journal article·1995-04-01

A Constitutive Model for Commercially Pure Titanium

J. Y. Sheikh-Ahmad, J. A. Bailey

Publisher page

Abstract

Flow stress data for CP titanium were obtained using the torsion test in the temperature range from ambient to 750°C and at shear strain-rates in the range from 0.192 to 122.0 s−1. The temperature rise because of deformation heating was calculated numerically. It was found that the temperature rise is insignificant for strain rates below 0.192 s−1 where the deformation conditions are essentially isothermal while for strain rates above 27.0 s−1 deformation conditions are adiabatic. Large temperature gradients exist in the longitudinal direction of the specimen with the maximum temperature occurring at the middle of the gage length. The temperature gradients in the radial direction are much smaller and can be neglected for most practical applications. Isothermal shear stress-shear strain curves for CP titanium were obtained from the experimental torsion test data by accounting for the temperature rise produced by deformation. It was found that the data exhibits a good fit to a Johnson-Cook relationship with exponential thermal softening. The work emphasizes the importance of the need to consider the role of deformation heating when interpreting data on the effect of strain rate and temperature on the mechanical properties of materials.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metallurgy and Material Forming · High-Velocity Impact and Material Behavior · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical and Aerospace Engineering, North Carolina State University, P.O. Box 7910, Raleigh, NC 27696-7910

References (17)

Show source-provided references
1. Bailey J. A. , HaasS. L., and ShahM. K., 1972, “Effect of Strain-Rate and Temperature on the Resistance to Torsional Deformation of Several Aluminum Alloys,” Int. J. Mech. Sci., Vol. 14, p. 735735.10.1016/0020-7403(72)90012-4 ↗
2. Farren W. S. , and TaylorG. I., 1925, “The Heat Developed During Plastic Extension of Metals,” Proc. Royal Soc., London, Series A107, p. 422422.10.1098/rspa.1925.0034 ↗
3. Harding, J., 1989, “The Development of Constitutive Relationships for Material Behavior at High Rates of Strain,” Int. Conf. Mech. Prop. Materials at High Rates of Strain, Oxford, p. 189.
4. Johnson G. R. , 1981, “Dynamic Analysis of a Torsion Test Specimen Including Heat Conduction and Plastic Flow,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 103, p. 201201.10.1115/1.3225001 ↗
5. Johnson, G. R., and Cook, W. H., 1983a, “A Constitutive Model and Data for Metals Subjected to Large Strains, High Strain Rates and High Temperatures,” Proc. 7th Int. Symp. on Ballistics, The Hague, The Netherlands, p. 541.
6. Johnson G. R. , HoegfeldtJ. M., LindholmU. S., and NagyA., 1983b, “Response of Various Metals to Large Torsional Strains over Large Range of Strain Rates—Part 1: Ductile Metals,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 105, p. 4242.10.1115/1.3225618 ↗
7. Johnson G. R. , HoegfeldtJ. M., LindholmU. S., and NagyA., 1983c, “Response of Various Metals to Large Torsional Strains over Large Range of Strain Rates—Part 2: Less Ductile Metals,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 105, p. 4848.10.1115/1.3225618 ↗
8. Kobayashi H. , and DoddB., 1989, “A Numerical Analysis for the Formation of Adiabatic Shear Bands Including Void Nucleation and Growth,” Int. J. Impact Engng., Vol. 8, No. 1, p. 11.10.1016/0734-743X(89)90027-4 ↗
9. Kobayashi H. , and DoddB., 1987, “Estimation of Errors in Torsion Testing,” Res Mechanica, Vol. 20, p. 163163.
10. McQueen, H. J., and Bourel, D. L., 1987, “Hot Workability of Metals and Alloys,” J. Metals, Sept., p. 28.10.1007/BF03257647 ↗
11. McQuillan, A. D., and McQuillan, M. K., 1955, Titanium, Butterworths, London.
12. Miller, A. K., ed., 1987, Unified Constitutive Equations for Creep and Plasticity, Elsevier, London.10.1007/978-94-009-3439-9 ↗
13. Rao K. P. , DoraiveluS. M., and CopinathanV., 1982, “Flow Curves and Deformation on Materials at Different Temperatures and Strain Rates,” J. Mech. Working Tech., Vol. 6, p. 6363.10.1016/0378-3804(82)90020-1 ↗
14. Semiatin S. L. , LahotiG. D., and JonasJ. J., 1985, “Application of The Torsion Test to Determine Workability,” Metals Handbook, ASM, Vol. 8, p. 154154.
15. Taylor G. I. , and QuinneyH., 1934, “The Latent Energy Remaining in a Metal After Cold Working,” Proc. Royal Soc., London, Series A143, p. 307307.10.1098/rspa.1934.0004 ↗
16. Vinh, T., Afzali, M., and Roche, A., 1979, “Fast Fracture of Some Usual Metals at Combined High Strain and High Strain Rate,” Mechanical Behavior of Materials, K. J. Miller and R. F. Smith, eds., p. 633.10.1016/B978-1-4832-8414-9.50087-0 ↗
17. White C. S. , 1992, “An Analysis of the Thin-Walled Torsion Specimen,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 114, p. 384384.10.1115/1.2904189 ↗