journal article·2012-10-01

Comparison Between Two Experimental Procedures for Cyclic Plastic Characterization of High Strength Steel Sheets

G. B. Broggiato, F. Campana, L. Cortese, E. Mancini

Publisher page

Abstract

In finite element analysis of sheet metal forming the use of combined isotropic-kinematic hardening models is advisable to improve stamping simulation and springback prediction. This choice becomes compulsory to model recent materials such as high strength steels. Cyclic tests are strictly required to evaluate the parameters of these constitutive models. However, for sheet metal specimens, in case of simple axial tension-compression tests, buckling occurrence during compression represents a serious drawback. This is the reason why alternative set-ups have been devised. In this paper, two experimental arrangements (a cyclic laterally constrained tension-compression test and a three-point fully reversed bending test) are compared so as to point out the advantages and the disadvantages of their application in tuning the well-known Chaboche’s hardening model. In particular, for tension-compression tests, a new clamping device was specifically designed to inhibit compressive instability. Four high strength steel grades were tested: two dual phases (DP), one transformation induced plasticity (TRIP) and one high strength low alloy material (HSLA). Then, the Chaboche’s model was calibrated through inverse identification methods or by means of analytical expressions when possible. The proposed testing procedure proved to be successful in all investigated materials. The achieved constitutive parameters, obtained independently from the two experimental techniques, were found to be consistent. Their accuracy was also been assessed by applying the parameter set obtained from one test to simulate the other one, and vice versa. Clues on what method provides the better transferability are given.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

e-mail:

e-mail: Dipartimento di Ingegneria Meccanica e Aerospaziale, “Sapienza” Università di Roma, Via Eudossiana, 18 – 00184 Rome, Italy

References (45)

Show source-provided references
1. The Formability of Dual-Phase Steels10.1007/BF02834208 ↗
2. Besdo, D., 2000, “On Numerical Problems With the Simulation of the Spring Back Phase of Sheet Metal Forming Process,” Plastic and Viscoplastic Response of Materials and Metal Forming: Proceedings of Plasticity ’00, the Eighth International Symposium on Plasticity and its Current Applications, Whistler, Canada July 16–20, A. S.Khan, H.Zhang, and Y.Yuan, eds., NEAT Press, Fulton, MD, pp. 17–19.
3. Formability Performance Comparison Between Dual Phase and HSLA Steels
4. Simulation of Springback in V-Bending Process by Elasto-Plastic Finite Element Method With Consideration of Bauschinger Effect10.1007/BF03187783 ↗
5. FE Analysis of Springback in Hat-Bending With Consideration of Initial Anisotropy and the Bauschinger Effect
6. Numerical Modeling Technique for Tailor Welded Blanks
7. Simulation of Springback10.1016/S0020-7403(01)00083-2 ↗
8. On Stress-Strain Relations Suitable for Cyclic and Other Loadings10.1115/1.3157660 ↗
9. The Bauschinger Effect of Sheet Metal Under Cyclic Reverse Pure Bending10.1016/S0007-8506(07)61638-2 ↗
10. Elastic-Plastic Behavior of Steel Sheets Under In-Plane Cyclic Tension-Compression at Large Strain
11. A Model of Large-Strain Cyclic Plasticity Describing the Bauschinger Effect and Workhardening Stagnation10.1016/S0749-6419(01)00050-X ↗
12. Work-Hardening Behavior of Mild Steel Under Stress Reversal at Large Strains10.1016/0749-6419(92)90006-X ↗
13. Investigation of Advanced Strain-Path Dependent Material Models for Sheet Metal Forming Simulations10.1016/j.ijplas.2006.10.004 ↗
14. On the Modeling of the Bending-Unbending Behavior for Accurate Springback Predictions10.1016/j.ijmecsci.2009.05.007 ↗
15. Modeling the Bauschinger Effect for Sheet Metals, Part I: Theory
16. A New Method of Analyzing Stresses and Strains in Work-Hardening Plastic Solids10.1115/1.4011389 ↗
17. A Modification of Prager’s Hardening Rule
18. A Mathematical Representation of the Multiaxial Bauschinger Effect
19. Time-Independent Constitutive Theories for Cyclic Plasticity10.1016/0749-6419(86)90010-0 ↗
20. Constitutive Equations for Cyclic Plasticty and Cyclic Viscoplasticity10.1016/0749-6419(89)90015-6 ↗
21. On the Description of Anisotropic Work Hardening10.1016/0022-5096(67)90030-0 ↗
22. On Generalized Kinematic Hardening Rule With Memory of Maximal Prestress
23. A Model for Nonlinearly Hardening Materials for Complex Loading10.1007/BF01181053 ↗
24. Simple Plasticity Model of Two Surface Type
25. A Two Surface Model for Transient Nonproportional Cyclic Plasticity—Part I: Development of Appropriate Equations10.1115/1.3169044 ↗
26. A Two Surface Model for Transient Nonproportional Cyclic Plasticity—Part II: Comparison of Theory With Experiments10.1115/1.3169045 ↗
27. Evaluation of Intersection Conditions for Two Surface Plasticity Theory10.1016/0749-6419(89)90018-1 ↗
28. Springback Analysis With a Modified Hardening Model
29. Modeling the Bauschinger Effect for Sheet Metals, Part II: Applications
30. A Model of Large-Strain Cyclic Plasticity and Its Application to Springback Simulation10.1016/j.ijmecsci.2003.10.013 ↗
31. Continuous Large Strain, Tension/Compression Testing of Sheet Material10.1016/j.ijplas.2004.12.002 ↗
32. Identification of Material Hardening Parameters by Three-Point Bending of Metal Sheets10.1016/j.ijmecsci.2006.05.009 ↗
33. Finite Element Analysis of the Three-Point Bending of Sheet Metals10.1016/S0924-0136(01)01064-0 ↗
34. An Efficient Inverse Approach for Material Hardening Parameter Identification From a Three-Point Bending Test10.1007/s00366-009-0149-y ↗
35. Cold Plastic Formability of Metals: FEM Modelling and Optimization of Material Models
36. Spring-Back Evaluation of Automotive Sheets Based on Isotropic-Kinematic Hardening Laws and Non-Quadratic Anisotropic Yield Functions, Part III: Applications10.1016/j.ijplas.2004.05.014 ↗
37. Finite Element Analysis of High Strength Steel Stamping Process Adopting a Combined Isotropic-Kinematic Hardening Model: Experimental Investigation of the Improvements Achieved in Springback Prevision
38. Work-Hardening Behavior of Mild Steel Under Cyclic Deformation at Finite Strains10.1016/0956-7151(94)90480-4 ↗
39. The Chaboche Nonlinear Kinematic Hardening Model: Calibration Methodology and Validation10.1007/s11012-008-9115-9 ↗
40. Tensile-Shear Forces and Fracture Modes in Single and Multiple Weld Specimens in Dual-Phase Steels10.1115/1.2137751 ↗
41. Tensile Deformation and Fracture of TRIP590 Steel From Digital Image Correlation
42. An Efficient and Effective Methodology and Simulation Tools for Die Design and Springback Compensation for HSS and UHSS, ‘SPRINCOM
43. 1995
44. Campana, F., Cortese, L., and Placidi, F., 2005, “FEM Evaluation of Springback After Sheet Metal Forming: Application to High Strength Steels of a Combined Isotropic-Kinematic Hardening Model,” 1st International Conference on Super High Strength Steels, Nov. 2–4, Rome, Italy.
45. Parameter Identification for No Linear Costitutive Models: Finite Element Simulation, Optimization, Nontrivial Experiments