Numerical Simulation of a Heat-Treated Ring Gear Blank
Source abstract
Abstract
Carburization and quenching of steels in general has been and continues to be an important commercial manufacturing process for steel components. The minimization of distortion, cracking, and residual stresses are major issues that need to be properly understood in order to efficiently produce high quality components. To assist process engineers in understanding the effect process parameters have on these major issues, a numerical study was conducted on an automotive transmission ring gear. The ring gear has substantial ovaling distortion, which cannot always be straightened within the design tolerances of the part thereby leading to a 3–5 percent rejection rate. The purpose of this report is to predict the distortions, microstructural phase changes, residual stresses, and hardness that occur during quenching using finite element techniques. The ABAQUS model from the NCMS Heat Treatment Prediction Program was used to perform the simulations. This report describes a two-dimensional simulation of the gear blank with the wall thinned where the teeth would have been located to represent the proper thermal mass. The gear blank geometry is essentially the same as the gear geometry without the teeth; moreover it has the same dimensions exhibited by the gear. Even though the ovaling caused by distortion is a three-dimensional problem the two-dimensional representation was chosen as an initial step before simulating the more complex three-dimensional gear geometry. The symmetry of the blank can be exploited by allowing fewer elements to be used for the finite element analysis which in turn will decrease the simulation times of the problem. [S0094-4289(00)01103-8]
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Scientific Research Laboratory, Ford Motor Company, Dearborn, MI 48121
MLC Technical Consultant, Livermore, CA 94550
References (15)
Show source-provided references
1. Mgbokwere, C., Dowling, W., Smith, D., Copple, W., and Mack C., 1999, “2D-Simulation of a 211 Ring gear Blank,” The Third International Conference on Quenching and Control Distortion, ASM, pp. 234–253.
2. Ishigawa, H. J. , 1978, “Phase Transformation in Steels,” J. Thermal Stress., 1, pp. 211–222.
3. Burmett, J. A., and Padovan, J., 1979, “Residual Stress Fields in Heat-Treated Case-Hardened Cylinders,” J. Thermal Stress., 2, pp. 251–263.10.1080/01495737908962404 ↗
4. Rammerstorfer, F. G., Fischer, W., Mitter, K., Bathe, J., and Snyder, M. D., 1981, “On Thermo-Elastic-Plastic Analysis of Heat-Treatment Processes Including Creep and Phase Changes,” Comput. Struct., 13, pp. 771–779.10.1016/0045-7949(81)90040-7 ↗
5. Leblond, J. B., Devaux, J., and Devaux, J. C., 1989, “Mathematical Modeling of Transformation Plasticity in Steels I: case of Ideal-Plastic Phases,” Int. J. Plast., 5, pp. 573–591.10.1016/0749-6419(89)90001-6 ↗
6. VonBergen, R. T., 1992, “The Effects of Quenchant Media Selection and Control on the Distortion of Engineered Steel Parts,” First International Conference on Quenching and Distortion Control, G. E. Totten, ed., pp. 275–282.
7. Roberts, C. S. , 1953, “Effects of Carbon on the Volume Fractions and Lattice Parameters of Retained Austenite and Martensite,” Trans. AIME, 197, p. 203203.
8. Kirkaldy, J. S., and Venugopalan, D., 1984, “Phase Transformation in Ferrous Alloys,” AIME Publications, Marder, A. R., and Goldenstein, J. I., eds., p. 125.
9. Watt, D. F., Coon, L., Bibby, M., Goldak, J., and Henwood, C., 1988, “An Algorithm for Modelling Microstructural Development in Weld Heat-Affected Zones. Part A. Reaction Kinetics,” Acta Metall., 36, pp. 3029–3035.10.1016/0001-6160(88)90185-X ↗
10. Asby, M. F., and Easterling, K. E., 1982, “First Report on Diagrams for Grain Growth in Welds,” Acta Metall., 30, pp. 1969–1978.10.1016/0001-6160(82)90100-6 ↗
11. Lusk, M., Krauss, G., and Jou, H., 1995, “A New Balance Principle for Modeling Phase Transformation Kinetics,” International Conference on Martensite Transformations, pp. 123–131.
12. Bammann, D. J., Prantil, V. C., and Lathrop, J. F., 1995, “A Model of Phase Transformation Plasticity,” Modelling of Casting, Welding and Advanced Solidification Processes VII, Cross, M., and Campbell, J., eds., pp. 275–285.
13. Fischer, F. D., Sun, Q-P., and Tanaka, K., 1996, “Transformation-Induced Plasticity (TRIP),” Appl. Mech. Rev., 49, pp. 317–364.10.1115/1.3101930 ↗
14. Krauss, G., 1992, “Heat Treatment, Microstructures, and Residual Stresses in Carburized Steels,” First International Conference on Quenching and Distortion Control, G. E. Totten, ed., pp. 181–191.
15. Das, S., Upadhya, G., and Chandra, U., 1992, “Prediction of Macro- and Micro-Residual Stress in Quenching using Phase Transformation Kinetics,” First International Conference on Quenching and Distortion Control, G. E. Totten, ed., pp. 229–234.