journal article·2016-07-01

Modeling and Experimental Assessment of Bending Characteristics of Laminated Bilayer Sheet Materials

Ganesh Govindasamy, Mukesh K. Jain

Publisher page

Abstract

Many mathematical models based on the advanced theory of bending to predict bending characteristics for monolithic sheet materials are available in the literature. In this work, a similar approach is utilized to develop bending models for a bilayer laminated sheet material. The principal stresses and strains through the thickness and change in relative thickness, at specified bend curvatures, are obtained as a function of increasing curvature during bending. Additionally, three-dimensional (3D) finite element (FE) based models for bilayer laminate bending are developed to overcome simplifications of the analytical models. In order to experimentally validate the two models, a new experimental bend test-jig is developed and experiments are performed on bilayer steel–aluminum laminate for different clad to matrix thickness ratios. These experiments have enabled continuous measurements of strain along the width at the bend line and through the laminate thickness at one of the specimen edges using an online strain mapping system based on digital image correlation (DIC) method. Analytical model results indicate how the through-thickness strain distribution and relative thickness of the specimen in bending are influenced by the location and thickness of the soft clad material. The FE model and experimental results exhibit similar trends in the relative thickness change for different geometric arrangements of steel–aluminum layers. The tangential and radial stresses decrease in magnitude with increasing aluminum clad thickness ratios. The 3D FE model of laminate bending provided strain predictions across the specimen width at the bend line on the tension and compression sides that increased with increasing clad thickness ratios. Also, relative thickness data from the 3D FE model showed uniaxial and plane strain stress states at the edge and midwidth sections of the test specimen. The results from analytical and FE models and from DIC and microscopic thickness measurements indicate that thickness at the bend line increases with increasing clad thickness for the case of clad layer on the compressive side of the laminate (i.e., C-C case) and vice versa for clad layer on the tensile side (C-T).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Advanced Surface Polishing Techniques · Laser and Thermal Forming Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Forming Technologies Incorporated, 3370, South Service Road, Burlington, ON L7N 3M6, Canada e-mail:

Department of Mechanical Engineering, McMaster University, JHE 326G, 1280 Main Street West, Hamilton, ON L8S 4L7, Canada e-mail:

References (23)

Show source-provided references
1. Mechanical Behaviour of Laminated Metal Composites10.1179/imr.1996.41.5.169 ↗
2. Direct Chill Casting of Aluminium–Manganese Against Aluminium–Silicon Layer Via Novelis Fusion Process10.1179/175355507X214069 ↗
3. Development of Aluminum-Clad Steel Sheet by Roll-Bonding10.2355/isijinternational1966.23.628 ↗
4. Macro- and Micro-Surface Engineering to Improve Hot Roll Bonding of Aluminum Plate and Sheet10.1016/j.msea.2007.06.022 ↗
5. Mechanical Properties and Press Formability of Copper/Mild Steel Sandwich Sheet Materials
6. Engineering Study of Sheet Bending
7. Plastisches Biegen von Blechen
8. The Mechanism of Forming in Bending
9. Plastic Bending of Work Hardening Materials10.1115/1.3185823 ↗
10. Plastic Bending of Anisotropic Sheet Metals10.1016/0020-7403(94)00069-V ↗
11. Mathematical Modeling of Plane Strain Bending of Sheet and Plate10.1016/0924-0136(93)90164-2 ↗
12. Semi-Analytical Process Modelling and Simulation of Air Bending10.1243/030932405X30966 ↗
13. Finite Deformation Elasto-Plastic Solution for the Pure Bending Problem of a Wide Plate of Elastic Linear-Hardening Material10.1016/0020-7683(94)90182-1 ↗
14. An Exact Solution for the Elastic Plastic Bending of Anisotropic Sheet Metal Under Conditions of Plane Strain10.1016/S0020-7403(01)00009-1 ↗
15. The Pure Plastic Bending of Laminated Sheet Metals10.1016/0020-7403(75)90061-2 ↗
16. Pure Plastic Bending of Sheet Laminates Under Plane Strain Condition10.1016/0020-7403(83)90082-6 ↗
17. Air Bending and Springback of Stainless Steel Clad Aluminum Sheet10.1016/j.jmatprotec.2009.09.010 ↗
18. The Forming Limit Curve for Bending Processes10.1016/0020-7403(79)90081-X ↗
19. 1950
20. GOM, 2001, Aramis—Deformation Measurement Using the Grating Method. User's Manual, V4.7-4.2, GOM mbH, Braunschweig, Germany.http://materials-science.phys.rug.nl/index.php/home/downloads/category/8-aramis-3d2d?download=25%3Aaramis-v47
21. Optimization of Digital Dmage Correlation for High-Resolution Strain Mapping of Ceramic Composites10.1007/s11340-012-9617-1 ↗
22. A High-Fidelity Strain-Mapping Framework Using Digital Image Correlation10.1016/j.msea.2013.11.020 ↗
23. Strain Localization and Damage Development During Bending of Al–Mg Alloy Sheets10.1016/j.msea.2012.04.093 ↗