journal article·2008-07-01

Properties of Friction-Stir Welded Aluminum Alloys 6111 and 5083

W. Gan, K. Okamoto, S. Hirano, K. Chung, C. Kim, R. H. Wagoner

Publisher page

Abstract

Abstract Friction-stir welding (FSW) promises joints with low porosity, fine microstructures, minimum phase transformation, and low oxidation compared with conventional welding techniques. It is capable of joining combinations of alloys not amenable to conventional welding. Certain combinations of FSW parameters were used to create FSWs of aluminum alloys 5083-H18 and 6111-T4, and the physical weld defects were measured. The mechanical behavior of FSW welds made under the most favorable choice of parameters was determined using tensile tests and hardness measurements and was correlated to the microstructures of the weld and base material. Stir zones (SZs) in the 5083 specimens were much softer than the strain-hardened base materials. SZs in the 6111 material are approximately as hard as the base material. Natural aging of 6111 FSW specimens occurred in some parts of the heat-affected zone and produced hardening for up to 12weeks after welding. Annealing of 5083 FSW specimens produced abnormal grain growth (AGG) for welds produced under certain welding conditions and in certain parts of the weld zone. AGG is more severe for low-heat conditions, i.e., higher tool travel speed but lower rotational speed. The conditions for most favorable FSW are presented, as well as the expected microstructures and mechanical properties, along with the weld conditions that promote AGG.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Simulia Minneapolis/St. Paul Office, , 539 Bielenberg Drive Suite 110, Woodbury, MN 55125

Hitachi America, Ltd. R&D Division, , 34500 Grand River Avenue, Farmington Hills, MI 48335

Hitachi Research Laboratory , Hitachi Ltd. 7-1-1 Omika, Hitachi, Ibaraki 319-1292, Japan

Seoul National University School of Materials Science and Engineering, , 56-1 Shinlim-dong, Kwanak-gu, Seoul 151-742, Korea

Materials and Processes Laboratories , General Motors R&D Center, 30500 Mound Road, MC 480106224, Warren, MI 48090

The Ohio State University Department of Materials Science and Engineering, , 2041 College Road, Columbus, OH 43210

References (46)

