journal article·2002-07-01

Distributions of Stretch and Rotation in Polycrystalline OFHC Cu

J. D. Clayton, B. M. Schroeter, D. L. McDowell, S. Graham

Publisher page

Abstract

High resolution experimental characterization of material stretch and rotation fields in relatively fine-grained polycrystals has been limited, inhibiting direct comparison with predictions of crystal plasticity theory. In this study, micron scale grids used more commonly in etching of substrates for microelectronic circuits were deposited on specimens of Oxygen Free High Conductivity Copper (OFHC Cu) subsequently subjected to uniaxial compressive deformations to effective strain levels up to unity. Material stretch and rotation fields were assessed for fields of view encompassing on the order of 20 grains. Some rather striking features emerge, including the apparent relative lack of deformation in regions sized on the order of large grains, and the apparent concentration of stretch and rotation in bands surrounding these relatively undeformed areas. Comparisons are drawn with results of 3D crystal plasticity calculations performed on digitized grain structures that conform to representative microstructures in terms of initial grain size and shape distributions. The crystal plasticity simulations predict regions of relatively large rotation and relatively localized stretch traversing multiple grains. The numerical solutions also exhibit slightly higher local stresses in the vicinity of grain boundaries and triple points than in grain interiors, a phenomenon attributed to local lattice misorientation among neighboring grains. However, the crystal plasticity calculations do not, in an average sense, predict larger-than-average maximum stretch or rotation in the grain boundary regions. The numerical solutions are also quite sensitive to initial lattice orientations assigned to the grains. Comments are made regarding the segmentation of slip within the grains and its implications for modeling, based upon direct comparison of results from experiments and simulations.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Metal Forming Simulation Techniques · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

G.W.W. School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30332

Sandia National Laboratories, Livermore, CA

References (67)

