗
8. Modeling the Influence of Build Orientation on the Monontonic and Cyclic Response of Additively Manufactured Stainless Steel GP1/17-4PH
9. Effects of Building Orientation and Heat Treatment on Fatigue Behavior of Selective Laser Melted 17-4 PH Stainless Steel10.1016/j.ijfatigue.2016.03.014 ↗
10. The Effect of Surface Finish on Tensile Behavior of Additively Manufactured Tensile Bars10.1007/s10853-015-9702-9 ↗
11. Torsional Response of Additively Manufactured Steel Under Monotonic and Cyclic Conditions
12. Fatigue Analysis in Selective Laser Melting: Review and Investigation of Thin-Walled Actuator Housings
13. Standard Test Methods for Tension Testing of Metallic Materials10.1520/E0008_E0008M-15A ↗
14. Siddiqui, S.F. 2018, “Characterization of Anisotropic Mechanical Performance of As-Built Additively Manufactured Metals,” Ph.D. dissertation, University of Central Florida, pp. 1–266.
15. Kelley, P. F.Jr. , 2016, “Fatigue Behavior of Direct Metal Laser Sintered (DMLS) Inconel 718,” Master's thesis, Tufts University, Medford, MA.10.1115/IMECE2015-50937 ↗
16. Chapter 14: Selective Laser Melting (SLM) of Ni-based Superalloys – A Mechanics of Materials Review10.1201/9781315119106-14 ↗
17. EOS M-Solutions, 06/201 3, “Laser Sintering System EOSINT M 280 for the Production of Tooling Inserts, Prototype Parts and End Products Directly in Metal,” Krailing/Munich, Germany.
18. Product Data Sheet 17-4PH Stainless Steel
19. Standard Test Method for Creep-Fatigue Testing10.1520/E2714 ↗
20. Microstructures and Properties of 17-4PH Stainless Steel Fabricated by Selective Laser Melting10.1016/S2238-7854(12)70029-7 ↗
21. Revealing Martensitic Transformation and α/β Interface Evolution in Electron Beam Melting Three-Dimensional-Printed Ti-6Al-4V10.1038/srep26039 ↗
22. Mechanical Properties and Microstructural Characterization of Selective Laser Melted 17-4PH Stainless Steel10.1108/RPJ-12-2015-0192 ↗
23. A Model for Yielding With Special Reference to the Yield-Point Phenomena of Iron and Related bcc Metals10.1016/0001-6160(62)90041-X ↗
24. Elastic-Plastic Analysis of the Yield Process in Mild Steel10.1016/0022-5096(76)90002-8 ↗
25. Characterization of the Tensile Behavior of a Metallic Fiber Woven Structure10.1177/0040517511398944 ↗
26. Approach for Stabilized Peak/Valley Stress Modeling of Non-Isothermal Fatigue of a DS Ni-Base Superalloy10.1520/MPC20130070 ↗