journal article·2026-01-01

Impact of Cold Metal Transfer and Pulse Multicontrol Heat Inputs on SS316L Wire Arc Additively Manufactured Built-Up Properties and Performance

Saboor Fayaz Lone, Dinesh W. Rathod, Sheikh Nazir Ahmad

Publisher page

Abstract

Abstract Wire arc additive manufacturing (WAAM), leveraging traditional gas metal arc welding (GMAW) technology, offers a promising approach for fabricating large-scale metallic components with high deposition rates. Among GMAW-based processes, cold metal transfer (CMT) and pulsed metal inert gas (MIG) techniques differ significantly in their metal transfer mechanisms and thermal inputs, which directly influence the resulting material properties. This study systematically compares the microstructural, mechanical, tribological, and corrosion characteristics of 316L stainless steel walls produced using CMT and pulsed MIG WAAM processes under similar heat input conditions (CMT: 323.48 J/mm, pulsed MIG: 329.14 J/mm). The CMT process produced finer grains (11.16 µm) compared to pulsed MIG (14.14 µm), contributing to slightly higher microhardness (171.90 HV versus 171.14 HV) and improved mechanical properties. Charpy impact toughness, yield strength, and ultimate tensile strength were all higher for the CMT process by 16.4%, 3.4%, and 1.3%, respectively, while pulsed MIG showed slightly higher elongation (56% versus 52.25%). Fractographic analysis revealed finer, more uniform dimples in the CMT samples, indicating ductile fracture behavior. In terms of tribological performance, the CMT process exhibited a lower coefficient of friction (0.216 versus 0.249) and a significantly reduced wear-rate (3.4 × 10−3 mm3/m versus 5.5 × 10−3 mm3/m). Corrosion resistance was also marginally better in the CMT samples, with a corrosion rate of 0.05235 mm/year compared to 0.05524 mm/year for pulsed MIG. Overall, the CMT process consistently outperformed pulsed MIG across multiple performance metrics, making it a more favorable choice for high-integrity additive manufacturing of stainless steel components.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

NIT Srinagar Department of Mechanical Engineering, , , ,

NIT Kurukshetra Department of Mechanical Engineering, , , ,

References (35)

Show source-provided references
1. CMT-Based Wire Arc Additive Manufacturing Using 316 L Stainless Steel: Effect of Heat Accumulation on the Multi-Layer Deposits10.3390/met10020278 ↗
2. Wire-Feed Additive Manufacturing of Metal Components: Technologies, Developments and Future Interests10.1007/s00170-015-7077-3 ↗
3. Monitoring Approach to Evaluate the Performances of a New Deposition Nozzle Solution for DED Systems10.3390/technologies5020029 ↗
4. Potentials and Strategies of Solid-State Additive Friction-Stir Manufacturing Technology: A Critical Review10.1016/j.jmapro.2018.09.030 ↗
5. Wire and Arc Additive Manufacturing: Opportunities and Challenges to Control the Quality and Accuracy of Manufactured Parts10.1016/j.matdes.2021.109471 ↗
6. Microstructure and Mechanical Properties of AISI 316L Produced by Directed Energy Deposition-Based Additive Manufacturing: A Review10.3390/app10093310 ↗
7. Thermo-Mechanical Analysis of Wire and Arc Additive Layer Manufacturing Process on Large Multi-Layer Parts10.1016/j.commatsci.2011.06.023 ↗
8. Rapid Prototyping Using 3-D Welding
9. Metal Transfer Modes in Plasma Wire + Arc Additive Manufacture10.1016/j.jmatprotec.2018.08.043 ↗
10. Vision-Sensing and Bead Width Control of a Single-Bead Multi-Layer Part: Material and Energy Savings in GMAW-Based Rapid Manufacturing10.1016/j.jclepro.2012.10.009 ↗
11. Cold Metal Transfer (CMT) Based Wire and Arc Additive Manufacture (WAAM) System10.1134/S102745101901004X ↗
12. Shaped Metal Deposition Technique in Additive Manufacturing: A Review10.1177/0954405416640181 ↗
13. Investigation on the Process Window With Liner Energy Density for Single-Layer Parts Fabricated by Wire and Arc Additive Manufacturing10.1016/j.jmapro.2020.05.054 ↗
14. Microstructure and Deformation Behavior of Ti-6Al-4 V Alloy by High-Power Laser Solid Forming10.1016/j.actamat.2017.04.026 ↗
15. Grain Morphology Evolution and Texture Characterization of Wire and Arc Additive Manufactured Ti-6Al-4 V10.1016/j.jallcom.2018.07.235 ↗
16. Regional Control and Optimization of Heat Input During CMT by Wire Arc Additive Manufacturing: Modeling and Microstructure Effects10.3390/ma14051061 ↗
17. Effect of Welding Heat Input on Grain Size and Microstructure of 316L Stainless Steel Welded Joint10.4028/www.scientific.net/AMM.331.578 ↗
18. Low-Energy High-Current Electron Beam Heating of Target With Second-Phase Microinclusions10.1134/S1063785011080256 ↗
19. Effect of Heat-Treatment on the Microstructure, Mechanical Properties and Corrosion Behaviour of SS 316 Structures Built by Laser Directed Energy Deposition Based Additive Manufacturing10.1007/s12540-020-00838-y ↗
20. Experimental Investigations on Mechanical Properties of Multi-Layered Structure Fabricated by GMAW-Based WAAM of SS316L10.1016/j.jmrt.2022.08.074 ↗
21. A Comparative Study on the Microstructure, Mechanical Properties, Wear and Corrosion Behaviors of SS 316 Austenitic Stainless Steels Manufactured by Casting and WAAM Technologies10.1016/j.cirpj.2023.10.005 ↗
22. Experimental Investigations on the Microstructural Evolution and Their Influence on Mechanical, Tribological and Corrosion Performance of Wire-Arc Additive Manufactured SS316L Structure10.1016/j.mtcomm.2023.107673 ↗
23. Experimental Investigations on the Multi-Layered SS316L Wall Fabricated by CMT-Based WAAM: Mechanical and Microstructural Studies10.1016/j.jalmes.2023.100013 ↗
24. Mechanical Properties and Microstructure of SS 316 L Created by WAAM Based on GMAW10.1016/j.mtcomm.2023.107807 ↗
25. Characterization of an Austenitic Stainless Steel Preform Deposited by Wire Arc Additive Manufacturing10.1007/s00170-022-10382-1 ↗
26. The Fracture of Metals10.1016/0079-6425(63)90036-7 ↗
27. The Hardness of Additively Manufactured Alloys10.3390/ma11112070 ↗
28. Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material10.1016/j.jobe.2023.106988 ↗
29. A Review on Wire Arc Additive Manufacturing Based on Cold Metal Transfer10.1080/10426914.2024.2323441 ↗
30. Coeffi · 2011
31. Tribological Characteristics of ABS Structures With Different Infill Densities Tested by Pin-on-Disc10.1177/13506501231153521 ↗
32. Effect of Medium Entropy Alloy Powder-Core Wire on Friction Wear and Corrosion Resistance of Arc Cladding Additive Layer10.1088/2053-1591/aba84f ↗
33. Microstructure and Sliding Wear Behavior of Pure Titanium Surface Modified by Double-Glow Plasma Surface Alloying With Nb10.1016/j.matdes.2013.05.061 ↗
34. Wear of A380M Aluminum Alloy Under Reciprocating Load10.1007/s11665-010-9595-3 ↗
35. Wire Arc Deposition Additive Manufacturing and Experimental Study of 316 L Stainless Steel by CMT+p Process10.3390/met10111419 ↗