journal article·2022-10-01

Experimental Study on Laser-Induced Surface Damage of a Single-Crystal Nickel-Based Superalloy Under Continuous Wave Fiber Laser Scanning Process

Srinivasa Rao Nandam, A. Venugopal Rao, Amol A. Gokhale, Suhas S. Joshi

Publisher page

Abstract

Abstract Single-crystal (SC) nickel-based superalloy castings offer high-temperature mechanical properties that result in superior gas turbine engine performance and durability. These castings undergo various precision machining operations to remove a significant amount of material while manufacturing. Here, nickel-based superalloys are one of the most difficult materials to be cut. Therefore, novel concepts are being employed to improve their machinability including lowering their surface strength. This paper presents the introduction of laser-induced surface damage (LISD) on a second-generation SC nickel-based superalloy using a continuous wave (CW) fiber laser. Laser scanning experiments were performed on SC specimens in the as-cast condition with a laser power of 1000 W, a beam diameter of 1.2 mm, and scanning speeds from 5.5 mm/s to 16.5 mm/s. The cross-sections of the laser-irradiated surfaces were investigated by measuring the irradiated geometries (IRG), microstructural changes, microsegregations, solidification cracking, and heat affected zone (HAZ). The IRG shows the conduction mode of penetration with a high width-to-depth ratio under a bigger beam diameter and top-hat type beam profile. The IRG boundaries have irregular profiles due to the dissolution of interdendrite regions and eutectic phases. The IRG showed fine dendrites and solidification cracks with reduced microsegregation levels. The solidification cracking is mainly attributed to thermal stresses and the microcracking in HAZ is attributed to the dissolution of low melting Mo and Ti eutectics. The evolved HAZ ranges from 15% to 20% of the IRG depth. The LISD volume is evaluated as IRG plus HAZ for removal by machining process.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Indian Institute of Technology Bombay, Powai, Mumbai 400076, India;

Defence Metallurgical Research Laboratory, DRDO, Kanchanbagh, Hyderabad 500058, India

Department of Mechanical Engineering, Indian Institute of Technology Bombay, Powai, Mumbai 400076, India

Department of Mechanical Engineering, Indian Institute of Technology Indore, Simrol, Indore 453552, India

References (33)

Show source-provided references
1. Nickel-Based Superalloys for Advanced Turbine Engines: Chemistry, Microstructure, and Properties10.2514/1.18239 ↗
2. Reed · 2006 · 110.1017/CBO9780511541285 ↗
3. Machinability of Nickel-Based High Temperature Alloys10.1080/10940340008945703 ↗
4. Tool Wear Mechanisms in the Machining of Nickel Based Super-Alloys10.1007/s11465-014-0301-2 ↗
5. Laser-Assisted Machining of Inconel 718 With an Economic Analysis10.1016/j.ijmachtools.2005.11.005 ↗
6. Turbine Blades of the Single Crystal Nickel Based CMSX-6 Superalloy
7. High-Power Disk and Fiber Lasers: A Performance Comparison10.1117/12.913286 ↗
8. Modern Fiber Laser Beam Welding of the Newly Designed Precipitation Strengthened Nickel-Based Superalloys10.1016/j.optlastec.2013.09.030 ↗
9. Stray Grain Formation in Welds of Single-Crystal Ni-Base Superalloy CMSX-410.1007/s11661-009-0078-9 ↗
10. Origin of Stray-Grain Formation and Epitaxy Loss at Substrate During Laser Surface Remelting of Single-Crystal Nickel-Base Superalloys10.1016/j.matdes.2016.04.051 ↗
11. Microstructures and Microhardness Properties of CMSX-4 Additively Fabricated Through Scanning Laser Epitaxy (SLE)10.1007/s11665-017-3008-9 ↗
12. Carter · 2012 · 577
13. Laser Cladding for Crack Repair of CMSX-4 Single-Crystalline Turbine Parts10.1007/s40516-016-0033-8 ↗
14. Causes Analysis on Cracks in Nickel-Based Single Crystal Superalloy Fabricated by Laser Powder Deposition Additive Manufacturing10.1016/j.matdes.2018.10.042 ↗
15. Fiber Laser Surface Remelting of a Nickel-Based Superalloy by an Integrated Rectangular Laser Spot10.1016/j.optlaseng.2018.07.010 ↗
16. The Initiation and Propagation Mechanism of the Overlapping Zone Cracking During Laser Solid Forming of IN-738 LC Superalloy10.1016/j.jallcom.2018.03.366 ↗
17. On the Solidification Behaviour and Cracking Origin of a Nickel-Based Superalloy During Selective Laser Melting10.1016/j.matchar.2018.12.032 ↗
18. Investigation of Cracking Causes During Multi-Pass Laser Cladding of Heat Resistant Single Crystal Nickel Alloy10.1016/j.procir.2020.09.059 ↗
19. Harris · 2004 · 45
20. Dendritic Segregation and Arm Spacing in Directional Solidified CMSX-4 Superalloy10.1080/13640461.2016.1166726 ↗
21. Microstructure and Solidification Sequence of the Inter Dendritic Region in a Third Generation Single-Crystal Nickel-Base Superalloy10.1007/s11661-009-9855-8 ↗
22. Effect of Processing Parameters on Crystal Growth and Microstructure Formation in Laser Powder Deposition of Single-Crystal Superalloy10.1016/j.jmatprotec.2014.08.025 ↗
23. Effect of Very High Temperature Short Exposures on the Dissolution of the γ’ Phase in Single Crystal MC2 Superalloy10.1007/s10853-007-1645-3 ↗
24. Phase Transformation in CMSX-4 Nickel-Based Superalloy10.1088/1757-899X/35/1/012005 ↗
25. Studies of the Thermophysical Properties of Commercial CMSX-4 Alloy10.1021/je900132m ↗
26. Single-Crystal Laser Deposition of Superalloys: Processing—Microstructure Maps10.1016/S1359-6454(00)00367-0 ↗
27. Microsegregation Behavior of Alloying Elements in Single-Crystal Nickel-Based Superalloys With Emphasis on Dendritic Structure10.1016/j.matchar.2017.02.030 ↗
28. Weld Metal Cracking in Laser Beam Welded Single Crystal Nickel-Based Superalloys10.1179/174328407X185938 ↗
29. Development of Microstructures in Laser Surface Remelting of DD2 Single Crystal10.1016/S1359-6454(01)00340-8 ↗
30. Microstructural and Compositional Design of Ni-Based Single Crystalline Superalloys: A Review10.1016/j.jallcom.2018.01.224 ↗
31. Measurement of Laser Absorptivity for Operating Parameters Characteristic of Laser Drilling Regime10.1088/0022-3727/41/15/155502 ↗
32. Welding With High Power Fiber Lasers—A Preliminary Study10.1016/j.matdes.2006.01.009 ↗
33. The Theory of Moving Sources of Heat and Its Application to Metal Treatments