The Mechanical Behavior of Zinc During Machining
Source abstract
Abstract
It is well known that a nonzero force is obtained when cutting forces measured at different feed rates but otherwise constant cutting conditions are extrapolated to zero feed rate. In the literature, this nonzero intercept has been attributed to a ploughing effect associated with the finite sharpness of the cutting tool. However, the standard extrapolation method does not account for other variables such as strain, strain rate and temperature which also vary with feed rate and influence the work material flow stress. In this paper, the apparent flow stresses measured in high and low speed machining tests on zinc are compared with the flow stresses measured in compression tests. The results show that the flow stress measured in cutting is consistent with that measured in compression when all deformation variables are properly accounted for and that, contrary to the results obtained using the extrapolation approach, the ploughing force is negligible.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
General Motors Research and Development Center, 30500 Mound Road, Warren, MI 49090-9055
References (40)
Show source-provided references
1. Abdelmoneim M. Es. , 1976, “Comments on ‘Friction in Metal Machining—Mechancial Aspects,’” Wear, Vol. 38, pp. 391–394.10.1016/0043-1648(76)90085-5 ↗
2. Abdelmoneim M. Es. , and ScruttonR. F., 1974, “Tool Edge Roundness and Stable Build-up Formation in Finish Machining,” ASME Journal of Engineering for Industry, Vol. 96, pp. 1258–1267.10.1115/1.3438504 ↗
3. Albrecht P. , 1960, “New Developments in the Theory of the Metal-Cutting Process. Part I. The Ploughing Process in Metal Cutting,” ASME Journal of Engineering for Industry, Vol. 82, pp. 348–357.10.1115/1.3664242 ↗
4. Altintas Y. , MontgomeryD., and BudakE., 1992, “Dynamic Peripheral Milling of Flexible Structures,” ASME Journal of Engineering for Industry, Vol. 114, pp. 137–145.10.1115/1.2899766 ↗
5. Altintas Y. , and YellowleyI., 1989, “In-Process Detection of Tool Failure in Milling Using Cutting Force Models,” ASME Journal of Engineering for Industry, Vol. 111, pp. 149–157.10.1115/1.3188744 ↗
6. Bailey J. A. , 1975, “Friction in Metal Machining—Mechanical Aspects,” Wear, Vol. 31, pp. 243–275.10.1016/0043-1648(75)90161-1 ↗
7. Black J. T. , 1979, “Flow Stress Model in Metal Cutting,” ASME Journal of Engineering for Industry, Vol. 101, pp. 403–415.10.1115/1.3439527 ↗
8. Clack V. W. , and BrewerR. C., 1966–67, “New Technique for Shear Zone Thickness Determination in Orthogonal Metal Cutting,” Proceedings of the Institution of Mechanical Engineers, Vol. 181, Part 1, No. 25, pp. 667–686.10.1243/PIME_PROC_1966_181_059_02 ↗
9. Elbestawi M. A. , PapazafirouT. A., and DuR. X., 1991, “In-Process Monitoring of Tool Wear in Milling Using Cutting Force Signature,” Int. J. Mach. Tools Manufact., Vol. 31, pp. 55–73.10.1016/0890-6955(91)90051-4 ↗
10. Holzer A. J. , and WrightP. K., 1981, “Dynamic Plasticity: A Comparison Between Results from Mechanical Testing and Machining,” Materials Science and Engineering, Vol. 51, pp. 81–92.10.1016/0025-5416(81)90109-9 ↗
11. Hongtao Z. , PeideL., and RongshengH., 1989, “The Theoretical Calculation of Naturally Curling Radius of Chip,” Int. J. Mach. Tools Manufact., Vol. 29, No. 3, pp. 295–303.10.1016/0890-6955(89)90003-5 ↗
12. Hsu T. C. , 1966, “A Study of the Normal and Shear Stresses on a Cutting Tool,” ASME Journal of Engineering for Industry, Vol. 88, pp. 51–64.10.1115/1.3670890 ↗
13. Kececioglu D. , 1958, “Shear Strain-Rate in Metal Cutting and its Effects on Shear-Flow Stress,” Trans. ASME, Vol. 80, pp. 158–168.10.1115/1.4012293 ↗
14. Kobayashi S. , and ThomsenE. G., 1959, “Some Observations on the Shearing Process in Metal Cutting,” ASME Journal of Engineering for Industry, Vol. 81, pp. 251–262.10.1115/1.4008316 ↗
15. Kocks, U. F., Stout, M. G., and Rollet, A. D., 1988, “The Influence of Texture on Strain Hardening,” Strength of Metals and Alloys (ICSMA 8), Proceedings of the 8th International Conference, Tampere, Finland, 22–26 Aug. 1988, P. O. Kettunen, T. K. Lepisto, and M. E. Lehtonen, eds., Pergamon Press, pp. 25–34.
