Methodology for Determining the Variance of the Taylor Factor: Application in Fe-3%Si
Source abstract
Abstract
Abstract A method is proposed to determine the variance of an arbitrary material property based on the statistics of the texture of polycrystalline materials for a specified volume. This method is applied to determine the variance of the Taylor factor (i.e., measure of plastic deformation in crystal plasticity) and is compared to a random sampling method. The results from the random sampling method correlated well with the statistical variance relationship when the magnitude of the variance was greater than that of the numerical errors observed in the statistical calculation. An empirical relation was also shown to model the results, and the constants for this relationship were determined for pseudo-three-dimensional Fe-3%Si. Implementation of the statistical variance relationship in true three-dimensional microstructures is not limited by material opacity, since it depends only on the two-point pair correlation functions. The connection between the variance of the R-value and variance of the Taylor factor is considered. Although only a weak connection was found, it was observed that relatively small variations in the Taylor factor yield large variances in the R-value.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fatigue and fracture mechanics · Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Dept. of Mat. Sci. and Eng., Georgia Institute of Technology, 771 Ferst Drive, Atlanta, Georgia 30332-0245
Dept. of Mech. Eng., Brigham Young University, 435 CTB, Provo, UT 84602
Manufacturing and Eng. Technology, Brigham Young University, 265 CTB, Provo, UT 84602
References (39)
Show source-provided references
1. Methodology for Recovering and Analyzing Two-Point Pair Correlation Functions in Polycrystalline Materials
2. Material Spatial Randomness: From Statistical to Representative Volume Element10.1016/j.probengmech.2005.07.007 ↗
3. Determination of the Size of the Representative Volume Element for Random Composites: Statistical and Numerical Approach10.1016/S0020-7683(03)00143-4 ↗
4. Bunge
5. Bunge, H. J. , 1982, “Mean Values of Physical Properties,” Quantitative Texture Analysis, pp. 383–406.
6. Randle10.1201/9781003423980 ↗
7. Orientation Imaging: The Emergence of a New Microscopy
8. Orientation Imaging Microscopy: Application to the Measurement of Grain Boundary Structure10.1016/0921-5093(93)90310-B ↗
9. Microtexture Determination by Electron Backscatter Diffraction10.1007/BF01165988 ↗
10. Use of Microstructural Statistics in Predicting Polycrystalline Material Properties10.1007/s11661-999-0150-5 ↗
11. Influence of Grain Size on Plastic Anisotropy in Low Carbon Steels10.1179/mst.1986.2.4.354 ↗
12. Skrotzki, B., StarkeJr., E. A., and Shiflet, G. J., 1994, “Effect of Texture and Precipitates on Mechanical Property Anisotropy of Al-Cu-Mg-X Alloys,” In The 4th International Conference on Aluminum Alloys: Their Physical and Mechanical Properties, 2, pp. 40–47.
13. Texture Clustering and Long-rang Disorientation Representation Methods: Application to 6022 Aluminum Sheet10.1007/s11661-002-0243-x ↗
14. Variance of the Grain Boundary Character Distribution10.4028/www.scientific.net/MSF.495-497.871 ↗
15. Local Volume Fraction Fluctuations in Heterogeneous Media10.1063/1.457857 ↗
16. Local Volume Fraction Fluctuations in Random Media10.1063/1.477843 ↗
17. Recent Studies of Local Texture and Its Influence on Failure10.1016/S0921-5093(98)00835-1 ↗
18. Measurement of Normal Plastic Anisotropy in Sheet Metal
19. On the R-value Measurements10.1007/BF02659867 ↗
20. A Method for Determining Property Variance in Polycrystalline Materials
21. Morawiec10.1007/978-3-662-09156-2 ↗
22. Prediction of Elastic Constants of Multiphase Materials
23. The Elastic Behavior of a Crystalline Aggregate10.1088/0370-1298/65/5/307 ↗
24. Berechnung der Fliessgrenze von Mischkristallen auf Grund der Plastizitätsbedingung für Einkristalle10.1002/zamm.19290090104 ↗
25. Voigt10.1007/978-3-663-15884-4 ↗
26. The Relation Between Polycrystal Deformation and Single-Crystal Deformation10.1007/BF02900224 ↗
27. Bishop · Philos. Mag. · 42 · 41410.1080/14786445108561065 ↗
28. Bishop · Philos. Mag. · 42 · 129810.1080/14786444108561385 ↗
29. Macroscopic Response of Continua with Random Microstructures
30. Kroner10.1007/978-3-7091-2862-6 ↗
31. Constraints on Microstructural Two-point Correlation Functions10.1016/j.scriptamat.2005.06.013 ↗
32. Torquato
33. Generalization and Equivalence of the Minimum Work (Taylor) and Maximum Work (Bishop-Hill) Principles for Crystal Plasticity
34. Computer Solutions of the Taylor Analysis for Axisymmetric Flow
35. Plastic Strain in Metals
36. Bounds and Self-consistent Estimates for Creep of Polycrystalline Materials
37. New Criteria for Predicting the Press Performance of Deep Drawing Sheets
38. Hosford
39. Prediction of Macroscopic Anisotropy in Rolled Aluminum-Lithium Sheet10.1016/S1359-6462(99)00241-9 ↗