Show source-provided references
1. Kuhlmann-Wilsdorf, D., and Hansen, N., 1991, “Geometrically Necessary, Incidental, and Subgrain Boundaries,” Scr. Metall. Mater., 25, pp. 1557–1562.10.1016/0956-716X(91)90451-6 ↗
2. Bay, B., Hansen, N., Hughes, D. A., and Kuhlmann-Wilsdorf, D., 1992, “Evolution of FCC Deformation Structures in Polyslip,” Acta Metall. Mater., 40, pp. 205–219.10.1016/0956-7151(92)90296-Q ↗
3. Hughes, D. A., Liu, Q., Chrzan, D. C., and Hansen, N., 1997, “Scaling of Microstructural Parameters: Misorientations of Deformation Induced Boundaries,” Acta Mater., 45, pp. 105–112.10.1016/S1359-6454(96)00153-X ↗
4. Kuhlmann-Wilsdorf, D. , 1999, “The Theory of Dislocation-Based Crystal Plasticity,” Philos. Mag., 79, pp. 955–1008.10.1080/01418619908210342 ↗
5. Wilmanski, K., 1991, “Large Elastoplastic Deformation of Two-Phase Alloys-Structural Continuous Model,” Recent Developments in Micromechanics, D. R. Axelrad and W. Muschik, eds., Springer-Verlag, Toronto, pp. 84–96.10.1007/978-3-642-84332-7_7 ↗
6. Driver, J. H. , 1994, “Deformation Texture Formation from Single Crystals,” Mater. Sci. Forum, 157–162, pp. 585–596.10.4028/www.scientific.net/MSF.157-162.585 ↗
7. Leffers, T. , 1994, “Lattice Rotations During Plastic Deformation with Grain Subdivision,” Mater. Sci. Forum, 157–162, pp. 1815–1820.10.4028/www.scientific.net/MSF.157-162.1815 ↗
8. Chang, Y. W., and Asaro, R. J., 1981, “An Experimental Study of Shear Localization in Aluminum-Copper Single Crystals,” Acta Metall., 29, pp. 241–257.10.1016/0001-6160(81)90103-6 ↗
9. Asaro, R. J. , 1985, “Material Modeling and Failure Modes in Metal Plasticity,” Mech. Mater., 4, pp. 343–373.10.1016/0167-6636(85)90032-8 ↗
10. Harren, S. V., De`ve, H. E., and Asaro, R. J., 1988, “Shear Band Formation in Plane Strain Compression,” Acta Metall., 36(9), pp. 2435–2480.10.1016/0001-6160(88)90193-9 ↗
11. Makarov, P. V. , 1992, “Microdynamic Theory of Plasticity and Failure of Structurally Inhomogeneous Media,” Russ. Phys. J., 35(4), pp. 334–346.10.1007/BF00560068 ↗
12. Mescheryakov, Y. I., and Atroshenko, S. A., 1992, “Multiscale Rotations in Dynamically Deformed Solids,” Int. J. Solids Struct., 29, pp. 2761–2778.10.1016/0020-7683(92)90117-C ↗
13. Makarov, P. V., Smolin, I. Y., and Prokopinski, I. P., 1998, “Localized Plastic Strain in Polycrystalline Materials with Hole and Notches,” Theor. Appl. Fract. Mech., 29, pp. 11–20.10.1016/S0167-8442(98)00011-1 ↗
14. Panin, V. E. , 1998, “Overview on Mesomechanics of Plastic Deformation and Fracture of Solids,” Theor. Appl. Fract. Mech., 30, pp. 1–11.10.1016/S0167-8442(98)00038-X ↗
15. Panin, V. E., Deryugin, Y. Y., Derevyagina, L. S., Lotkov, A. I., and Suvorov, B. I., 1998, “Plastic Deformation and Fracture of Polycrystalline Ni-Ti with Stress Concentrators of Different Scales,” Theor. Appl. Fract. Mech., 30, pp. 19–26.10.1016/S0167-8442(98)00040-8 ↗
16. Cherepanov, O. I., Smolin, I. Y., Stefanov, Y. P., and Makarov, P. V., 1999, “Investigation of Influence of Internal Structure of Heterogeneous Materials on Plastic Flow and Fracture,” Comput. Mater. Sci., 16, pp. 25–31.10.1016/S0927-0256(99)00042-7 ↗
17. Zelin, M. G., and Mukherjee, A. K., 1993, “Microstructural Aspects of Non-homogeneity of Grain-boundary Sliding,” J. Mater. Sci., 28, pp. 6767–6773.10.1007/BF00356429 ↗
18. Zelin, M. G., and Mukherjee, A. K., 1994, “Measurements of Spacing of Sliding Grain Boundaries,” J. Mater. Sci., 29, pp. 3607–3611.10.1007/BF00357325 ↗
19. Zelin, M. G., Krasilnikov, N. A., Valiev, R. Z., Grabski, H. S., Yang, H. S., and Mukherjee, A. K., 1994, “On the Microstructural Aspects of the Nonhomogeneity of Superplastic Deformation at the Level of Grain Groups,” Acta Metall. Mater., 42, pp. 119–126.10.1016/0956-7151(94)90054-X ↗
20. Morral, J. E., and Ashby, M. F., 1974, “Dislocated Cellular Structures,” Acta Metall., 22, pp. 567–575.10.1016/0001-6160(74)90154-0 ↗
21. Watanabe, O., Zbib, H. M., and Takenouchi, E., 1988, “Crystal Plasticity: Micro-shear Banding in Polycrystals Using Voronoi Tessellation,” J. Colour Soc., 14, pp. 771–788.10.1016/S0749-6419(98)00022-9 ↗
