Thermofluid Properties of Ti-6Al-4V Melt Pool in Powder-Bed Electron Beam Additive Manufacturing
Source abstract
Abstract
Electron beam additive manufacturing (EBAM) is a powder-bed fusion additive manufacturing (AM) technology that can make full density metallic components using a layer-by-layer fabrication method. To build each layer, the EBAM process includes powder spreading, preheating, melting, and solidification. The quality of the build part, process reliability, and energy efficiency depends typically on the thermal behavior, material properties, and heat source parameters involved in the EBAM process. Therefore, characterizing those properties and understanding the correlations among the process parameters are essential to evaluate the performance of the EBAM process. In this study, a three-dimensional computational fluid dynamics (CFD) model with Ti-6Al-4V powder was developed incorporating the temperature-dependent thermal properties and a moving conical volumetric heat source with Gaussian distribution to conduct the simulations of the EBAM process. The melt pool dynamics and its thermal behavior were investigated numerically, and results for temperature profile, melt pool geometry, cooling rate and variation in density, thermal conductivity, specific heat capacity, and enthalpy were obtained for several sets of electron beam specifications. Validation of the model was performed by comparing the simulation results with the experimental results for the size of the melt pool.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, University of New Orleans, 2000 Lakeshore Drive, New Orleans, LA 70148 e-mail:
Funding
National Science Foundation
References (56)
Show source-provided references
1. Thermographic Microstructure Monitoring in Electron Beam Additive Manufacturing10.1038/srep43554 ↗
2. The Metallurgy and Processing Science of Metal Additive Manufacturing10.1080/09506608.2015.1116649 ↗
3. Additive Manufacturing Methods and Modelling Approaches: A Critical Review10.1007/s00170-015-7576-2 ↗
4. Review on Powder-Based Electron Beam Additive Manufacturing Technology10.1051/mfreview/2014001 ↗
5. The Present and Future of Additive Manufacturing in the Aerospace Sector: A Review of Important Aspects10.1177/0954410014568797 ↗
6. Additive Fabrication Technologies Applied to Medicine and Health Care: A Review10.1007/s00170-007-1308-1 ↗
7. Designing, Prototyping and Manufacturing Medical Devices: An Overview10.1080/0951192X.2014.934292 ↗
8. Macroscopic Simulation and Experimental Measurement of Melt Pool Characteristics in Selective Electron Beam Melting of Ti-6Al-4V10.1007/s00170-016-8819-6 ↗
9. Gong, X., Cheng, B., Price, S., and Chou, K., “Powder-Bed Electron-Beam-Melting Additive Manufacturing: Powder Characterization, Process Simulation and Metrology,” Proceedings of the ASME Early Career Technical Conference, Birmingham, AL, Nov. 2–3, 2013.
10. Microstructural Architecture, Microstructures, and Mechanical Properties for a Nickel-Base Superalloy Fabricated by Electron Beam Melting10.1007/s11661-011-0748-2 ↗
11. Advanced Metal Powder Based Manufacturing of Complex Components by Electron Beam Melting10.1179/106678509X12475882446133 ↗
12. Characterization of H13 Steel Produced Via Electron Beam Melting10.1108/13552540410512516 ↗
13. Rodriguez, E., Medina, F., Espalin, D., Terrazas, C., Muse, D., Henry, C., MacDonald, E., and Wicker, R., “Integration of a Thermal Imaging Feedback Control System in Electron Beam Melting,” Proceedings From the Solid Freeform Fabrication Symposium, Austin, TX, Aug. 6–8, 2012.
14. A Three-Dimensional Finite Element Analysis of the Temperature Field During Laser Melting of Metal Powders in Additive Layer Manufacturing10.1016/j.ijmachtools.2009.07.004 ↗
15. Numerical Investigation of Residual Stress in Thick Titanium Alloy Plate Joined With Electron Beam Welding10.1007/s11663-010-9408-y ↗
16. An Analytical Model and Tomographic Calculation of Vacuum Electron Beam Welding Heat Source10.1016/j.vacuum.2009.11.015 ↗
17. Numerical Simulation of the Electron Beam Welding Process10.1016/j.compstruc.2011.01.016 ↗
18. Estimation of the Parameters of a Gaussian Heat Source by the Levenberg–Marquardt Method: Application to the Electron Beam Welding10.1016/j.ijthermalsci.2006.04.015 ↗
19. Prediction of Penetration Depths During Electron Beam Welding10.1179/136217199101537815 ↗
20. Optimization of the LENS Process for Steady Molten Pool Size10.1016/j.msea.2007.04.119 ↗
21. A Model for Estimating Penetration Depth of Laser Welding Processes10.1088/0022-3727/29/7/018 ↗
22. Numerical Simulation of Heat Transfer and Fluid Flow in Coaxial Laser Cladding Process for Direct Metal Deposition10.1063/1.2209807 ↗
23. Modeling of Transport Phenomena During the Coaxial Laser Direct Deposition Process10.1063/1.3474655 ↗
24. Modeling and Experiments of Laser Cladding With Droplet Injection10.1115/1.2005273 ↗
