Tailoring Microstructure and Performance of CMT-WAAM Deposited Al 4047 Alloy Wall Through Interlayer Addition of Rare Earth La2O3 Nanoparticles
Source abstract
Abstract
Abstract The present work investigates the effect of rare earth Lanthanum oxide (La2O3) nanoparticles on the microstructure, mechanical properties, and residual stress of Al 4047 alloy wall fabricated via cold metal transfer-based wire and arc additive manufacturing (CMT-WAAM). Results from microstructural analyses reveal that without La2O3 nanoparticles, the structure consists of coarse columnar crystals and dendrites, while the addition of La2O3 nanoparticles leads to significant refinement, promoting fine equiaxed dendrites and a reduction in pores. Energy dispersive spectroscopy (EDS) mapping confirms the uniform distribution of La2O3 nanoparticles, which aids in enhancing nucleation during solidification. Mechanical results show that walls with nano-La2O3 exhibit a uniform and increased microhardness and tensile strength, with improvements being more pronounced in the deposition direction than in the build direction. Although the presence of nanoparticles led to reduced ductility, as evidenced by lower elongation and finer, more uniformly distributed dimples were observed in the fractographic analysis. Adding La2O3 nanoparticles decreased residual stress in the wall, with higher compressive stress in the bottom layers from repeated heating, while the top layers experienced tensile stress from rapid cooling.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Delhi Technological University Department of Mechanical Engineering, , ,
References (36)
Show source-provided references
1. A Review on Wire Arc Additive Manufacturing: Processing Parameters, Defects, Quality Improvement and Recent Advances10.1016/j.mtcomm.2022.103739 ↗
2. Impact of Depositional Direction and Current on Microstructure and Mechanical Properties of the Bimetallic Wall of ER5356/ER4043 Fabricated by Cold Metal Transfer Based Wire Arc Additive Manufacturing10.1016/j.cirpj.2024.06.013 ↗
3. Effect of Travel Speed on the Properties of 5087 Aluminum Alloy Walls Produced by Wire and Arc Additive Manufacturing10.1007/s11665-024-09166-3 ↗
4. Cold Metal Transfer (CMT) Technology—An Overview10.1016/j.dt.2017.08.002 ↗
5. Additive Manufacturing of Metals10.1016/j.actamat.2016.07.019 ↗
6. Wear Performance Enhancement of Interface Layer in Cold Metal Transfer-Based WAAM-Fabricated ER4043/ER5356 Bimetallic Wall Through Friction Stir Surface Treatment10.1115/1.4067281 ↗
7. Effects of Rare Earths on Microstructure and Wear Resistance in Metal Additive Manufacturing A Review10.3390/coatings14010139 ↗
8. A Review of Recent Research on Rare Earth Particulate Composite Materials and Structures with Their Applications10.1007/s12666-021-02338-y ↗
9. A Review on Recent Applications and Future Prospects of Rare Earth Oxides in Corrosion and Thermal Barrier Coatings, Catalysts, Tribological, and Environmental Sectors10.1016/j.ceramint.2022.07.220 ↗
10. Tailoring the Microstructure and Properties of AA6061-T6/TiB2 Cast Composites With the Addition of Rare Earth La2O3 Nanoparticles10.1016/j.coco.2024.102230 ↗
11. Grain Refinement of Additive Manufactured Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Titanium Alloy by the Addition of La2O310.1016/j.matlet.2020.128170 ↗
12. Effect of Titanium Powder on Microstructure and Mechanical Properties of Wire + Arc Additively Manufactured Al-Mg Alloy10.1016/j.matlet.2019.01.117 ↗
13. Realization of Structural Evolution in Grain Boundary, Solute Redistribution and Improved Mechanical Properties by Adding TiCnps in Wire and Arc Additive Manufacturing 2219 Aluminium Alloy10.1016/j.jmrt.2021.01.030 ↗