22. Harren, S. V., and Asaro, R. J., 1989, “Nonuniform Deformations in Polycrystals and Aspects of the Validity of the Taylor Model,” J. Mech. Phys. Solids, 37, pp. 191–232.10.1016/0022-5096(89)90010-0 ↗
23. Havlicek, F., Tokuda, M., Hino, S., and Kratochvil, J., 1992, “Finite Element Method Analysis of Micro-Macro Transition in Polycrystalline Plasticity,” J. Colour Soc., 8, pp. 477–499.10.1016/0749-6419(92)90060-P ↗
24. Harder, J. , 1999, “A Crystallographic Model for the Study of Local Deformation Processes in Polycrystals,” Int. J. Plast., 15, pp. 605–624.10.1016/S0749-6419(99)00002-9 ↗
25. Diepolder, W., Mannl, V., and Mannl, V., 1991, “The Cosserat Continuum: A Model for Grain Rotations in Metals?,” Int. J. Plast., 7, pp. 313–328.10.1016/0749-6419(91)90038-Z ↗
26. Acharya, A., and Bassani, J. L., 2000, “Lattice Incompatibility and a Gradient Theory of Crystal Plasticity,” J. Mech. Phys. Solids, 48, pp. 1565–1595.10.1016/S0022-5096(99)00075-7 ↗
27. Mughrabi, H. , 1983, “Dislocation Wall and Cell Structures and Long-Range Internal Stresses in Deformed Metal Crystals,” Acta Metall., 31(9), pp. 1367–1379.10.1016/0001-6160(83)90007-X ↗
28. Berveiller, M., Muller, D., and Kratochvil, J., 1993, “Nonlocal Versus Local Elastoplastic Behavior of Heterogeneous Materials,” Int. J. Plast. 9, pp. 633–652.10.1016/0749-6419(93)90024-K ↗
29. Butler, G. C., and McDowell, D. L., 1998, “Polycrystal Constraint and Grain Subdivision,” Int. J. Plast., 14(8), pp. 703–717.10.1016/S0749-6419(98)00018-7 ↗
30. Horstemeyer, M. F., and McDowell, D. L., 1998, “Modeling Effects of Dislocation Substructure in Polycrystal Elastoviscoplasticity,” Mech. Mater., 27, pp. 145–163.10.1016/S0167-6636(97)00037-9 ↗
31. McGinty, R. D., and McDowell, D. L., 1999, “Multi-scale Polycrystal Plasticity,” ASME J. Eng. Mater. Technol., 121, pp. 203–209.10.1115/1.2812367 ↗
32. Hayashi, I., Yamazaki, K., and Yamada, N., 1975, “Study on Inhomogeneous Deformation in the Grains of Polycrystalline α-iron—Measurements of Plastic Strain in the Grains by the Grid Line Technique,” Society of Materials. Science, Japan, The 18th Japan Congress on Materials Research-Metallic Materials, pp. 8–14.
33. Tong, W. , 1991, “Detection of Plastic Deformation Patterns in a Binary Aluminum Alloy,” Exp. Mech., 37, pp. 452–459.10.1007/BF02317313 ↗
34. Hughes, D., and Hansen, N., 1991, “Microstructural Evolution in Nickel During Rolling and Torsion,” Mater. Sci. Technol., 7, pp. 544–553.10.1179/026708391790183736 ↗
35. Vendroux, G., and Knauss, W., 1998, “Submicron Deformation Field Measurements: Part 1. Developing a Digital Scanning Tunneling Microscope,” Exp. Mech., 38, pp. 18–23.10.1007/BF02321262 ↗
36. Dally, J., and Riley, W., 1978, Experimental Stress Analysis, McGraw-Hill, New York.10.1115/1.3424473 ↗
37. Du¨rr, R. , 1991, “Displacement Field Analysis: Calculation of Distortion Measures From Displacement Maps,” Ultramicroscopy, 38, pp. 135–141.10.1016/0304-3991(91)90114-L ↗
38. Parks, V. , 1982, “Strain Measurement Using Grids,” Opt. Eng., 21, pp. 633–639.10.1117/12.7972958 ↗
39. Takeda, N. , 1998, “Evaluation of Microscopic Deformation in CFRP Laminates with Delamination by Micro-grid Methods,” J. Compos. Mater., 32, pp. 83–100.10.1177/002199839803200105 ↗
40. Sevenhuijsen, P., Bremand, F., 1993, “Current Trends in Obtaining Deformation Data from Grids,” Exp. Tech., 22, No. 3, pp. 22–26.10.1111/j.1747-1567.1993.tb00747.x ↗
41. Farmer, L., and Fowle, R., 1979, “An Experimental Procedure for Studying the Flow in Plane Strain Extrusion,” Int. J. Mech. Sci., 21(10), pp. 599–608.10.1016/0020-7403(79)90080-8 ↗
42. Goldrein, H., Palmer, S., and Huntley, J., 1995, “Automated Fine Grid Technique for Measurement of Large-Strain Deformation Maps,” Opt. Lasers Eng., 23, pp. 305–318.10.1016/0143-8166(95)00036-N ↗
43. Wolak, J., and Parks, V., 1974, “Evaluation of Large Strains in Industrial Applications,” J. Test. Eval., 2, pp. 533–540.10.1520/JTE11688J ↗
44. Durelli, A., and Parks, V., 1970, Moire´ Analysis of Strain, Prentice-Hall, New Jersey.
45. Peters, W., and Ranson, W., 1982, “Digital Imaging Techniques in Experimental Stress Analysis,” Opt. Eng., 21, pp. 427–431.10.1117/12.7972925 ↗
