journal article·2020-10-01

Fracture Behavior of Ultrafine-Grained Titanium Under Tension at Elevated Temperatures

S. V. Sajadifar, H. J. Maier, T. Niendorf, G. G. Yapici

Publisher page

Abstract

Abstract This investigation focused on the deformation response and microstructural changes of severely deformed titanium during post-severe plastic deformation tension, at temperatures of 300–600 °C and at strain rates of 0.001–0.1 s−1. The obtained results suggest that SPD enhances the strength of grade 4 titanium up to 500 °C. At above 600 °C, the severely deformed microstructure showed comprehensive recovery. Severely deformed titanium was seen to be highly sensitive to the deformation rate, where strain rate sensitivity increased with the increase of test temperature. Analysis of fracture surfaces reveals that at elevated temperatures, growth of dimples and void coalescence occurs due to the enhanced diffusion rate and occurrence of recrystallized grains.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Ozyegin University, Istanbul, Turkey;

Universität Kassel, Institut für Werkstofftechnik (Materials Engineering), 34125 Kassel, Germany

Institut für Werkstoffkunde (Materials Science), Leibniz Universität Hannover, 30823 Garbsen, Germany

Department of Mechanical Engineering, Ozyegin University, Istanbul, Turkey

Funding

Marie Curie

References (50)