14. Effect of La2O3 Particle Size on the Microstructure and Properties of AlSi Alloys Deposited via Wire Arc Additive Manufacturing10.1016/j.jmapro.2021.05.069 ↗
15. Effect of Interlayer Coating La2O3 Particles on Arc Behavior and Microstructure of Wire Arc Additive Manufacturing Al-Si Alloy Deposition10.1016/j.jmapro.2023.06.032 ↗
16. Microstructural, Mechanical and Energy Demand Characterization of Alternative WAAM Techniques for Al-Alloy Parts Production10.1016/j.cirpj.2020.08.001 ↗
17. Effect of Rare Earth La2O3 on the Microstructure and Tribological Properties of Laser-Clad CoCrFeNiMoSi High-Entropy Alloy Coatings10.1016/j.matlet.2023.135398 ↗
18. Preparation and Characterization of High-Efficiency Deposition WAAM AlSi Alloy Assisted Through Magnetic Field Regulation and Interlayer Spraying Lanthanum Oxide Powder10.1016/j.jmapro.2024.06.073 ↗
19. Evaluation of the Role of Process Parameters of CMT Welding and Their Statistical Behaviour on the Tensile Properties of Weld Joint of Novel Aluminium Hybrid Composite10.1007/s40194-024-01805-6 ↗
20. Porosity in Wire Arc Additive Manufacturing of Aluminium Alloys10.1016/j.addma.2021.101993 ↗
21. Pore Formation and Evolution in Wire + Arc Additively Manufactured 2319 Al Alloy10.1016/j.addma.2019.100900 ↗
22. Effect of Lanthanum Oxide on the Microstructure and Properties of Ti-6Al-4V Alloy During CMT-Additive Manufacturing10.3390/cryst13030515 ↗
23. Improvement of Microstructure and Mechanical Properties of CMT Wire Arc Additive Manufacturing Al-Si Alloy Deposition via Interlayer Coating TiC Nanoparticles10.1016/j.mtcomm.2023.107851 ↗
24. Wire Arc Additive Manufacturing of Nanomodified 2024 Alloy10.1016/j.matlet.2023.134712 ↗
25. Microstructure Evolution and Mechanical Properties of Cold Metal Transfer Additive Manufactured Ti–6Al–4V Wall With Trace MoSi2 Addition10.1016/j.msea.2020.140160 ↗
26. Evaluation of Microstructure, Residual Stress, and Mechanical Properties in Different Planes of Wire + Arc Additive Manufactured Nickel-Based Superalloy10.1007/s12540-022-01185-w ↗
27. Review on Residual Stresses in Metal Additive Manufacturing: Formation Mechanisms, Parameter Dependencies, Prediction and Control Approaches10.1016/j.jmrt.2022.02.054 ↗
28. Residual Stress in Wire and Arc Additively Manufactured Aluminum Components10.1016/j.jmapro.2021.02.021 ↗
29. Influence of the WAAM Process and Design Aspects on Residual Stresses in High-Strength Structural Steels10.1007/s40194-023-01503-9 ↗
30. Fatigue Crack Propagation Behaviour in Wire + Arc Additive Manufactured Ti-6Al-4V: Effects of Microstructure and Residual Stress10.1016/j.matdes.2015.10.141 ↗
31. Investigation of Residual Stress Distribution of Dissimilar Al-7075-T6 and Al-6061-T6 in the Friction Stir Welding Process Strengthened With SiO2 Nanoparticles10.1016/j.jmapro.2019.05.023 ↗
32. Influence of La2O3 Addition on Nano Indentation Hardness and Residual Stress of Stellite 6 Coating Prepared by Plasma Cladding10.1016/j.jre.2018.03.008 ↗
33. Influence of Nano-Sized WC Addition on the Microstructure, Residual Stress, and Tribological Properties of WC-Co HVAF-Sprayed Coatings10.1016/j.surfcoat.2024.130696 ↗
34. The Effect of Microstructure Parameters on the Residual Stresses in the Ultrafine-Grained Sheets10.1016/j.micron.2020.102843 ↗
35. Grain Size Influence on Residual Stresses in Alumina/Zirconia Composites10.1016/S1359-6454(97)00348-0 ↗
36. Effect of Grain Size on Thermal Residual Stresses and Damage in Sintered Chromium–Alumina Composites: Measurement and Modeling10.1016/j.compositesb.2014.06.027 ↗