The Rapid Cooling Effect on Microstructure of Nickel-Based Alloys Welding Joint
Source abstract
Abstract
Fusion welding of nickel-based alloys is often associated with coarse grains and severe segregation, which finally results in the increase of hot cracking susceptibility and poor mechanical properties. Conventional gas tungsten arc welding (GTAW) can aggravate these phenomena, which is mainly due to its high heat input and low cooling rate. In this paper, the cooling rate was enhanced by spraying liquid nitrogen during the welding process. Compared to conventional GTAW, the rapid cooling produced narrower heat affected zone (HAZ) width and more equiaxed grains in the fusion zone, thus higher hardness distribution was also achieved in this condition. In addition, γ′ phase exhibited a dispersed distribution, and segregation has been improved. The results show that the HAZ width is decreased by about 50%, and the fusion zone consisting of the finest equiaxed grains and the lowest segregation was obtained, when the heat sink located on one side 10 mm away from the weld centerline. Also, fine equiaxed grains and the dispersed distribution of γ′ phase could improve the grain boundary strength and reduce the incidence of liquid films along grain boundaries, contributing to prevent nickel-based alloys welding hot cracking from initiating.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China
School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China e-mail:
References (30)
Show source-provided references
1. 1993
2. 2009
3. 1990
4. Controlling Hot Cracking in Nickel-Based Inconel-718 Superalloy Cast Sheets During Tungsten Inert Gas Welding10.1016/j.jmatprotec.2015.03.031 ↗
5. Effect of Welding Parameters on Microstructure, Mechanical Properties and Hot Cracking Phenomenon in Udimet 520 Superalloy10.1016/j.matdes.2011.10.020 ↗
6. Laves Phase in Superalloy 718 Weld Metals10.1007/BF00271015 ↗
7. Control of Laves Phase in Inconel 718 GTA Welds With Current Pulsing10.1179/136217104225021788 ↗
8. Improvement in Stress Rupture Properties of Inconel 718 Gas Tungsten Arc Welds Using Current Pulsing10.1007/s10853-005-0590-2 ↗
9. Influence of Weld Cooling Rate on Microstructure and Mechanical Properties of Alloy 718 Weldments10.1007/s11661-008-9553-y ↗
10. The Formation and Control of Laves Phase in Superalloy 718 Welds10.1023/A:1018541915113 ↗
11. The Effect of Peak Temperature and Cooling Rate on the Susceptibility to Intergranular Corrosion of Alloy 690 by Laser Beam and Gas Tungsten Arc Welding10.1016/j.corsci.2009.01.002 ↗
12. Influence of Cooling Rate on the Development of Multiple Generations of γ′ Phase Precipitates in a Commercial Nickel Base Superalloy10.1016/j.matchar.2011.06.002 ↗
13. On the Role of Liquated γ′ Phase Precipitates in Weld Heat Affected Zone Microfissuring of a Nickel-Based Superalloy10.1016/j.msea.2005.04.034 ↗
14. Contribution of Constitutional Liquation of Gamma Prime Precipitate to Weld HAZ Cracking of Cast Inconel 738 Superalloy10.1016/j.scriptamat.2003.11.025 ↗
15. Correlation Between Thermal Parameters, Structures, Dendritic Spacing and Corrosion Behavior of Zn-Al Alloys With Columnar to Equiaxed Transition10.1016/j.jcrysgro.2007.11.169 ↗
16. Microstructural Modification of Austenitic Stainless Steels by Rapid Solidification10.1007/BF02645553 ↗
17. Grain Refinement and Hardness Distribution in Cryogenically Cooled Ferritic Stainless Steel Welds10.1016/j.matdes.2012.12.008 ↗
18. Comparative Evaluation of Grain Refinement in AISI 430 FSS Welds by Elemental Metal Powder Addition and Cryogenic Cooling10.1016/j.matdes.2011.09.066 ↗
19. Minimization of Heat-Affected Zone Size in Welded Ultra-Fine Grained Steel Under Cooling by Liquid Nitrogen During Laser Welding10.1016/j.msea.2006.03.024 ↗
20. Influence of In-Process Cooling on Tensile Behavior of Friction Stir Welded Joints of AA703910.1016/j.msea.2012.07.016 ↗
21. Microstructural Characterization of Liquid Nitrogen Cooled Alloy 718 Fusion Zone10.1016/j.jmatprotec.2014.07.022 ↗
22. Enhanced Mechanical Properties of Tungsten Inert Gas Welded AZ31 Magnesium Alloy Joint Using Two-Pass Friction Stir Processing With Rapid Cooling10.1016/j.msea.2016.01.009 ↗
23. Deformation Control During the Laser Welding of a Ti6Al4V Thin Plate Using a Synchronous Gas Cooling Method10.1016/j.matdes.2015.11.035 ↗
24. Effect of Online Rapid Cooling on Microstructure and Mechanical Properties of Friction Stir Welded Medium Carbon Steel10.1016/j.jmatprotec.2015.11.015 ↗
25. Heat Affected Zone Liquation Cracking in Electron Beam Welded Third Generation Nickel Base Superalloys10.1016/j.msea.2007.04.091 ↗
26. Intergranular Liquation Cracking in Heat Affected Zone of a Welded Nickel Based Superalloy in as Cast Condition10.1179/174328407X213323 ↗
27. The Relationship Between Grain Size and Microfissuring in Alloy 718
28. An Investigation of Heat-Affected Zone Hot Cracking in Alloy 80010.1007/BF03321363 ↗
29. The Search for Novel, Superhard Materials10.1116/1.581977 ↗
30. Influence of Solidification on the Microstructural Evolution of Nickel Base Weld Metal10.1016/0921-5093(95)09832-1 ↗