Show source-provided references
1. Influence of ECAP Routes on the Microstructure and Properties of Pure Ti10.1016/S0921-5093(00)01411-8 ↗
2. Microstructures and Mechanical Deformation Behaviors of Ultrafine-Grained Commercial Pure (Grade 3) Ti Processed by Two-Step Severe Plastic Deformation10.1016/j.msea.2009.07.030 ↗
3. Grain Refinement and Mechanical Properties of CP-Ti Processed by Warm Accumulative Roll Bonding10.1016/j.msea.2012.10.081 ↗
4. Processing of an Ultrafine-Grained Titanium by High-Pressure Torsion: An Evaluation of the Wear Properties With and Without a TiN Coating10.1016/j.jmbbm.2012.08.018 ↗
5. Cellular and Molecular Interactions Between MC3T3-E1 Pre-Osteoblasts and Nanostructured Titanium Produced by High-Pressure Torsion10.1016/j.biomaterials.2007.05.010 ↗
6. Stress-Relieving and Porcelain Firing Cycle Influence on Marginal Fit of Commercially Pure Titanium and Titanium-Aluminum-Vanadium Copings10.1016/S0109-5641(03)00014-9 ↗
7. Texture Evolution in Commercially Pure Titanium After Warm Equal Channel Angular Extrusion10.1016/j.actamat.2010.10.045 ↗
8. Enhanced Ductility in Strongly Textured Magnesium Produced by Equal Channel Angular Processing10.1016/j.scriptamat.2003.10.006 ↗
9. Analysis of Texture Evolution in Magnesium During Equal Channel Angular Extrusion10.1016/j.actamat.2007.09.032 ↗
10. Mechanical Flow Anisotropy in Severely Deformed Pure Titanium10.1016/j.msea.2006.06.082 ↗
11. Product Yield for ECAE Processing10.1016/j.scriptamat.2004.05.022 ↗
12. Thermal Stability and Annealing Behaviour of Ultrafine Grained Commercially Pure Titanium10.1016/j.msea.2011.10.062 ↗
13. Microstructure and Tensile Strength of Grade 2 Titanium Processed by Equal-Channel Angular Pressing and by Rolling10.1007/s10853-012-6593-x ↗
14. Effect of Temperature on Microstructural Stabilization and Mechanical Properties in the Dynamic Testing of Nanocrystalline Pure Ti10.1016/j.msea.2015.03.032 ↗
15. Mechanical Properties and Microstructural Evolution of Nanocrystalline Titanium at Elevated Temperatures10.1016/j.msea.2016.05.105 ↗
16. Elevated Temperature Mechanical Behavior of Severely Deformed Titanium10.1007/s11665-014-0947-2 ↗
17. Workability Characteristics and Mechanical Behavior Modeling of Severely Deformed Pure Titanium at High Temperatures10.1016/j.matdes.2013.07.057 ↗
18. The Microstructural Evolution and Thermo-Mechanical Behavior of UFG Ti Processed via Equal Channel Angular Pressing10.1016/j.jmatprotec.2014.12.024 ↗
19. Sajjadifar · 2017
20. High Temperature Flow Response Modeling of Ultra-Fine Grained Titanium10.3390/met5031315 ↗
21. Effect of Severe Plastic Deformation on the Damping Behavior of Titanium10.1016/j.matlet.2019.02.010 ↗
22. Cyclic Deformation Response of Ultra-Fine Grained Titanium at Elevated Temperatures10.1016/j.ijfatigue.2019.01.021 ↗
23. Materials Processing by Simple Shear10.1016/0921-5093(95)09705-8 ↗
24. Engineering and Commercialization of Equal Channel Angular Extrusion (ECAE)10.1016/S0921-5093(04)00934-7 ↗
25. The Effect of Strain Rate on the Deformation Mechanisms and the Strain Rate Sensitivity of an Ultra-Fine-Grained Al Alloy10.1016/j.scriptamat.2009.03.032 ↗
26. Dynamic Recovery and Recrystallization in Titanium Alloys by Hot Deformation10.1007/s11837-007-0013-8 ↗
27. Flow Stress Behavior of Commercial Pure Titanium Sheet During Warm Tensile Deformation10.1016/j.matdes.2011.07.060 ↗
28. On the Mechanical Behavior of Cold Deformed Aluminum 7075 Alloy at Elevated Temperatures10.1016/j.msea.2016.05.113 ↗
29. High Temperature Deformation Behavior of 4340 Steel: Activation Energy Calculation and Modeling of Flow Response10.1016/S1006-706X(13)60226-5 ↗
30. Mechanical Behavior of Ultrafine-Grained Titanium Rods Obtained Using Severe Plastic Deformation10.1134/S0031918X08080140 ↗
31. Work-Hardening Effect and Strain-Rate Sensitivity Behavior During Hot Deformation of Ti–5Al–5Mo–5V–1Cr–1Fe Alloy10.1016/j.matdes.2015.05.060 ↗
32. Mechanical Behavior and Superplasticity of a Severe Plastic Deformation Processed Nanocrystalline Ti–6Al–4V Alloy10.1016/S0921-5093(00)01338-1 ↗
33. Hot Deformation Behavior of P/M Al6061-20% SiC Composite10.4028/www.scientific.net/MSF.534-536.897 ↗
34. Effect of Oxygen Content on Grain Growth Kinetics of Titanium10.1023/A:1023094126132 ↗
35. Effect of Purity Levels on the High-Temperature Deformation Characteristics of Severely Deformed Titanium10.1007/s11661-016-3929-1 ↗
36. Monitoring the Fatigue-Induced Damage Evolution in Ultrafine-Grained Interstitial-Free Steel Utilizing Digital Image Correlation10.1016/j.msea.2009.04.053 ↗
37. Cyclic Stability of Ultrafine-Grained Interstitial-Free Steel at Elevated Temperatures10.1016/j.msea.2008.03.054 ↗
38. Hot Tensile Deformation Behaviors and Constitutive Model of an Al–Zn–Mg–Cu Alloy10.1016/j.matdes.2014.02.052 ↗
39. Modeling the Hot Ductility of AA6061 Aluminum Alloy After Severe Plastic Deformation10.1007/s11837-015-1354-3 ↗
40. Grain Boundary Sliding and Accommodation Mechanisms During Superplastic Deformation of ZK40 Alloy Processed by ECAP10.1007/s10853-005-2163-9 ↗
41. Hot Embrittlement and Effect of Grain Size on Hot Ductility of Martensitic Heat-Resistant Steels10.1016/j.msea.2016.09.072 ↗
42. A One-Parameter Approach to Determining the Critical Conditions for the Initiation of Dynamic Recrystallization10.1016/1359-6454(95)00146-7 ↗
43. Dynamic Recrystallization in Sintered Cobalt During High-Temperature Deformation10.1007/s11661-010-0181-y ↗
44. Compressive Deformation Behaviors of Coarse- and Ultrafine-Grained Pure Titanium at Different Temperatures: A Comparative Study10.2320/matertrans.M2011041 ↗
45. Hot Tensile Deformation and Fracture Behaviors of AZ31 Magnesium Alloy10.1016/j.matdes.2013.01.023 ↗
46. Mechanical Properties of Ultra-Fine Grain Titanium
47. Smallman · 1995
48. Effect of Equal Channel Angular Pressing on the Fracture Behavior of Commercially Pure Titanium10.1007/s11661-009-0111-z ↗
49. Numerical Studies of Porous Ductile Materials Containing Arbitrary Ellipsoidal Voids—II: Evolution of the Length and Orientation of the Void Axes10.1016/j.euromechsol.2013.06.005 ↗
50. Coalescence of Voids by Internal Necking: Theoretical Estimates and Numerical Results10.1016/j.jmps.2014.11.009 ↗