16. Loewen E. G. , and ShawM. C., 1954, “On the Analysis of Cutting Tool Temperatures,” Trans. ASME, Vol. 76, pp. 217–236.10.1115/1.4014799 ↗
17. Lovato M. L. , and StoutM. G., 1992, “Compression Testing Techniques to Determine the Stress/Strain Behavior of Metals Subject to Finite Deformation,” Metallurgical Transactions A, Vol. 23A, pp. 935–951.10.1007/BF02675569 ↗
18. Merchant M. E. , 1945a, “Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and the Type 2 Chip,” Journal of Applied Physics, Vol. 16, pp. 267–275.10.1063/1.1707586 ↗
19. Merchant M. E. , 1945b, “Mechanics of the Metal Cutting Process. II. Plasticity Conditions in Metal Cutting,” Journal of Applied Physics, Vol. 16, pp. 318–324.10.1063/1.1707596 ↗
20. Oxley, P. L. B., 1989, The Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Horwood Limited, Chichester.
21. Palmer W. B. , and OxleyP. L. B., 1959, “Mechanics of Orthogonal Cutting,” Proceedings of Institution of Mechanical Engineers, Vol. 173, pp. 623–638.10.1243/PIME_PROC_1959_173_053_02 ↗
22. Partridge P. G. , 1867, “Crystallography and Deformation Modes of H. C. P. Metals,” Metallurgical Reviews, Vol. 12, pp. 169–194.10.1179/mtlr.1967.12.1.169 ↗
23. Santhanam S. , and ShawM. C., 1985, “Flow Characteristics for the Complex Stress State in Metal Cutting,” Annals of the CIRP, Vol. 34/1, pp. 109–111.10.1016/S0007-8506(07)61735-1 ↗
24. Shaw M. C. , and FinnieI., 1955, “The Shear Stress in Metal Cutting,” Trans. ASME, Vol. 1955, pp. 115–125.10.1115/1.4014257 ↗
25. Shaw M. C. , and SuhN. P., 1960, Discussion and Closure on “New Developments in the Theory of Metal-Cutting Process,” by P. Albrecht, ASME Journal of Engineering for Industry, Vol. 82, pp. 357–358.10.1115/1.3664244 ↗
26. Stephenson D. A. , 1993, “Tool-Work Thermocouple Temperature Measurements: Theory and Implementation Issues,” ASME Journal of Engineering for Industry, Vol. 115, pp. 432–437.10.1115/1.2901786 ↗
27. Stephenson D. A. , 1991, “Assessment of Steady-State Metal Cutting Temperature Models Based on Simultaneous Infrared and Thermocouple Measurements,” ASME Journal of Engineering for Industry, Vol. 113, pp. 121–128.10.1115/1.2899668 ↗
28. Stephenson D. A. , 1989, “Material Characterization for Metal-Cutting Force Modelling,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 111, pp. 210–219.10.1115/1.3226461 ↗
29. Stevenson R. , 1992, “The Morphology of Machining Chips Formed During Low Speed Quasi-Orthogonal Machining of CA 360 Brass and a Mechanism for their Formation,” ASME Journal of Engineering for Industry, Vol. 114, pp. 404–411.10.1115/1.2900691 ↗
30. Stevenson, R., 1990, “Force Variations During Low Speed Quasi-Orthogonal Machining of CA 360 Brass,” ASME PED-Vol. 43, Fundamental Issues in Machining, B. E. Klamecki and K. J. Weinman, eds., ASME WAM 1990, pp. 39–55.
31. Stevenson, R., 1982, “Inferring Microscopic Deformation Behavior From the Form of Constitutive Equations for Low-Carbon Steel and 5182-0 Aluminum,” Mechanical Testing for Deformation Model Development, ASTM STP-765, R. W. Rohde and J. C. Swearengen, eds., pp. 366–381.10.1520/STP28897S ↗
32. Sutherland J. W. , and DevorR. E., 1986, “An Improved Method for Cutting Force and Surface Error Prediction in Flexible End Milling Systems,” ASME Journal of Engineering for Industry, Vol. 108, pp. 269–279.10.1115/1.3187077 ↗
33. Takeyama H. , and UsuiE., 1958, “The Effect of Tool-Chip Contact Area in Metal Machining,” Trans. ASME, Vol. 80, pp. 1089–1096.10.1115/1.4012614 ↗
34. Voce E. , 1948, “The Relationship Between Stress and Strain for Homogeneous Deformation,” Journal of the Institute of Metals, Vol. 74, pp. 760–761.
35. Von Turkovich B. F. , and FieldM., 1981, “Survey on Material Behavior in Machining,” Annals of the CIRP, Vol. 30/2, pp. 533–540.10.1016/S0007-8506(07)60163-2 ↗
36. Wagoner R. H. , 1981, “A Technique for Measuring Strain-Rate Sensitivity,” Metallurgical Transactions A, Vol. 12A, pp. 71–75.10.1007/BF02648510 ↗
37. Wallace P. W. , and BoothroydG., 1964, “Tool Forces and Tool-Chip Friction in Orthogonal Machining,” Journal of Mechanical Engineering Science, Vol. 6, pp. 74–87.10.1243/JMES_JOUR_1964_006_013_02 ↗
38. Williams J. A. , and GaneN., 1977, “Some Observations on the Flow Stress of Metals During Metal Cutting,” Wear, Vol. 42, pp. 341–353.10.1016/0043-1648(77)90062-X ↗
39. Zorev N. N. , 1959, “Communication on ‘Mechanics of Orthogonal Machining,’” Proceedings of Institution of Mechanical Engineers, Vol. 173, pp. 645–651.
40. Zorev, N. N., 1966, Metal Cutting Mechanics, Pergamon Press, Oxford, pp. 129–180.