Investigation of the Microstructural Evolution During Large Strain Cold Working of Metals by Means of Synchrotron Radiation—A Comparative Overview
Source abstract
Abstract
Dislocation densities, arrangements and long range internal stresses in cold rolled polycrystalline Cu, Ni, and Al, as well as in cold torsioned Fe, were determined by X-ray diffraction profile analysis using synchrotron radiation. At different deformation degrees, scanning measurements across single grains with a focal spot of less than 50 μm were carried out, in order to inform on the features of the deformation induced substructure. At small deformations including stage III, the dislocation densities and internal stresses are uniform within single grains while at higher deformations in stages IV and V, the dislocation densities and long range internal stresses exhibit opposite fluctuations. In stage IV these fluctuations correspond to the formation of polarized tilt walls (PTW’s) from polarized dipole walls (PDW’s). In contrast to the PDW’s, the PTW’s cause a much higher misorientation in between adjacent lattice areas. This transformation, which is the main element of the progressing fragmentation process during large strain deformation, occurs in all metals studied regardless of dislocation mobility and/or lattice type. Approaching higher strains in stage V, however, these parameters gain some importance especially when the deformation occurs in an iterative way. If the mobility is high, marked static recovery takes place between the single deformation passes, which results in decreases of both dislocation density and local internal stress, and no formation of PTW’s is observed.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Institute of Materials Physics, University of Vienna, A-1090 Wien, Strudlhofgasse 4, Austria
Department of General Physics, Eo¨tvo¨s University Budapest, H-1518 Budapest, Pazmany Peter Setany 1/A, Hungary
Sincrotrone ELETTRA, I-34012 Trieste, Basovizza, Italy
References (32)
Show source-provided references
1. Mughrabi, H. , 1983, “Dislocation wall and cell structures and long range internal stresses in deformed metal crystals,” Acta Metall. 31, pp. 1367–1379.10.1016/0001-6160(83)90007-X ↗
2. Gil Sevillano, J., Van Houtte, P., and Aernoudt, E., 1980, “Large strain work hardening and textures,” Prog. Mater. Sci. 25, pp. 69–412.10.1016/0079-6425(80)90001-8 ↗
3. Hansen, N. , 1990, “Cold deformation microstructures,” Mater. Sci. Technol. 6, 1039–1047.10.1179/026708390790189993 ↗
4. Unga´r, T., Mughrabi, H., and Wilkens, M., 1982, “An X-ray line-broadening study of dislocations near the surface and in the bulk of deformed copper single crystals,” Acta Metall. 30, pp. 1861–1867.10.1016/0001-6160(82)90026-8 ↗
5. Unga´r, T., Mughrabi, H., Ro¨nnpagel, D., and Wilkens, M., 1984, “X-ray line broadening study of the dislocation cell structure in deformed [001]-orientated copper single crystals,” Acta Metall. 32, pp. 333–342.10.1016/0001-6160(84)90106-8 ↗
6. Unga´r, T., and Zehetbauer, M., 1996, “Stage IV work hardening in cell forming materials, pt. II: A new mechanism,” Scr. Mater. 35, pp. 1467–1473.10.1016/S1359-6462(96)00320-X ↗
7. Schafler, E., Zehetbauer, M., Borbely, A., and Unga´r, T., 1997 “Dislocation densities and internal stresses in large strain cold worked pure iron,” Mater. Sci. Eng., A 234–236, 445–448.10.1016/S0921-5093(97)00168-8 ↗
8. Kuhlmann-Wilsdorf, D., and Hansen, N., 1991, “Geometrically necessary, incidental and subgrain boundaries,” Scr. Metall. Mater. 25, pp. 1557–1562.10.1016/0956-716X(91)90451-6 ↗
9. Hughes D. A., 1995, “The evolution of deformation microstructures and local orientations,” Proc. 19th Int. Symp. Mater. Sci., Hansen, N. et al., eds., Riso National Laboratory, Roskilde, Denmark, pp. 63–85.
10. Zehetbauer, M., and Seumer, V., 1993, “Cold work hardening in stages IV and V of f.c.c. metals –I. Experiments and interpretation,” Acta Metall. Mater. 41, pp. 577–588.10.1016/0956-7151(93)90088-A ↗
11. Les, H. P., Stu¨we, H. P., and Zehetbauer, M., 1997, “Hardening and strain rate sensitivity in stage IV of deformation in f.c.c. and b.c.c. metals,” Mater. Sci. Eng., A 234–236, pp. 453–455.10.1016/S0921-5093(97)00259-1 ↗
12. Rollett, A. D., Kocks, U. F., Embury, J. D., Stout, M. G., and Doherty, R. D., 1987, “Strain hardening at large strains,” Proc. 8th Int.Conf.Strength Met. & Alloys (ICSMA 8), Tampere, Finland, Kettunen, P.O. et al., eds., Pergamon, Oxford, p. 433–438.10.1016/B978-0-08-034804-9.50065-6 ↗
13. Argon, A. S., and Haasen, P., 1993, “A new mechanism of work hardening in the late stages of large strain plastic flow in fcc and diamond cubic crystals,” Acta Metall. Mater. 41, pp. 3289–3306.10.1016/0956-7151(93)90058-Z ↗
