An Experimental Approach to Continuous Dieless Wire Drawing (Variant A) Using ELI Ti–6Al–4V Alloy
Source abstract
Abstract
This research paper describes a specifically constructed Variant A continuous dieless wire-drawing machine to experimentally determine the principal processing parameters for dieless wire drawing using extra low interstitial Ti–6Al–4V wire alloy. It was experimentally determined that the process was limited by the ratio of the ingoing and outgoing axial velocities, also known as the reduction ratio R and influenced by the primary drawing velocity V1. Reductions of up to 36% per pass wire in cross-sectional area (CSA) were achieved. However, a direct relationship between the wire diameter variation and an increase in overall achievable reduction in CSA was observed. The separation distance between the wire heating and cooling devices (S) was identified as one of the principal governing process parameters. It was found that processing in an inert gas environment led to an increased reduction on CSA of approximately 3% per pass when compared with processing in compressed air. This was attributed to a reduction in surface oxidation and stress cracking. The experimentally determined results showed excellent agreement with a proposed mathematical model. It was also determined that the calculated strain rate for the process fell within the boundaries of previously determined strain rates for this particular alloy. The successful operation of this experimental machine effectively illustrates the possible commercial validity of continuous dieless wire drawing.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metallurgy and Material Forming · Metal Forming Simulation Techniques · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Manufacturing and Operations Engineering, University of Limerick, Limerick, Ireland
Materials and Surface Science Institute (MSSI), University of Limerick, Limerick, Ireland
References (33)
Show source-provided references
1. Dieless Drawing With Transformational Plasticity
2. Dieless Drawing
3. Theory and Application of Dieless Drawing
4. Transformational Plasticity of Titanium
5. The Mechanics of Wire Drawing
6. A Fundamental Study on Dieless Drawing10.1007/978-1-349-01986-1_63 ↗
7. Development of Dieless Drawing Process
8. A Preliminary Investigation of the Dieless Drawing of Titanium and Some Steels
9. Applications of Dieless Drawing to Ti-Ni Wire Drawing and Tapered Steel Wire Manufacturing
10. Calculation of the Temperature Distribution in Dieless Drawing10.1002/srin.199501087 ↗
11. Dieless Drawing: A Forming Process Allowing Flexible Shape Generation10.1007/978-1-349-13796-1_61 ↗
12. A Thermo-Mechanical Analysis of Stability in Dieless Drawing10.1016/S0020-7403(96)00060-4 ↗
13. Tiernan, P. , 1999, “Machine Design, Testing and Analysis of Dieless Wire Drawing,” Ph.D. thesis, University of Limerick, Limerick, Ireland.
14. Dieless Wire Drawing—An Experimental and Numerical Analysis
15. Dieless Laser Drawing of Fine Metal Wires
16. Structural Evolution and Drawability in Laser Dieless Drawing of Fine Nickel Wires
17. LAWD-Laser Assisted Wire Drawing
18. The Use of Titanium for Medical Applications in the USA10.1016/0921-5093(96)10243-4 ↗
19. Titanium in Jet Engines10.1016/B978-0-08-006564-9.50121-4 ↗
20. Pilling
21. Mechanical Behaviour and Superplastic Forming Capabilities of Extra Low Interstitial Grade Ti–6Al–4V Wire Alloy With Numerical Verification
22. The Mechanical Properties of Superplastic Materials10.1007/BF02642383 ↗
23. Mechanisms of Superplastic Flow
24. Mechanical and Microstructural Analysis on the Superplastic Deformation Behavior of Ti–6Al–4V Alloy10.1016/S0020-7403(99)00090-9 ↗
25. Microstructural Evolution of a Ti–6Al–4V Alloy During Thermomechanical Processing10.1016/S0921-5093(01)01531-3 ↗
26. Modelling of Diffusion Bonding of Metals10.1179/mst.1987.3.11.945 ↗
27. An Analysis of Temperature Distributions in Dieless Drawing by Finite Method-Studies of Dieless Drawing 2
28. Analytical Solution for Dieless Drawing Utilising a Method of Equalisation of Work Rates
29. Influence of Oxygen Content on the Forging Response of Equiaxed (Alpha and Beta) Preform of Ti–6Al–4V: Commercial vs. ELI Grade10.1016/S0924-0136(00)00832-3 ↗
30. Smith
31. Effects of Thermal Oxidation on Corrosion and Corrosion Wear Behaviour of a Ti–6Al–4V Alloy10.1016/j.biomaterials.2003.10.009 ↗
32. Improvement of the Oxidation Behaviour of TiAl-Alloys by Treatment With Halogens10.1016/j.intermet.2005.11.032 ↗
33. Der derzeitige Stand der Erkenntnisse uber die mechanischen Vorgang beim Drahtziehen