journal article·2018-10-01

Effect of Tungsten Inert Gas Remelting on Microstructure, Interface, and Wear Resistance of Fe-Based Coating

Tianshun Dong, Xiaodong Zheng, Guolu Li, Haidou Wang, Ming Liu, Xiukai Zhou, Yalong Li

Publisher page

Abstract

Tungsten inert gas arc (TIG) process was employed to remelt Fe-based coating deposited by plasma spraying. Subsequently, the microstructure, interface, and the wear resistance of the coatings before and after remelting were studied. The results showed that the lamellar structure, pores, and inclusions of Fe-based coating were eliminated and the porosity significantly decreased from 4% to 0.4%. The as-sprayed coating contained microcrystalline region, nanocrystalline region, and transition region, while single crystal region and rod-shaped (Fe,Cr)23C6 were observed in the remelted coating. There was no element diffusion and dissolution phenomenon at the interface; thus, the bonding form between the as-sprayed coating and substrate mainly was mechanical bonding. On the contrary, the diffusion transfer belt (DTB) emerged at the interface of the remelted coating and substrate, the remelted coating was bonded with the substrate metallurgically. Additionally, the average microhardness and elastic modulus of the remelted coating increased by 33.4% and 53.2%, respectively, compared with the as-sprayed coating. During wear process, the as-sprayed coating exhibited obvious brittle fracture characteristics, while the remelted coating appeared typical plastic deformation characteristics and its weight loss reduced by 39.5%. Therefore, TIG remelting process significantly improved the microstructure, mechanical properties, and wear resistance of Fe-based coating.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Material Science and Engineering, Hebei University of Technology, Tianjin 300130, China e-mail:

National Key Laboratory for Remanufacturing, Academy of Armored Forces Engineering, Beijing 100072, China e-mail:

References (21)

Show source-provided references
1. Investigation of RCF Failure Prewarning of Fe-Based Coating by Online Monitoring10.1016/j.triboint.2013.12.016 ↗
2. Using In Situ Atomic Force Microscopy to Investigate the Kinetics of Corrosion of WC-Co-Cr Cermet Coatings Applied by High-Velocity Oxy-Fuel10.1115/1.2400258 ↗
3. Effect of TIG Surface Melting on Structure and Wear Properties of Air Plasma-Sprayed WC-Co Coatings10.1016/j.surfcoat.2014.11.050 ↗
4. Laser Remelting of Plasma-Sprayed Nanostructured Al2O3-20 wt.%ZrO2 Coatings Onto 316 L Stainless Steel10.1016/j.apsusc.2017.06.204 ↗
5. Surface Integrity Design of Plasma Sprayed Coating for Resisting Contact Fatigue10.1016/j.matchemphys.2016.05.025 ↗
6. Effects of Rod Carbide Size, Content, Loading and Sliding Distance on the Friction and Wear Behaviors of (Cr,Fe)7C3-Reinforced α-Fe Based Composite Coating Produced Via PTA Welding Process10.1016/j.surfcoat.2014.03.029 ↗
7. Multiaxial Fatigue Strength Assessment of Electroslag Remelted 50CrMo Steel Crankshafts10.1016/j.ijfatigue.2017.03.023 ↗
8. Failure Mode and Fatigue Mechanism of Laser-Remelted Plasma-Sprayed Ni Alloy Coatings in Rolling Contact10.1016/j.surfcoat.2010.08.122 ↗
9. Properties of NiCrBSi Coating, as Sprayed and Remelted by Different Technologies10.1016/j.surfcoat.2014.05.009 ↗
10. Corrosion Properties of In Situ Laser Remelted NiCrBSi Coatings Comparison With Hard Chromium Coatings10.1016/j.jmatprotec.2010.09.005 ↗
11. On the Effectiveness of Multi-Component Laser Modifying of Fe-Based Self-Fluxing Coating With Hard Particulates10.1016/j.surfcoat.2016.08.068 ↗
12. Microstructure and Corrosion Resistance of Induction Melted Fe-Based Alloy Coating10.1016/j.surfcoat.2014.04.045 ↗
13. Effect of Flame Remelting on Microstructure and Wear Behaviour of Plasma Sprayed NiCrBSi-30%Mo Coating10.1080/02670844.2016.1226053 ↗
14. Surface Alloying of Commercially Pure Titanium With Aluminium and Nitrogen Using GTAW Processing10.1016/j.surfcoat.2016.12.115 ↗
15. Remelting Treatment of the Non-Conductive Oxide Coatings by Means of the Modified GTAW Method10.1016/j.surfcoat.2011.12.009 ↗
16. Microstructure and Wear Properties of In Situ TiC/FeCrBSi Composite Coating Prepared by Gas Tungsten Arc Welding10.1016/j.wear.2005.01.007 ↗
17. Effect of Induction Remelting on the Microstructure and Properties of In Situ TiN-Reinforced NiCrBSi Composite Coatings10.1016/j.surfcoat.2018.02.024 ↗
18. The Effect of Laser Remelting on the Surface Chemistry of Ti6Al4V Components Fabricated by Selective Laser Melting10.1016/j.jmatprotec.2016.01.022 ↗
19. Wear Behavior of Bio-Inspired and Technologically Structured HVOF Sprayed NiCrBSiFe Coatings10.1016/j.surfcoat.2015.08.055 ↗
20. 2012
21. Effect of High-Temperature Furnace Treatment on the Microstructure and Corrosion Behavior of NiCrBSi Flame-Sprayed Coatings10.1016/j.corsci.2014.07.057 ↗