Show source-provided references
1. The Use of Tailor-Welded Blanks in Automotive Applications
2. Forming of Tailor-Welded Blanks
3. Forming of Tailor-Welded Aluminum Blanks
4. A TEM Study of Precipitation and Related Microstructures in Friction-Stir-Welded 6061 Aluminum10.1023/A:1004385928163 ↗
5. Friction-Stir Welding Effects on Microstructure and Fatigue of Aluminum Alloy 7050-T745110.1007/s11661-000-0136-9 ↗
6. Friction Stir Welding vs. Fusion Welding
7. Microstructural Evolution of 6063 Aluminum During Friction-Stir Welding10.1007/s11661-999-0251-1 ↗
8. Friction Stir Welding and Processing
9. Microstructural Factors Governing Hardness in Friction-Stir Welds of Solid-Solution-Hardened Al Alloys10.1007/s11661-001-0178-7 ↗
10. Friction Stir Welding After a Decade of Development—Its Not Just Welding Anymore
11. A New Route to Bulk Nanocrystalline Materials10.1557/JMR.2003.0243 ↗
12. Grain Shape of Friction Stirred Al 7075 via Microscopic Approach
13. Mahoney · 183
14. Characterization of a Friction-Stir-Welded Aluminum Alloy 601310.1007/s11663-002-0059-5 ↗
15. Microstructural Aspects of the Friction-Stir Welding of 6061-T6 Aluminum10.1016/S1359-6462(97)00093-6 ↗
16. Characterization of Superplastic Deformation Behavior of a Fine Grain 5083 Al Alloy Sheet10.1007/BF02651938 ↗
17. Deformation Mechanisms During Low and High Temperature Superplasticity in 5083 Al–Mg Alloy10.1007/s11661-002-0062-0 ↗
18. The Aluminum Association, 2001, “Aluminum: The Corrosion Resistant Automotive Material,” Publication AT7, p. 14.
19. The Precipitation Sequence of Al–Mg–Si Alloys10.1016/S1359-6454(98)00059-7 ↗
20. Evaluation of Microstructure and Superplasticity in Friction Stir Processed 5083 Al Alloy10.1557/JMR.2004.0429 ↗
21. Aluminum and Aluminum Alloys10.31399/asm.tb.aub.t61170351 ↗
22. Matrix High-Speed Steels
23. Shaw · 443
24. ASTM, “E8 Standard Test Methods of Tension Testing of Metallic Materials,” Annual Book of ASTM Standards, American Society for Testing and Materials, Vol. 3.01.
25. Parameters Controlling Microstructure and Hardness During Friction-Stir Welding of Precipitation-Hardenable Aluminum Alloy 606310.1007/s11661-002-0124-3 ↗
26. Hall-Petch Relationship in Friction Stir Welds of Equal Channel Angular-Pressed Aluminium Alloys
27. Friction Stir Welding (FSW) Process10.1533/wint.2003.3174 ↗
28. Kim, D., Lee, W., Kim, J., Chung, K.-H., Kim, C., Okamoto, K., Wagoner, R. H., and Chung, K., 2008, “Material Characterization of Friction Stir Welded TWB Automotive Sheets,” unpublished.
29. Brandes · 21
30. Joining of 5083 and 6061 Aluminum Alloys by Friction Stir Welding10.1023/A:1022688908885 ↗
31. Formability and Strength of Friction-Stir-Welded Aluminum Sheets10.1007/s11661-004-0183-8 ↗
32. Comparison of Explicit and Implicit Finite Element Methods in the Quasistatic Simulation of Uniaxial Tension
33. Yao, Z. C., Zhang, L., Kariat, S., and Zhou, Y. J., 2007, “Tailor-Welded Aluminum Blanks for Liftgate Inner,” SAE Paper No. 2007-01-0421.10.4271/2007-01-0421 ↗
34. Metals Handbook
35. Krajewskim, P. E., and Ryntz, E. F., 1999, “Method for Improving the Hemmability of Age-Hardenable Aluminum Sheet,” U.S. Patent No. 5,948,185.
36. Heat Treatment Effects on Bending in AA6111
37. Krajewski, P. E. , 2006, “The Effect of Retrogression Heat Treatments on Aluminum Flanging and Trimming,” SAE Technical Paper No. 2006-01-0984.10.4271/2006-01-0984 ↗
38. Improvement of Mechanical Properties for Al Alloys Using Equal-Channel Angular Pressing10.1016/S0924-0136(01)00783-X ↗
39. Stability of Nugget Zone Grain Structures in High Strength Al-Alloy Friction Stir Welds During Solution Treatment10.1016/S1359-6454(02)00598-0 ↗
40. A Unified Theory of Recovery, Recrystallization and Grain Growth, Based on the Stability and Growth of Cellular Microstructures. 1. The Basic Model10.1016/S1359-6454(97)00070-0 ↗
41. Friction Stir Welding of a Commercial 7075-T6 Aluminum Alloy: Grain Refinement, Thermal Stability and Tensile Properties10.2320/matertrans.45.2503 ↗
42. SEM-EBSD Characterization of the Deformation Microstructure in Friction Stir Welded 2024 T351 Aluminum Alloy
43. Microtexture in the Friction-Stir Weld of an Aluminum Alloy10.1007/s11661-001-0351-z ↗
44. Analytical Modeling of Grain Growth in Metals and Alloys in the Presence of Growing and Dissolving Precipitates. 2. Abnormal Grain Growth10.1016/0956-7151(94)00489-5 ↗
45. Friction Stir Welding Parameters: A Tool for Controlling Abnormal Grain Growth During Subsequent Heat Treatment
46. The Effect of Grain Size on Fatigue Growth in an Aluminum Magnesium Alloy10.1111/j.1460-2695.1995.tb00861.x ↗