25. Numerical Simulation of Molten Pool Dynamics in High Power Disk Laser Welding10.1016/j.jmatprotec.2011.09.011 ↗
26. Residual Stress and Distortion Calculation of Laser Beam Welding for Aluminum Lap Joints10.1016/j.jmatprotec.2007.07.013 ↗
27. Numerical Simulation of Transient Temperature Field During Laser Keyhole Welding of 304 Stainless Steel Sheet10.1016/j.optlastec.2010.10.007 ↗
28. On Process Temperature in Powder-Bed Electron Beam Additive Manufacturing: Model Development and Validation10.1115/1.4028484 ↗
29. Shen, N., and Chou, K., 2012, “Thermal Modeling of Electron Beam Additive Manufacturing Process: Powder Sintering Effects,” Proceedings of the ASME Manufacturing Science and Engineering Conference, Notre Dame, IN, June 4–8, 2012.10.1115/MSEC2012-7253 ↗
30. The Effect of Electron Beam Energy Density on Temperature Field for Electron Beam Melting10.4028/www.scientific.net/AMR.900.631 ↗
31. Thermal Modeling of Laser Based Additive Manufacturing Processes Within Common Materials10.1016/j.promfg.2015.09.012 ↗
32. Modelling and Simulation of Electron Beam Melting10.1007/s11740-009-0197-6 ↗
33. Finite Element Simulation of Laser Additive Melting and Solidification of Inconel 718 With Experimentally Tested Thermal Properties10.1016/j.finel.2017.07.002 ↗
34. Optimizing Quality of Additively Manufactured Inconel 718 Using Powder Bed Laser Melting Process10.1016/j.addma.2016.03.006 ↗
35. Effective Liquid Conductivity for Improved Simulation of Thermal Transport in Laser Beam Melting Powder Bed Technology10.1016/j.addma.2016.12.004 ↗
36. Heat Transfer and Fluid Flow During Electron Beam Welding of 304L Stainless Steel Alloy
37. A Three-Dimensional Numerical Model for a Convection-Diffusion Phase Change Process During Laser Melting of Ceramic Materials10.1016/j.ijheatmasstransfer.2004.07.024 ↗
38. Chahine, G. , 2011, “Application of Digital Engineering in the Development of a Bio-Adaptable Dental Implant,” Ph.D. thesis, Southern Methodist University, Dallas, TX.
39. Attar, E. , 2011, “Simulation of Selective Electron Beam Melting Processes,” Ph.D. thesis, University of Erlangen-Nürnberg, Germany.
40. Rahman, M. S., Schilling, P. J., Herrington, P. D., and Chakravarty, U. K., “Thermo-Fluid Characterizations of Ti-6Al-4V Melt Pool in Powder-Bed Electron Beam Additive Manufacturing,” Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Vol. 1, Advances in Aerospace Technology, Phoenix, AZ, Nov. 11–17, 2016.10.1115/IMECE2016-65854 ↗
41. Rahman, M. S., Schilling, P. J., Herrington, P. D., and Chakravarty, U. K., “Thermal Analysis of Electron Beam Additive Manufacturing Using Ti-6Al-4V Powder-Bed,” Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Vol. 1, Advances in Aerospace Technology, Tampa, FL, Nov. 3–9, 2017.10.1115/IMECE2017-71663 ↗
42. Rahman, M. S., Schilling, P. J., Herrington, P. D., and Chakravarty, U. K., “A Comparative Study Between Selective Laser Melting and Electron Beam Additive Manufacturing Based on Thermal Modeling,” Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Vol. 1, Advances in Aerospace Technology, Pittsburgh, PA, Nov. 9–15, 2018.10.1115/IMECE2018-86428 ↗
43. Jamshidinia, M., Kong, F., and Kovacevic, R., “Temperature Distribution and Fluid Flow Modeling of Electron Beam Melting® (EBM),” Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Vol. 7, Part D, Fluid and Heat Transfer, Houston, TX, Nov. 9–15, 2012.10.1115/IMECE2012-89440 ↗
44. Numerical Modeling of Heat Distribution in the Electron Beam Melting of Ti-6Al-4V10.1115/1.4025746 ↗
45. Experimental Investigation and 3D Finite Element Prediction of the Heat Affected Zone During Laser Assisted Machining of Ti-6Al-4V Alloy10.1016/j.jmatprotec.2010.08.007 ↗
46. Thermal Conductivity of Iron-Titanium Powders10.1021/je00042a001 ↗
47. The Prediction of the Emissivity and Thermal Conductivity of Powder Beds10.1080/02726350490501682a ↗
48. 3D FE Simulation for Temperature Evolution in the Selective Laser Sintering Process10.1016/j.ijmachtools.2003.10.019 ↗
49. Finite Element Analysis of Temperature Distribution in Single Metallic Powder Layer During Metal Laser Sintering10.1016/j.ijmachtools.2006.09.025 ↗
50. Thermal Expansion of Liquid Ti-6Al-4V Measured by Electrostatic Levitation10.1063/1.2349840 ↗
51. Mills · 2002 · 21110.1533/9781845690144.211 ↗
52. Arce, A. N. , 2012, “Thermal Modeling and Simulation of Electron Beam Melting for Rapid Prototyping on Ti6Al4V Alloys,” Ph.D. thesis, North Carolina State University, Raleigh, NC.
53. Thermal Analysis of Laser-Densified Dental Porcelain Bodies: Modeling and Experiments10.1115/1.1795812 ↗
54. Heat Transfer and Fluid Flow During Electron Beam Welding of 21Cr-6Ni-9Mn Steel and Ti-6Al-4V Alloy10.1088/0022-3727/42/2/025503 ↗
55. A Numerical Solution of the Stefan Problem With a Neumann-Type Boundary Condition by Enthalpy Method10.1016/S0096-3003(02)00846-9 ↗
56. High-Re Solutions for Incompressible Flow Using the Navier–Stokes Equations and a Multigrid Method10.1016/0021-9991(82)90058-4 ↗