journal article·2021-01-01

On the High-Temperature Flow Response of Friction Stir Processed Magnesium Metal Matrix Composites

Ali Hosseinzadeh, Guney Guven Yapici

Publisher page

Abstract

Abstract In the current work, multi-pass friction stir processing (FSP) was utilized to fabricate samples of fine-grained aluminum–zinc (AZ) magnesium alloy and its metal matrix composite (MMC). The microstructure and high-temperature tensile behavior of friction stir processed (FSPed) AZ31 and AZ31/SiC MMC at various strain rates in the range of 10−2 to 10−4 s−1 were investigated, and the fracture mechanisms of each condition were analyzed. The results verified that MMC samples exhibited a remarkable enhancement in microhardness. The evolution of inclined basal texture was observed after processing for both FSPed and MMC samples. The ambient temperature stress–strain response revealed that the formability of AZ31 has improved after friction stir processing, whereas high-temperature flow curves were discernibly sensitive to strain rate. Equiaxed deep dimples were detected on the fracture surfaces of FSPed samples, but decreased strain rate led to an increase in the number of dimples as attributed to the recrystallization of new grains.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Ozyegin University, Istanbul 34794, Turkey

References (63)

Show source-provided references
1. Strength and Ductility with {10͞11}—{10͞12} Double Twinning in an Magnesium Alloy10.1038/ncomms11068 ↗
2. Effects of Grain Size and Texture on Stress Corrosion Cracking of Friction Stir Processed AZ80 Magnesium Alloy10.1016/j.engfailanal.2018.06.012 ↗
3. Magnesium in Automobiles Application Trends and Advantages
4. Investigation of Microstructure and Mechanical Properties of Friction Stir Welded AZ61 Magnesium Alloy Joint10.1016/j.jma.2018.05.004 ↗
5. Transient Environmental Effects of Light Alloy Substitutions in Transport Vehicles10.1016/j.matdes.2009.01.027 ↗
6. Formation Mechanism of Pit’s on the Surface of Thin-Wall die-Casting Magnesium Alloy Components10.1016/j.engfailanal.2005.01.008 ↗
7. Experimental Studies on Friction Stir Processing of AZ31 Magnesium Alloy10.1016/j.matpr.2017.12.021 ↗
8. Low Temperature Super plasticity of a Fine-Grained ZK60 Magnesium Alloy Processed by Equal-Channel-Angular Extrusion10.1016/S1359-6462(02)00064-7 ↗
9. Equal Channel Angular Extrusion: From Macromechanics to Structure Formation10.1016/S0921-5093(99)00248-8 ↗
10. Novel Ultra-High Straining Process for Bulk Materials Development of the Accumulative Roll-Bonding (ARB) Process10.1016/S1359-6454(98)00365-6 ↗
11. Production of Ultrafine Grain Sizes in Aluminium Sheets by Severe Plastic Deformation Using the Technique of Groove Pressing10.1016/j.scriptamat.2005.03.001 ↗
12. Friction Stir Processing of Large-Area Bulk UFG Aluminum Alloys10.1016/j.scriptamat.2004.09.014 ↗
13. Friction Stir Processing of Commercial AZ31 Magnesium Alloy10.1016/j.jmatprotec.2007.03.045 ↗
14. Production and Characterization of an Advanced AA6061-Graphene-TiB2 Hybrid Surface Nanocomposite by Multi-Pass Friction Stir Processing10.1016/j.surfcoat.2019.124914 ↗
15. On the Surface Reinforcing of A356 Aluminum Alloy by Nanolayered Ti3AlC2 MAX Phase via Friction Stir Processing10.1016/j.surfcoat.2019.08.013 ↗
16. Friction Stir Processing: An Operational Method to Improve Ductility in Pure Copper10.4028/www.scientific.net/AMR.818.14 ↗
17. Microstructures and Tensile Properties of Submerged Friction Stir Processed AZ91 Magnesium Alloy10.1016/j.jma.2015.08.001 ↗
18. Influence of Texture on Superplastic Behavior of Friction Stir Processed ZK60 Magnesium Alloy10.1016/j.msea.2012.07.046 ↗
19. Enhanced Mechanical Properties of Mg–Al–Zn Cast Alloy via Friction Stir Processing10.1016/j.scriptamat.2006.10.035 ↗
20. Microstructural Modification of as-Cast Al-Si-Mg Alloy by Friction Stir Processing10.1007/BF02586167 ↗
21. Singly Dispersed Carbon Nanotube/Aluminum Composites Fabricated by Powder Metallurgy Combined with Friction Stir Processing10.1016/j.carbon.2011.12.034 ↗
22. Ultrafine-Grained Al–Al2Cu Composite Produced in Situ by Friction Stir Processing10.1016/j.scriptamat.2005.04.006 ↗
23. Effect of Friction Stir Processing (FSP) on Microstructure and Properties of Al–TiC in Situ Composite10.1016/j.msea.2011.02.085 ↗
24. High Temperature Characteristics of Al2024/SiC Metal Matrix Composite Fabricated by Friction Stir Processing10.1016/j.msea.2018.06.077 ↗
25. Mg Based Nano-Composites Fabricated by Friction Stir Processing10.1016/j.scriptamat.2005.11.056 ↗
26. Tensile Properties of AZ61 Magnesium Alloy Produced by Multi-Pass Friction Stir Processing: Effect of Sample Orientation10.1016/j.msea.2018.04.017 ↗
27. Submerged Friction Stir Processing of AZ31 Magnesium Alloy10.1016/j.matdes.2012.12.026 ↗
