Determination of the Shear Modulus of Orthotropic Thin Sheets With the Anticlastic-Plate-Bending Experiment
Source abstract
Abstract
The shear modulus of orthotropic thin sheets from three advanced high-strength steels (AHSS) is measured using the anticlastic-plate-bending (APB) experiment. In APB, a thin square plate is loaded by point forces at its four corners, paired in opposite directions. It thus assumes the shape of a hyperbolic paraboloid, at least initially. The principal stress directions coincide with the plate diagonals, and the principal stresses are equal and opposite. Hence, at 45 deg to these, a state of pure shear exists. A finite element (FE) study of APB is reported first, using both elastic and elastoplastic material models. This study confirms the theoretical predictions of the stress field that develops in APB. The numerical model is then treated as a virtual experiment. The input shear modulus is recovered through this procedure, thus validating this approach. A major conclusion from this numerical study is that the shear modulus for these three AHSS should be determined before the shear strain exceeds 2 × 10−4 (or 200 με). Subsequently, APB experiments are performed on the three AHSS (DP 980, DP 1180 and MS 1700). The responses recorded in these experiments confirm that over 3 × 10−4 strain (or 300 με) the response differs from the theoretically expected one, due to excessive deflections, yielding, changing contact conditions with the loading rollers and, in general, the breaking of symmetry. But under that limit, the responses recorded are linear, and can be used to determine the shear modulus.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Structural Load-Bearing Analysis · Metal Forming Simulation Techniques · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Center for Advanced Materials and Manufacturing Innovation (CAMMI), University of New Hampshire, 33 Academic Way, Durham, NH 03824
Department of Mechanical Engineering, Center for Advanced Materials and Manufacturing Innovation (CAMMI), University of New Hampshire, 33 Academic Way, Durham, NH 03824 e-mail:
References (29)
Show source-provided references
1. Elastic Anisotropy of Dual-Phase Steels With Varying Martensite Content10.1016/j.ijsolstr.2018.02.028 ↗
2. Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Impulse Excitation of Vibration
3. Dynamic Elastic Modulus Measurements in Materials
4. The Determination of Poisson's Ratio and the Dynamic Modulus of Elasticity From the Frequencies of Natural Vibration in Thick Circular Plates10.1016/0022-460X(65)90089-1 ↗
5. A Comparison of Experimental and Theoretical Relations Between Young's Modulus and the Flexural and Longitudinal Resonance Frequencies of Uniform Bars10.6028/jres.064A.014 ↗
6. New Accurate Procedure for Single Shear Testing of Metals
7. The Iosipescu Shear Test as Applied to Composite Materials10.1007/BF02323208 ↗
8. The Losipescu Shear Test as Applied to Composite Materials10.1007/BF02328688 ↗
9. Standard Test Methods for Shear Properties of Composite Materials by the V-Notched Beam Method
10. An Evaluation of the Arcan Specimen for Determining the Shear Moduli of Fiber-Reinforced Composites10.1007/BF02317314 ↗
11. A Method to Produce Uniform Plane-Stress States With Applications to Fiber-Reinforced Materials10.1007/BF02324146 ↗
12. A New Method for the Biaxial Testing of Cellular Solids10.1007/BF02410498 ↗
13. Design and Validation of a New Fixture for the Shear Testing of Cellular Solids10.1007/s00419-013-0801-2 ↗
14. Study on Intra/Inter-Ply Shear Deformation of Three Dimensional Woven Preforms for Composite Materials10.1016/j.matdes.2013.02.025 ↗
15. Two-Dimensional Macro-Mechanics Shear Models of Woven Fabrics10.1016/S1359-835X(04)00185-X ↗
16. Characterisation of the Shear–Tension Coupling of Carbon-Fibre Fabric Under Controlled Membrane Tensions for Precise Simulative Predictions of Industrial Preforming Processes10.1016/j.compositesa.2014.08.030 ↗
17. Identifying the Distinct Shear Wrinkling Behavior of Woven Composite Preforms Under Bias Extension and Picture Frame Tests10.1016/j.compstruct.2017.11.033 ↗
18. In-Plane Shear Test of Thin Panels10.1007/BF02328685 ↗
19. Intra/Inter-Ply Shear Behaviors of Continuous Fiber Reinforced Thermoplastic Composites in Thermoforming Processes10.1016/j.compstruct.2011.01.002 ↗
20. Design of Fiber Metal Laminate Shear Panels for Ultra-High Capacity Aircraft10.1016/S1369-8869(01)00003-9 ↗
21. On Anticlastic Curvature With Special Reference to Plastic Bending: A Literature Survey and Some Experimental Investigations10.1016/0020-7403(67)90011-2 ↗
22. 1959
23. Experimental Investigation of Subsequent Yield Surfaces Using the Moiré Method10.1016/0022-5096(65)90032-3 ↗
24. Investigation of Mode III Fracture Toughness Using an Anti-Clastic Plate Bending Method10.1016/S0013-7944(98)00020-4 ↗
25. STP-1191: A Simple Test Method and Apparatus for Biaxial Fatigue and Crack Growth Studies10.1520/STP1191-EB ↗
26. Standard Test Methods for Shear Modulus of Wood-Based Structural Panels
27. Fibre-Reinforced Plastic Composites—Determination of the In-Plane Shear Modulus by the Plate Twist Method
28. Determination of Shear Modulus and Poisson's Ratio of Polymers and Foams by the Anticlastic Plate-Bending Method10.1007/BF02480690 ↗
29. Buckling Phenomena in Double Curved Cold-Bent Glass10.1016/j.ijnonlinmec.2014.03.015 ↗