journal article·2006-07-01

Measurement and Prediction of the Residual Stress Field Generated by Side-Punching

A. H. Mahmoudi, D. Stefanescu, S. Hossain, C. E. Truman, D. J. Smith, P. J. Withers

Publisher page

Abstract

Side-punching is proposed as a method of introducing a well-defined residual stress field into a laboratory-sized test specimen. Such a specimen may subsequently be used to assess the influence of residual stresses on the fracture behavior of materials. Side-punching consists of simultaneously indenting opposite faces of a plate of material with rigid tools, using sufficient force to cause localized yielding over a finite-sized volume of material adjacent to the punching tools. This paper presents experimental measurements, obtained using three independent measurement techniques, of the residual stress field generated in an aluminium alloy plate after side-punching. Incremental center hole drilling is used to determine the near-surface residual stress field, while synchrotron x-ray diffraction and deep hole drilling are used to measure the through-thickness residual stress field along a path linking the two punch center points. Finite element (FE) predictions are also presented and compared to the measurements. There is very good agreement between all three sets of measurements and the FE results, which all show that the through-thickness residual stresses are compressive and attain a maximum value at the center of the plate. The results confirm the potential use of side-punching in residual stress-crack interaction studies.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Fatigue and fracture mechanics · Welding Techniques and Residual Stresses · Non-Destructive Testing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, University of Bristol, Queen’s Building, University Walk, Bristol, BS8 1TR, UK

Manchester Material Science Centre, University of Manchester, Grosvenor St., Manchester, M1 7HS, UK

References (21)

Show source-provided references
1. The Influence of Prior Loading on Structural Integrity10.1016/B0-08-043749-4/07116-0 ↗
2. Residual Stresses, Part 1—Measurement Techniques10.1179/026708301101509980 ↗
3. Mahmoudi, A. H., Hadidi-Moud, S., Truman, C. E., and Smith, D. J., 2003, “Measurement and Prediction of Residual Stress Generated by Local Compression,” 5th European Solid Mechanics Conference, ESMC-5, Thessaloniki, Greece.
4. The Effect of Residual Macrostresses and Microstressses on Fatigue Crack Propagation10.1007/s11661-998-0038-9 ↗
5. Residual Stress Driven Creep Cracking in Type 316 Stainless Steel
6. Ogeman, R. , 1993, “Coining Residual Stresses in Aluminium Ship Structures: Experiments and FE Simulations,” Dissertation, School of Mechanical and Vehicular Engineering, Department of Marine Structural, Sweden.
7. Analytical and Experimental Study of Fracture in Bend Specimens Subjected to Local Compression10.1520/STP11087S ↗
8. Lacarac, V. , 2000, “Residual Stresses and Fatigue Crack Growth From Cold Expanded Holes in Al2650 at Room and High Temperature,” Ph.D. thesis, University of Bristol.10.1016/S0142-1123(99)00126-7 ↗
9. Garcia-Granada, A. A. , 2000, “The Effect of Creep and Mechanical Load on Cold Expanded Fastener Holes,” Ph.D. thesis, University of Bristol.
10. Measurement of Non-Uniform Residual Stresses Using the Hole Drilling Method. Part I—Stress Calculation Procedures10.1115/1.3226059 ↗
11. Measurement of Non-Uniform Residual Stresses Using the Hole Drilling Method. Part II—Practical Application of the Integral Method10.1115/1.3226060 ↗
12. Kandil, F. A., Lord, J. D., Fry, A. T., and Grant, P. V., 2001, “A Review of Residual Stress Measurement Methods—A Guide to Technique Selection,” Report No. MATC (A) 04, National Physical Laboratory, UK.
13. Grant, P. V., Lord, J. D., and Whitehead, P. S., 2002, “The Measurement of Residual Stresses by the Incremental Hole Drilling Technique,” Measurement Good Practice Guide 53, National Physical Laboratory, UK.
14. Improvements in Residual Stress Measurement by the Incremental Centre Hole Drilling Technique10.1007/s11340-006-7686-8 ↗
15. Measurement and Prediction of Residual Stresses in Thick Section Steel Welds10.1243/0309324001514422 ↗
16. Bonner, N. , 1996, “Measurement of Residual Stresses in Thick Section Steel Welds,” Ph.D. thesis, University of Bristol.
17. Measurement of Through Thickness Stresses Using Small Holes10.1243/0309324021514899 ↗
18. An Integrated Approach for Measuring Near and Sub-Surface Residual Stress in Engineering Components10.1243/0309324041896524 ↗
19. Barber · 104
20. Noyan
21. Hossain, S., Mahmoudi, A. H., Smith, D. J., Stefanescu, D., Truman, C. E., and Withers, P. J., 2004, “The Effect of Proof Loading on Residual Stresses in a Cracked Component,” ESRF Report No. ME622.