28. Achieving High Strain Rate Superplasticity in Mg–Zn–Y–Zr Alloy Produced by Friction Stir Processing10.1016/j.scriptamat.2011.04.041 ↗
29. Superplastic Behaviour of Friction Stir Processed AZ91 Magnesium Alloy Produced by High Pressure die Cast10.1016/j.jmatprotec.2006.11.005 ↗
30. Effect of Texture on the Mechanical Behavior of Ultrafine Grained Magnesium Alloy10.1016/j.scriptamat.2010.11.052 ↗
31. MWCNTS/AZ31 Surface Composites Fabricated by Friction Stir Processing10.1016/j.msea.2006.01.016 ↗
32. Magnesium Strengthened by SiC Nanoparticles10.1016/S0921-5093(00)01283-1 ↗
33. Mechanical Properties of a Mg–10 (vol%)Ti Composite10.1016/S0266-3538(03)00215-X ↗
34. Superplasticity in a 17 vol% SiC Particulate-Reinforced ZK60A Magnesium Composite (ZK60/SiC/17p)10.1016/0921-5093(95)10060-1 ↗
35. Low Temperature Superplasticity in a Magnesium-Based Composite10.1016/S1359-6462(99)00357-7 ↗
36. Process Parameters Optimization for Friction Stir Welding of RDE-40 Aluminium Alloy Using Taguchi Technique10.1016/S1003-6326(08)60096-5 ↗
37. Friction Stir Welding of Dissimilar Aluminum Alloys AA2219 to AA5083—Optimization of Process Parameters Using Taguchi Technique10.1016/j.matdes.2012.02.016 ↗
38. Particle Effects on Recrystallization in Magnesium–Manganese Alloys: Particle Pinning10.1016/j.msea.2011.02.030 ↗
39. Particle Effects on Recrystallization in Magnesium–Manganese Alloys: Particle-Stimulated Nucleation10.1016/j.actamat.2009.02.032 ↗
40. Current Issues in Recrystallization: a Review10.1016/S0921-5093(97)00424-3 ↗
41. Dynamic Recrystallization Behavior During hot Deformation and Mechanical Properties of 0.2 μm SiCp Reinforced Mg Matrix Composite10.1016/j.msea.2012.10.044 ↗
42. Microstructures and High Temperature Mechanical Properties of Friction Stirred AZ31–Mg Alloy10.1016/j.jallcom.2006.03.066 ↗
43. The Effect of the Inhomogeneous Microstructure and Texture on the Mechanical Properties of AZ31 Mg Alloys Processed by Friction Stir Processing10.1016/j.jallcom.2019.04.014 ↗
44. Increased Room Temperature Formability of Mg AZ31 by High Speed Friction Stir Processing10.1016/j.matdes.2013.08.108 ↗
45. High Strain Rate Superplasticity in a Commercial 2024 Al Alloy via Friction Stir Processing10.1016/S0921-5093(03)00367-8 ↗
46. Microstructure and Mechanical Property of Multi-Walled Carbon Nanotubes Reinforced Aluminum Matrix Composites Fabricated by Friction Stir Processing10.1016/j.matdes.2012.08.036 ↗
47. Novel Nanoparticle-Reinforced Metal Matrix Composites with Enhanced Mechanical Properties10.1002/adem.200700106 ↗
48. Effect of Clustering Induced Porosity on Micromechanical Properties of AA6061/Titanium Oxide Particulate Metal Matrix Composites
49. In Situ Analysis of Damage Evolution in an Al/Al2O3 MMC Under Tensile Load by Synchrotron X-ray Refraction Imaging10.1007/s10853-017-1957-x ↗
50. Mechanical Behavior of Particle Reinforced Metal Matrix Composites10.1002/1527-2648(200106)3:6<357::AID-ADEM357>3.0.CO;2-I ↗
51. An Investigation Into the hot Deformation Characteristics of 7075 Aluminum Alloy10.1016/j.matdes.2010.12.047 ↗
52. Grain Size and Texture Dependence on Mechanical Properties, Asymmetric Behavior and low Temperature Superplasticity of ZK60 Mg Alloy10.1016/j.matchar.2015.06.009 ↗
53. Effect of Reinforcement Size on the Elevated-Temperature Tensile Properties and low-Cycle Fatigue Behavior of Particulate SiC/Al Composites10.1016/S0266-3538(97)00072-9 ↗
54. Mechanical Properties of Friction Stir Processed 2618/Al2O3/20p Metal Matrix Composite10.1016/j.compositesa.2005.03.016 ↗
55. Deformation Behaviors of AZ31 Magnesium Alloy by Equal Channel Angular Extrusion
56. Hot Tensile Deformation Behaviors and Fracture Characteristics of a Typical Ni-Based Superalloy10.1016/j.matdes.2013.10.071 ↗
57. Temperature Dependence of the Rate Sensitivity and Its Effect on the Activation Energy for High-Temperature Flow10.1007/BF02663887 ↗
58. Workability Characteristics and Mechanical Behavior Modeling of Severely Deformed Pure Titanium at High Temperatures10.1016/j.matdes.2013.07.057 ↗
59. Influence of the Grain Size on the Strain Rate Sensitivity in an Mg–Al–Zn Alloy at Moderate Temperatures10.1016/j.scriptamat.2006.07.013 ↗
60. Dynamic Recrystallization in Sintered Cobalt During High-Temperature Deformation10.1007/s11661-010-0181-y ↗
61. A one-Parameter Approach to Determining the Critical Conditions for the Initiation of Dynamic Recrystallization10.1016/1359-6454(95)00146-7 ↗
62. On the Competition Between Particle Fracture and Particle Decohesion in Metal Matrix Composites10.1016/j.actamat.2004.06.009 ↗
63. Investigation of Impact Behaviour of Aluminium Based SiC Particle Reinforced Metal–Matrix Composites10.1016/j.compositesa.2006.02.026 ↗