Effects of Preheating on Microstructural and Mechanical Properties of Friction Stir Welded Thin Low Carbon Steel Joints
Source abstract
Abstract
Abstract Friction stir welding of a low carbon thin steel plate was performed with preheating the base material to increase the joining performance. The rotational speed of the tool was set from 1500 to 2000 rpm with a constant travel speed of 15 mm/min and preheating temperature of 50 to 150 °C. The tensile strength of 340 MPa was achieved for the preheated specimen compared with 310 MPa for the non-preheating specimen at the welding speed of 15 mm/min. Electron microscopic images of the preheated joint revealed a remarkable plasticized material flow and dynamic recrystallization, which resulted in the grain refinement that had increased the joining strength. The weld thinning issue was almost eliminated in the preheated welded specimen. However, by increasing the preheat temperature further, the tensile strength decreases due to the formation of defects from excessive heat. The preheated sample fractured at the base metal, revealing a ductile fracture mode.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Metal Forming Simulation Techniques · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
University of Malaya Department of Mechanical Engineering, Faculty of Engineering, , Kuala Lumpur 50603 , Malaysia
University of Malaya Department of Mechanical Engineering, Faculty of Engineering, , Kuala Lumpur 50603 , Malaysia ;
University of Malaya Centre of Advanced Manufacturing and Material Processing (AMMP Centre), , Kuala Lumpur 50603 , Malaysia
Funding
Universiti Malaya
References (39)
Show source-provided references
1. A Review on Friction Stir Welding of Steels10.1186/s10033-021-00655-3 ↗
2. Enhancements on Dissimilar Friction Stir Welding Between AZ31 and SPHC Mild Steel With Al-Mg as Powder Additives10.1115/1.4049745 ↗
3. Recent Research Progress in Friction Stir Welding of Aluminium and Copper Dissimilar Joint: A Review10.1016/j.jmrt.2021.09.037 ↗
4. Tool Performance Evaluation of Friction Stir Welded Shipbuilding Grade DH36 Steel Butt Joints10.1007/s00170-019-03618-0 ↗
5. Mechanical Properties of Friction Stir Welded St 37 and St 44 Steel Joints10.3139/120.111266 ↗
6. Effect of Surface States on Joining Mechanisms and Mechanical Properties of Aluminum Alloy (A5052) and Polyethylene Terephthalate (PET) by Dissimilar Friction Spot Welding10.3390/met6050101 ↗
7. A Review on Biomedical Implant Materials and the Effect of Friction Stir Based Techniques on Their Mechanical and Tribological Properties10.1016/j.jmrt.2022.01.050 ↗
8. Friction Stir Alloying of AZ61 and Mild Steel With Al- CNT Additive10.1080/13621718.2022.2080449 ↗
9. A Review on Nanomaterials Reinforcement in Friction Stir Welding10.1016/j.jmrt.2020.11.072 ↗
10. Effects of Al-Ni Powder Addition on Dissimilar Friction Stir Welding Between AA7075-T6 and 304 L10.1002/mawe.201900105 ↗
11. Experimental Studies on Controlling of Process Parameters in Dissimilar Friction Stir Welding of DH36 Shipbuilding Steel–AISI 1008 Steel10.1007/s40194-020-00886-3 ↗
12. Investigation of Forming Limit Curves and Mechanical Properties of 316 Stainless Steel/St37 Steel Tailor-Welded Blanks Produced by Tungsten Inert Gas and Friction Stir Welding Method10.1016/j.cirpj.2021.02.002 ↗
13. Dissimilar Friction Stir Welding of Duplex Stainless Steel to Low Alloy Structural Steel10.1179/1362171815Y.0000000063 ↗
14. Friction Stir Welding of Ductile Iron and Low Carbon Steel10.1179/136217110X12785889549507 ↗
