Influence of Heat Treatment on the Mechanical Properties and Damage Development in a SiC/Ti-15-3 MMC
Source abstract
Abstract
Titanium alloys are commonly heat-treated to meet specific design requirements. In an effort to possibly create a better composite, the influence of heat treatments on the damage evolution and strength of a SiC/Ti-15-3 metal matrix composite (MMC) was studied. Heat treatments of 450°C and 700°C for 24 hours were performed on axial and transverse unidirectional specimens. These specimens, in addition to specimens in the as-received condition, were tested under nonproportional loading paths and then microstructurally analyzed to determine the induced damage. The axial composite with the 450°C heat treatment showed the highest elastic modulus and the lowest stiffness reduction than the other heat treatment conditions. The transverse composite in the as-received condition showed the highest room temperature elastic modulus and the lowest stiffness reduction compared with other heat treatment conditions. Typical damage modes of Ti MMC’s, such as fiber/matrix debonding and matrix microcracking, were seen in all heat treatments. A micromechanics model based on the Mori-Tanaka averaging scheme was implemented to simulate the effects of micro-cracking induced damage on composite stiffness reduction. [S0094-4289(00)01101-4]
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties · Composite Material Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Aerospace Engineering, Center for Mechanics of Composites, Texas A&M University, College Station, TX 77843-3141
References (17)
Show source-provided references
1. Johnson, W. S., 1992, NASA Technical Memorandum 107597, Lewis Research Center.
2. Lissenden Herakovich, C. T., and Pindera, M. J., 1995, “Response of SiC/Ti under Combined Loading Part I: Theory and Experiment for Imperfect Bonding,” J. Compos. Mater., 29, No. 2, pp. 130–155.10.1177/002199839502900201 ↗
3. Majumdar, B. S., and Newaz, G. M., 1992a, 1992b, 1993, NASA Contractor Report 189095, 189096, 191181, Lewis Research Center.
4. Lagoudas, D. C., Ma, X., Miller, D. A., and Allen, D. H., 1995, “Modeling of Oxidation in Metal Matrix Composites,” Int. J. Eng. Sci., 33, pp. 2327–2343.10.1016/0020-7225(95)00073-7 ↗
5. Newaz, G. M., Majumdar, B. S., and Brust, F. W., 1992, “Thermal Cycling Response of Quasi-Isotropic Metal Matrix Composites,” ASME J. Eng. Mater. Technol., 114, pp. 156–161.10.1115/1.2904155 ↗
6. Johnson, W. S., Lubowinski, S. J., and Highsmith, A. L., 1990, “Mechanical Characterization of Unnotched SCS-6/Ti-15-3 Metal Matrix Composites at Room Temperature,” Thermal and Mechanical Behavior of Metal Matrix and Ceramic Matrix Composites, ASTM STP 1080, J. M. Kennedy et al., eds., ASTM, Philadelphia, PA, pp. 193–218.10.1520/STP25401S ↗
7. Lerch, B. A., Gabb, T. P., and MacKay, R. A., 1990, “Heat Treatment Study of the SiC/Ti-15-3 Composite System,” NASA TP 2970.
8. Wolfenden, A., Hall, K. D., and Lerch, B. A., 1996, “The effect of heat treatment on Young’s modulus, damping, and microhardness of SiC/Ti-15-3,” J. Mater. Sci., 31, pp. 1489–1493.10.1007/BF00357857 ↗
9. Lerch, B. A., and Saltsman, J. F., 1991, “Tensile Deformation Damage in SiC Reinforced Ti-15V-3Cr-3Al-3Sn,” NASA Technical Memorandum 103620, Lewis Research Center.
10. Allen, D. H., Eggleston, M. R., and Hurtado, L. D., 1994, “Recent Research on Damage Development in SiC/Ti Continuous Fiber Metal Matrix Composites,” Fracture of Composites, E. A. Armanios, ed., Key Engineering Materials series, Trans Tech Publications.
11. Mori, T., and Tanaka, K., 1973, “Average Stress in Matrix and Average Elastic Energy of Materials with Misfitting Inclusions,” Acta Metall., 21, pp. 571–574.10.1016/0001-6160(73)90064-3 ↗
12. Weng, G. J. , 1984, “Some Elastic Properties of Reinforced Solids with Special Reference to Isotropic ones Containing Spherical Inclusions,” Int. J. Ingrg. Sci., 22, pp. 845–856.10.1016/0020-7225(84)90033-8 ↗
13. Benveniste, Y. , 1987, “A New Approach to the Application of the Mori-Tanaka’s Theory in Composite Material,” Mech. Mater., 6, pp. 147–157.10.1016/0167-6636(87)90005-6 ↗
14. Gavazzi, A. C., and Lagoudas, D. C., 1990, “Incremental Elastoplastic Behavior of Metal Matrix Composites Based on Averaging Schemes,” Proceedings IUTAM Symposium on Inelastic Deformation of Composite Materials, G. J. Dvorak, ed., Springer-Verlag, pp. 465–485.10.1007/978-1-4613-9109-8_22 ↗
15. Hill, R. , 1965, “Theory of Mechanical Properties of Fibre-Strengthened Materials: III. Self-Consistent Model,” J. Mech. Phys. Solids, 13, pp. 189–198.10.1016/0022-5096(65)90008-6 ↗
16. Laws, N., and Dvorak, G. J., 1987, “The Effect of Fiber Breaks and Aligned Penny-Shaped Cracks on the Stiffness and Energy Release Rates in Uni-directional Composites,” Int. J. Solids Struct., 23, pp. 1269–1283.10.1016/0020-7683(87)90105-3 ↗
17. Dvorak, G. J., Laws, N., and Hejazi, M., 1985, “Analysis of Progressive Matrix Crack in Composites Laminates I. Thermoelastic Properties of a Ply with Cracks,” J. Compos. Mater., 19, pp. 216–234.10.1177/002199838501900302 ↗