Effect of Yield Criterion on Numerical Simulation Results Using a Stress-Based Failure Criterion
Source abstract
Abstract
Determining tearing concerns in numerical simulations of sheet metal components is difficult since the traditional failure criterion, which is strain-based, exhibits a strain path dependence. A stress-based, as opposed to a strain-based, failure criterion has been proposed and demonstrated analytically, experimentally in tube forming, and through numerical simulations. The next step in this progression to the acceptance of a stress-based forming limit diagram is to demonstrate how this failure criterion can be used to predict failure of sheet metal parts in numerical simulations. In this paper, numerical simulation results for dome height specimens are presented and compared to experimental data. This procedure was repeated for various yield criteria to examine the effect of this parameter on the ability to predict failure in the numerical simulations. Reasonable agreement was obtained comparing the failure predicted from numerical simulations and those found experimentally, in particular for the yield criterion which has been shown to best characterize the material used in this study.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mechanical Engineering Department, University of New Hampshire, 33 College Road, Durham, NH 03824-3591
References (23)
Show source-provided references
1. Keeler, S. P. , 1966, “Determination of Forming Limits in Automotive Stampings,” Transactions of Society of Automotive Engineers, Paper No. 650355.10.4271/650535 ↗
2. Goodwin, G. M. , 1968, “Application of Strain Analysis to Sheet Metal Forming Problems in the Press Shop,” Transactions of Society of Automotive Engineers, Paper No. 680093.10.4271/680093 ↗
3. Effect of Changing Strain Paths of Forming Limit Diagrams of Al 2008-T4
4. Effects of Strain Path Changes on the Formability of Sheet Metals10.1007/BF02663419 ↗
5. Determination of the Forming Limit Stress Curve for Anisotropic Sheets10.1016/S0007-8506(07)62584-0 ↗
6. Gese, H., Dell, H., Kebler, L., Hooputra, H., and Werner, H., 2001, “Continuous Failure Prediction Model for Non Linear Load Paths in Successive Stamping and Crash Processes,” Transactions of Society of Automotive Engineers, Paper No. 2001-01-1131.
7. Limit Strains in the Processes of Stretch Forming Sheet Steel10.1016/0020-7403(67)90066-5 ↗
8. Neck Growth and Forming Limits in Sheet Metals10.1016/0020-7403(82)90035-2 ↗
9. Effects of Plastic Anisotropic and Yield Surface Shape on Sheet Metal Stretchability
10. Stress-Based Forming Limits in Sheet-Metal Forming10.1115/1.1398083 ↗
11. Stoughton, T. B. , 2002, “The Influence of the Material Model on the Stress-based Forming Limit Criterion,” SAE Paper No. 2002-01-0157.10.4271/2002-01-0157 ↗
12. Characterization and Modeling of the Mechanical Behaviour and Formability of a 2008-T4 Sheet Sample10.1016/0020-7403(89)90104-5 ↗
13. A Theory of the Yielding and Plastic Flow of Anisotropic Metals
14. Statistical Evaluation of the Uncertainty of Experimentally Characterised Forming Limits of Sheet Metal10.1016/S0924-0136(00)00890-6 ↗
15. Upper-Bound Anisotropic Yield Locus Calculations Assuming ⟨111⟩ Pencil Glide10.1016/0020-7403(80)90011-9 ↗
16. Use of Two Behaviour Laws for the Determination of the Forming Limit Stress Diagram of a Thin Steel Sheet10.1016/S0924-0136(00)00637-3 ↗
17. On Forming Limit Stress Diagram Analysis10.1016/j.ijsolstr.2004.09.010 ↗
18. Review of Theoretical Models of the Strain-Based FLD and their Relevance to the Stress-Based FLD10.1016/j.ijplas.2003.11.004 ↗
19. Experimental Verification of the Path-Independence of Forming Limit Stresses
20. Evaluation of Cruciform Specimens for Stress-Based Forming Limit Diagram Validation
21. Moondra, S. , 2004, “Numerical Simulation Investigations to Support a Stress-Based Failure Criterion for Sheet Metal Forming,” Master’s thesis, University of New Hampshire, Durham.10.1115/IMECE2005-80317 ↗
22. Formability of Stainless steel
23. Kinsey, B., and Sakash, A., 2006, “Evaluation of Stress Saturation Effect with a Stress-Based Failure Criterion for Sheet Metal Using Numerical Simulations,” Transactions of Society of Automotive Engineers, Paper No. 06M-213.10.4271/2006-01-0350 ↗