46. Graham, S., 1995, “Mechanical Behavior of FCC Polycrystals Under Complex Loading at Finite Strain,” M.S. thesis, GWW School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA.
47. Christodoulou, N., and Jonas, J., 1985, “Flow Localization in OFHC Cu and 99.9% Al,” Acta Metall., 33, pp. 719–730.10.1016/0001-6160(85)90036-7 ↗
48. Sowerby, R., Duncan, J., and Chu, E., 1986, “The Modeling of Sheet Metal Stampings,” Int. J. Mech. Sci., 28, pp. 415–430.10.1016/0020-7403(86)90062-7 ↗
49. Boyce, D., 1999, LASI6 v6.1.6.0, LASI Integrated Circuit CAD for Windows 95, 98, NT4, 2000 and ME.
50. Ohki, H., Nakazawa, H., Kosaka, Y., Sato, H., Asari, T., and Isobe, M., 1987, “Fabrication of Fine and Smooth Curved Features by E-beam Lithography System,” Microelectronic Engineering, Proceedings of the International Conference on Microlithography, Vol. 6, No. 1–4, pp. 207–212.10.1016/0167-9317(87)90039-6 ↗
51. Asaro, R. J. , 1983, “Crystal Plasticity,” ASME J. Appl. Mech., 50, pp. 921–934.10.1115/1.3167205 ↗
52. Bammann, D. J., and Johnson, G. C., 1987, “On the Kinematics of Finite-deformation Plasticity,” Acta Mech., 70, pp. 1–13.10.1007/BF01174643 ↗
53. Horstemeyer, M. F., McDowell, D. L., and McGinty, R. D., 1999, “Design of Experiments for Constitutive Model Selection: Application to Polycrystal Elastoviscoplasticity,” Microgravity Sci. Technol., 7, pp. 253–273.10.1088/0965-0393/7/2/008 ↗
54. ABAQUS, 1998, version 5.8–14, Hibbitt, Karlsson, & Sorensen, Inc., Pawtucket, RI.
55. P. J. Armstrong, and C. O. Frederick, 1966, CEGB Report, RD/B/N, p. 731.
56. Lacy, T. E., McDowell, D. L., and Talreja, R., 1999, “Gradient Concepts for Evolution of Damage,” Mech. Mater., 31, pp. 831–860.10.1016/S0167-6636(99)00029-0 ↗
57. Nagtegaal, J. C., Parks, D. M., and Rice, J. R., 1974, “On Numerically Accurate Finite Element Solutions in the Fully Plastic Range,” Comput. Methods Appl. Mech. Eng., 4, pp. 153–177.10.1016/0045-7825(74)90032-2 ↗
58. Humphreys, F. J. , 2001, “Grain and Subgrain Characterization by Electron Backscatter Diffraction,” J. Mater. Sci., 36, pp. 3833–3854.10.1023/A:1017973432592 ↗
59. Davis, J. R., ed., 1998, ASM Metals Handbook, Desk Edition, Second Edition, ASM International, Materials Park, OH.10.31399/asm.hb.mhde2.9781627081993 ↗
60. Barbe, F., Forest, S., and Cailletaud, G., 2001, “Intergranular and Intragranular Behavior of Polycrystalline Aggregates. Part 2: Results,” Int. J. Plast., 17, pp. 537–563.10.1016/S0749-6419(00)00062-0 ↗
61. Cailletaud, G., 2001, personal communication.
62. Sarma, G., Radhakrishnan, B., and Zacharia, T., 1999, “Modelling the Deformation of Face Centered Cubic Crystals to Study the Effect of Slip on {110} Planes,” Modell. Simul. Mater. Sci. Eng., 7, pp. 1025–1043.10.1088/0965-0393/7/6/308 ↗
63. Bhattacharyya, A., El-Danaf, E., Kalidindi, S. R., and Doherty, R. D., 2001, “Evolution of Grain-scale Microstructure During Large Strain Simple Compression of Polycrystalline Aluminum with Quasi-columnar Grains: OIM Measurements and Numerical Simulations,” Int. J. Plast., 17, pp. 861–883.10.1016/S0749-6419(00)00072-3 ↗
64. Ziegenbein, A., Neuha¨user, H., Thesing, J., Ritter, R., Wittich, H., Steck, E., Springer, F., and Schwarzer, R. A., 1998, “Investigations on Local Plasticity of CuAl Polycrystals by in situ Observations and FEM Simulations,” Mater. Sci. Forum, 273–275, pp. 363–368.10.4028/www.scientific.net/MSF.273-275.363 ↗
65. Anand, L., and Kalidindi, S. R., 1994, “The Process of Shear Band Formation in Plane Strain Compression of FCC Metals: Effects of Crystallographic Texture,” Mech. Mater., 17, pp. 223–243.10.1016/0167-6636(94)90062-0 ↗
66. Ashmawi, W. M., and Zikry, M. A., 2000, “Effects of Grain Boundaries and Dislocation Density Evolution on Large Strain Deformation Modes in FCC Crystalline Metals,” J. Comput.-Aided Mater. Des., 7, pp. 55–62.10.1023/A:1008717428264 ↗
67. Shen, Y.-L., Li, W., Sulsky, D. L., and Schreyer, H. L., 2000, “Localization of Plastic Deformation Along Grain Boundaries in a Hardening Material,” Int. J. Mech. Sci., 42, pp. 2167–2189.10.1016/S0020-7403(00)00005-9 ↗