journal article·2003-07-01

Measurement of Thickness-Average Residual Stress Near the Edge of a Thin Laser Peened Strip

Jon E. Rankin, Michael R. Hill

Publisher page

Abstract

This paper presents measurements of the thickness-average residual stress imposed by laser peening near the edge of a thin sheet of a common titanium alloy. The slitting (or crack compliance) method was extended beyond its typical form to make residual stress measurements in this geometry. An analytical method was employed to optimize the experiment design for the near-edge, thin material geometry, where the design included the optimal number and position of strain gages and the most effective set of basis functions for stress computation. Two experiments were performed on a titanium strip that had been laser peened near the edge, using an optimal experiment design. Residual stress was found to be large and compressive near the edge of the sheet, with the compressive stress extending over 38% of the laser peened area.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Advanced Surface Polishing Techniques · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Mechanical and Aeronautical Engineering Department, University of California, Davis, CA

References (11)

Show source-provided references
1. Smith, P. R., Shepard, M. J., Preve´y, P. S., and Clauer, A. H., 2000, “Effect of Power Density and Pulse Repetition on Laser Shock Peening of Ti-6Al-4V,” J. Mater. Eng. Perform., 9(1), pp. 33–37.10.1361/105994900770346259 ↗
2. Prime, M. B. , 1999, “Residual Stress Measurement by Successive Extension of a Slot: The Crack Compliance Method,” Appl. Mech. Rev., 52(2), pp. 75–96.10.1115/1.3098926 ↗
3. Hill, M. R., and Lin, W., 2002, “Residual Stress Measurement in a Ceramic-Metallic Graded Material,” ASME J. Eng. Mater. Technol., 124(2), pp. 185–191.10.1115/1.1446073 ↗
4. Dane, C. B., Zapata, L. E., Neuman, W. A., Norton, M. A., and Hackel, L. A., 1995, “Design and Operation of a 150 W Near Diffraction-Limited Laser Amplifier With SBS Wavefront Correction,” IEEE J. Quantum Electron., 31(1), pp. 148–163.10.1109/3.341719 ↗
5. Hammersley, G., Hackel, L. A., and Harris, F., 2000, “Surface Prestressing to Improve Fatigue Strength of Components by Laser Shot Peening,” Opt. Lasers Eng., 34(4–6), pp. 327–337.10.1016/S0143-8166(00)00083-X ↗
6. Campbell, S. L., and Meyer, C. D., Jr., 1979, Generalized Inverses of Linear Transformations, Pitman Publishing Limited, London, pp. 8–27.
7. Greenberg, M. D., 1978, Foundations of Applied Mathematics, Prentice-Hall, Englewood Cliffs, NJ, p. 21.
8. Strang, G., 1986, Introduction to Applied Mathematics, Wellesley-Cambridge Press, Wellesley, MA, pp. 460–461.
9. Cheng, W., Finnie, I., Gremaud, M., and Prime, M. B., 1994, “Measurement of Near Surface Residual Stresses Using Electrical Discharge Wire Machining,” ASME J. Eng. Mater. Technol., 116, pp. 1–7.10.1115/1.2904251 ↗
10. Moore, M. G., and Evans, W. P., 1958, “Correction of Stress Layers in X-Ray Diffraction Residual Stress Analysis,” SAE Trans., 66, pp. 340–345.10.4271/580035 ↗
11. Boyer, R., Welsch, G., and Collings, E. W., eds., 1994, Materials Properties Handbook: Titanium Alloys, ASM International, Materials Park, OH, p. 517.