14. Zehetbauer, M. , 1993, “Cold work hardening in stages IV and V of fcc metals-II. model fits and physical results,” Acta Metall. Mater. 41, pp. 589–599.10.1016/0956-7151(93)90089-B ↗
15. Marthinsen, K., and Nes, E., 1997, “A general model for metal plasticity,” Mater. Sci. Eng., A 234–236, pp. 1095–1098.10.1016/S0921-5093(97)00349-3 ↗
16. Estrin, Y., Toth, L. S., Molinari, A., and Brechet, Y., 1998, “A dislocation-based model for all hardening stages in large strain deformation,” Acta Mater. 46, pp. 5509–5522.10.1016/S1359-6454(98)00196-7 ↗
17. Valiev, R. Z., Islamgaliev, R. K., and Alexandrov, I. V., 2000, “Bulk Nanostructured Materials from Severe Plastic Deformationation,” Prog. Mater. Sci. 45, pp. 103–189.10.1016/S0079-6425(99)00007-9 ↗
18. Wilkens, M., and Bargouth, M. O., 1968, “Die Bestimmung der Versetzungsdichte verformter Kupfer-Einkristalle aus verbreiterten Ro¨ntgenbeugungsprofilen,”Acta Metall. 16, pp. 465–468.10.1016/0001-6160(68)90032-1 ↗
19. Oettel, H. , 1971, “X-ray analysis of dislocation densities and resistivity changes of plastically deformed fcc Ni-Co alloys,” Phys. Status Solidi A 6, 265–272.10.1002/pssa.2210060130 ↗
20. Groma, I., Unga´r, T., and Wilkens, M., 1988, “Asymmetric X-ray line broadening of plastically deformed crystals. Theory,” J. Appl. Cryst 21, pp. 47–53.10.1107/S0021889887009178 ↗
21. Unga´r, T., Groma, I., and Wilkens, M., 1989, “Asymmetric X- ray line broadening of plastically deformed crystals. II. Evaluation procedure and application to [001]-Cu Crystals,” J. Appl. Crystallogr. 22, pp. 226–34.10.1107/S0021889888009720 ↗
22. Mu¨ller, M., Zehetbauer, M., Borbe´ly, A., and Unga´r, T., 1996, “Stage IV work hardening in cell forming materials, Part I: Features of the dislocation structure determined by X-ray line broadening,” Scr. Metall. Mater. 35, pp. 1461–1466.10.1016/S1359-6462(96)00319-3 ↗
23. Zehetbauer, M., Unga´r, T., Kral, R., Borbely, A., Schafler, E., Ortner, B., Amenitsch, H., and Bernstorff, S., 1999, “Scanning X-ray diffraction peak profile analysis in deformed Cu-polycrystals by synchrotron radiation,” Acta Mater. 47, pp. 1053–1061.10.1016/S1359-6454(98)00366-8 ↗
24. Schafler, E., Zehetbauer, M., Kopacz, I., Unga´r, T., Hanak, P., Amenitsch, H., and Bernstorff, S., 1999, “Microstructural parameters in large strain deformed Ni polycrystals as investigated by synchrotron radiation,” Phys. Status Solidi A 175, pp. 501–511.10.1002/(SICI)1521-396X(199910)175:2<501::AID-PSSA501>3.0.CO;2-A ↗
25. Schafler, E., Zehetbauer, M., Hanak, P., Unga´r, T., Hebesberger, T., Pippan, R., Mingler, B., Karnthaler, H.P., Amenitsch, H., and Bernstorff, S., 2000, “Fragmentation in large strain cold rolled Aluminum as observed by synchrotron X-ray Bragg Peak Profile Analysis (SXPA), Electron Back Scatter Patterning (EBSP) and Transmission Electron Microscopy (TEM),” Proc. NATO Advanced Research Workshop “Investigations and Applications of Severe Plastic Deformation”, Moscow, 1999, Russia, T. C. Lowe and R. Z. Valiev, eds., Kluwer Acad. Publ., pp. 163–171.10.1007/978-94-011-4062-1_22 ↗
26. Schafler, E., Zehetbauer, M., Unga´r, T., Bernstorff, S., and Amenitsch, H., 2000, “Microscale Spatial Distribution of Dislocations and Long Range Internal Stresses in Cold Worked bcc Fe,” Proc. 5th Asia Pacific Symposium on Advances in Engineering Plasticity & Applications (AEPA 2000), Hong-Kong, Key Eng. Mater. 177–180, pp. 159–164.10.4028/www.scientific.net/KEM.177-180.159 ↗
27. Hebesberger, T., Schafler, E., Zehetbauer, M., Pippan, R., Unga´r, T., and Bernstorff, S., 2001, “Electron Back Scatter Diffraction (EBSD) and Synchrotron X-Ray Profile Analysis (SXPA) as Tools for Microstructural Characterization of Large Strain Work Hardened Metals,” Z. Metallkd. 92, pp. 410–416.
28. Amenitsch, H., Bernstorff, S.and Laggner, P., 1995, “High Flux Beamline for Small Angle X-ray Scattering at ELETTRA,” Rev. Sci. Instrum. 66, pp. 1624–1626.10.1063/1.1145864 ↗
29. Wilkens, M. , 1970, “The determination of density and distribution of dislocations in deformed single crystals form broadened X-ray diffraction profiles,” Phys. Status Solidi A 2, pp. 359–370.10.1002/pssa.19700020224 ↗
30. Kocks, U. F., and Scattergood, R. O., 1969, “Elastic interactions between dislocations in a finite Body,” Acta Metall. 17, pp. 1161–1168.10.1016/0001-6160(69)90093-5 ↗
31. Wilkens, M., Herz, K., and Mughrabi, H., 1980, “An X-ray diffraction study of cyclically and of unidirectionally deformed copper single crystals,” Z. Metallkd. 71, pp. 376–384.10.1002/chin.198036008 ↗
32. Zehetbauer, M., and Trattner, D., 1987, “Effects of stress-aided static recovery in iteratively cold-worked aluminum and copper,” Mater. Sci. Eng. 89, pp. 93–101.10.1016/0025-5416(87)90253-9 ↗