journal article·2011-04-01Open access

The Impact of Weld Metal Creep Strength on the Overall Creep Strength of 9% Cr Steel Weldments

Peter Mayr, Stefan Mitsche, Horst Cerjak, Samuel M. Allen

Abstract

In this work, three joints of a X11CrMoWVNb9-1-1 (P911) pipe were welded with three filler metals by conventional arc welding. The filler metals varied in creep strength level, so that one overmatched, one undermatched, and one matched the creep strength of the P911 grade pipe base material. The long-term objective of this work was to study the influence of weld metal creep strength on the overall creep behavior of the welded joints and their failure mechanism. Uniaxial creep tests at 600°C and stresses ranging from 70 MPa to 150 MPa were performed on the cross-weld samples of all three welds. A total creep testing time of more than 470,000 h was accumulated. The longest running sample achieved a time-to-rupture of more than 45,000 h. Creep testing revealed that the use of undermatching weld metal led to a premature fracture in the weld metal at higher stress levels. Compared with undermatching weld metal, the use of matching and overmatching filler materials increased the time-to-rupture at high stress levels by 75% and 33% at lowest stress levels. At typical component stresses below 100 MPa, all samples failed in the grain-refined heat-affected zone by characteristic type IV failure. For investigations of the failure modes, cross sections of fractured samples were investigated by optical light microscopy, scanning electron microscopy, and electron backscatter diffraction. The mechanism of weld metal creep failures and type IV creep failures is discussed in detail.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139; Institute for Materials Science and Welding, Graz University of Technology, Kopernikusgasse 24, 8010 Graz, Austria

Institute for Electron Microscopy and Fine Structure Research, Graz University of Technology, Steyrergasse 17, 8010 Graz, Austria

Institute for Materials Science and Welding, Graz University of Technology, Kopernikusgasse 24, 8010 Graz, Austria

Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139

References (15)

Show source-provided references
1. UK Experience With Modified 9Cr (Grade 91) Steed
2. Evaluation of Creep Strength Reduction Factors for Welded Joints of Modified 9CR-1MO Steel (P91)10.1115/PVP2006-ICPVT-11-93350 ↗
3. Risse Im Schweissnahtbereich Von Formstuecken Aus Heissdampfleitungen-Werkstoffuntersuchungen
4. Type IV Cracking in Ferritic Power Plant Steels10.1179/174328406X148778 ↗
5. Type IV Creep Cavity Accumulation and Failure in Steel Welds10.1016/S0308-0161(03)00134-0 ↗
6. Stress-Strain Analysis of Creep Deterioration in Heat Affected Weld Zone in High Cr Ferritic Heat Resistant Steel10.1179/026708303225005926 ↗
7. Microstructure and Creep Strength of Welds in Advanced Ferritic Power Plant Steels10.1179/136217104225017107 ↗
8. Investigations on the High Temperature Behaviour of Welded Martensitic Joints10.1016/j.engfracmech.2010.03.046 ↗
9. On the Relaxation of Interface Stresses During Creep of Ferritic Steel Weldments10.1243/0309324981512913 ↗
10. Microstructural Change of 9% Cr-Welded Joints After Long-Term Creep10.1016/j.msea.2009.10.044 ↗
11. 2005, “ECCC Datasheets-GX12CrMoVNbN9-1, X11CrMoWVNb9-1-1, ASTM Grade 92,” European Creep Collaborative Committee-Working Group 3A.
12. 2005, “Weld Consumable Datasheets-Thermanit MTS3, Thermanit Chromo 9V, Thermanit MTS 616, Thermanit MTS 911,” Böhler Schweißtechnik Deutschland.
13. Long-Term Creep Behaviour of E911 Heat Resistant 9% Cr Steel Weldments Fabricated With Filler Metals of Different Creep Strength
14. Klenk, A., and Buchmayr, B., 2005, “ECCC Recommendations-Volume 3 Part II-Data Acceptability Criteria and Data Generation: Creep Data of Welds,” European Creep Collaborative Committee.
15. Kassner