15. Microstructure and Properties of CLAM/316L Steel Friction Stir Welded Joints10.1016/j.jmatprotec.2019.03.032 ↗
16. Effect of Tool Offset and Rotational Speed in Dissimilar Friction Stir Welding of AISI 304 Stainless Steel and Mild Steel10.1007/s11665-019-04362-y ↗
17. Experimental Comparison of the Effects of Superimposed Axial and Bending Ultrasonic Vibrations on Friction Stir Welding Process10.1177/0954405417729414 ↗
18. Auxiliary Energy Assisted Friction Stir Welding—Status Review10.1179/1362171815Y.0000000048 ↗
19. Evaluation of an Induction-Assisted Friction Stir Welding Technique for Super Duplex Stainless Steels10.1002/sia.5442 ↗
20. Development of Microstructure and Mechanical Properties in Laser-FSW Hybrid Welded Inconel 60010.2320/matertrans.M2009058 ↗
21. Microstructure and Mechanical Properties of S45C Steel Prepared by Laser-Assisted Friction Stir Welding10.1016/j.matdes.2012.12.078 ↗
22. Joining of Dissimilar AZ31B Magnesium Alloy and SS400 Mild Steel by Hybrid Gas Tungsten Arc Friction Stir Welding10.1007/s12540-013-6016-9 ↗
23. Numerical Optimisation of Laser Assisted Friction Stir Welding of Structural Steel10.1080/13621718.2019.1570682 ↗
24. Weld Microstructure and Mechanical Properties in Ultrasonic Enhanced Friction Stir Welding of Al Alloy to Mg Alloy10.1016/j.jmatprotec.2017.11.031 ↗
25. Modeling the Effects of Ultrasonic Vibration on Friction Stir Welding10.1016/j.jmatprotec.2015.03.002 ↗
26. Challenges, Process Requisites/Inputs, Mechanics and Weld Performance of Dissimilar Micro-Friction Stir Welding (Dissimilar ΜFSW): A Comprehensive Review10.1016/j.jmapro.2021.05.045 ↗
27. Microstructures and Mechanical Properties of Micro Friction Stir Welding (ΜFSW) of 6061-T4 Aluminum Alloy10.1016/j.jmrt.2017.10.010 ↗
28. Recent Progress in Friction Stir Welding Tools Used for Steels10.1007/s42243-018-0066-7 ↗
29. Effect of Plasma Preheating on Weld Quality and Tool Life During Friction Stir Welding of DH36 Steel10.1177/0954405421990139 ↗
30. Predictions of the Optimized Friction Stir Welding Process Parameters for Joining AA7075-T6 Aluminum Alloy Using Preheating System10.1007/s00170-014-5963-8 ↗
31. Spot Friction Stir Welding of Low Carbon Steel Plates Preheated by High Frequency Induction10.1016/j.matdes.2013.08.071 ↗
32. Microstructure and Mechanical Properties of Mild Steel Joints Prepared by a Flat Friction Stir Spot Welding Technique10.1016/j.matdes.2012.01.027 ↗
33. The Effect of SiC Particles on the Microstructure and Mechanical Properties of Friction Stir Welded Pure Copper Joints10.1016/j.msea.2011.03.077 ↗
34. Gas Tungsten Arc Welding Assisted Hybrid Friction Stir Welding of Dissimilar Materials Al6061-T6 Aluminum Alloy and STS304 Stainless Steel10.1016/j.matdes.2011.12.018 ↗
35. The Effect of Preheating on Mechanical Properties of Friction Stir Welded Dissimilar Joints of Pure Copper and AA7075 Aluminum Alloy Sheets10.1007/s00170-015-7877-5 ↗
36. Microstructure and Mechanical Properties of Keyhole Repair Welds in AA 7075-T651 Using Refill Friction Stir Spot Welding10.1016/j.matdes.2017.07.013 ↗
37. Effects of Travel Speed on Mechanical Properties of AA7075-T6 Ultra-Thin Sheet Joints Fabricated by High Rotational Speed Micro Pinless Friction Stir Welding10.1016/j.jmatprotec.2018.10.006 ↗
38. Recent Progress on Control Strategies for Inherent Issues in Friction Stir Welding10.1016/j.pmatsci.2020.100706 ↗
39. Micro Friction Stir Welding of Ultra-Thin Al-6061 Sheets10.1016/j.jmatprotec.2017.07.031 ↗