Effect of Material Anisotropy and Curing Stresses on Interface Delamination Propagation Characteristics in Multiply Laminated FRP Composites
Source abstract
Abstract
The present study encompasses the thermoelastic effect of material anisotropy and curing stresses on interlaminar embedded elliptical delamination fracture characteristics in multiply laminated fiber-reinforced polymeric (FRP) composites. Two sets of full three-dimensional finite element analyses have been performed to calculate the displacements and interlaminar stresses along the delaminated interface responsible for the delamination onset and propagation. Modified crack closure integral methods based on the concepts of linear elastic fracture mechanics have been followed to evaluate the individual modes of strain energy release rates along the delamination front. It is shown that the individual modes of energy release rates vary along the delamination front depending on the ply sequence, orientation, and thermoelastic material anisotropy of the constituting laminae. This causes the anisotropic and non-self similar delamination propagation along the interface. The asymmetric and nonuniform variations in the nature of energy release rate plots obtained in a thermomechanical loading environment are significant when curing stress effects are included in the numerical analysis and hence should be taken into account in the designs of laminated FRP composite structures.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Mechanical Behavior of Composites · Structural Behavior of Reinforced Concrete · Structural Response to Dynamic Loads
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mechanical Engineering Department, Indian Institute of Technology, Kharagpur-721302, West Bengal, India
References (31)
Show source-provided references
1. Curing Stresses in Composite Laminates10.1177/002199837500900110 ↗
2. Shear Deformation in Heterogeneous Anisotropic Plates
3. Material Characterization on the Fracture of Filament—Reinforced Composites10.1177/002199837500900207 ↗
4. Lekhnitski10.1063/1.3051394 ↗
5. Damage Development in Carbon/Epoxy Laminates Under Quasi-Static and Dynamic Loading10.1016/S0266-3538(99)00089-5 ↗
6. Modeling of Compressive Failure in Fiber Reinforced Composites10.1016/S0020-7683(99)00010-4 ↗
7. Role of Interphase on Elastic Behavior of Composite Materials: Theoretical and Experimental Analysis
8. Fatigue Failure Model for Fiber-Reinforced Materials Under General Loading Conditions10.1177/002199839402801503 ↗
9. An Accumulative Damage Model for Tensile and Shear Failures of Laminated Composite Plates10.1177/002199839502900705 ↗
10. Fracture Behavior of FRP Composite Laminates With an Embedded Elliptical Delamination at the Interface10.1106/7B1E-1A7K-RTBP-VXVR ↗
11. Energy Release Rate Determination for Edge Delamination Under Combined In-Plane, Bending and Hygrothermal Loading. Part II—Two Symmetrically Located Delaminations10.1177/002199839402801405 ↗
12. Analysis of Delamination Growth in Laminated Composites With Consideration for Residual Thermal Stress Effects10.1177/0021998302036011592 ↗
13. Thermal Stresses in a Non-homogeneous Orthotropic Elastic Multilayered Cylinder
14. Integrated Thermal and Mechanical Analysis of Composite Plates and Shells10.1016/S0266-3538(00)00117-2 ↗
15. Three-Dimensional Thermoelastic Analysis of Cracked Plain Weave Glass/Epoxy Composites at Cryogenic Temperatures10.1016/j.compscitech.2004.04.003 ↗
16. Quadratic Stress Criterion for Initiation of Delamination10.1177/002199838802201205 ↗
17. Failure of Quasi-Isotropic Composite Laminates With Free-Edges
18. Mixed-Mode Strain-Energy—Release Rate Effects on Edge Delamination of Composites
19. On the Calculation of Energy Release Rates for Cracked Laminates10.1007/BF00017790 ↗
20. Fracture Mechanics and Mechanisms of Impact-Induced Delamination in Laminated Composites10.1177/002199839502900202 ↗
21. Finite Element Estimates of Strain Energy Release Rate Components at the Tip of an Interface Crack Under Mode I Loading
22. Strain Energy Release Rate Formulae for Skin-Stiffener Debond Modeled With Plate Elements10.1016/0013-7944(95)00088-7 ↗
23. Point-Wise Energy Release Rate in Delaminated Plates10.2514/3.12441 ↗
24. Delaminations in Composite Plates Under Transverse Static or Impact Loads—A Model10.1016/0263-8223(93)90221-B ↗
25. Analysis of Stresses and Strain Near the End of a Crack Traversing a Plate10.1115/1.4011547 ↗
26. Fracture Mechanics of Delamination Problems in Composite Materials10.1177/002199837701100409 ↗
27. A Finite Element Model for Delamination in Composite Plates10.1080/10759419508945829 ↗
28. Effect of Shear Deformation and Continuity on Delamination Modeling With Plate Elements10.2514/6.1998-2023 ↗
29. Efficient Modeling of Postbuckling Delamination Growth in Composite Laminates Using Plate Elements10.2514/3.13038 ↗
30. A Shell/3D Modeling Technique for the Analysis of Delaminated Composite Laminates10.1016/S1359-835X(00)00133-0 ↗
31. Krüeger, R., Mingüet, P. J., and O’Brien, T. K., 2003, “Implementation of Interlaminar Fracture Mechanics in Design: An Overview,” 14th International Conference on Composite Materials (ICCM-14), San Diego.