journal article·2006-10-01

Experimentally Evaluating the Equilibrium Stress in Shear of Glassy Polycarbonate

Mehrdad Negahban, Ashwani Goel, Pierre Delabarre, Ruqiang Feng, Amy Dimick

Publisher page

Abstract

One group of models proposed for characterizing the mechanical response of glassy polymers is based on a structure that resembles finite plasticity. In most cases, a constitutive equation for stress is proposed, which depends on the elastic deformation gradient, supplemented by a flow rule for the plastic deformation, which depends on the “over stress.” The over stress is a properly invariant difference between the stress and the back stress (equilibrium stress). The back stress represents conditions under which relaxation events should stop and the material should be able to carry an applied load indefinitely without a need to change the strain. Questions that arise in using these models are whether such equilibrium stresses exist, how can they be evaluated, and what experiments can be used to characterize the flow rule. One challenge in accurately evaluating the locus of equilibrium conditions is the fact that the relaxation process substantially slow down around these points, and, therefore, a method that does not directly require being at the equilibrium is desirable. Focusing on shear, a thermodynamic theory for characterizing the response of glassy polymers, similar to models currently used for this purpose, is developed, and using this model it is shown that one can set up a method to calculate the plastic strain rate. This method is based on evaluating the slope of stress-strain response under conditions of similar elastic and plastic strain, but different strain rates. Since the equilibrium stress occurs when the plastic strain rate goes to zero, the evaluated plastic strain rates allow evaluation of the needed information for developing the flow rule and obtaining the back stress. This method is used to evaluate the plastic strain rate and back stress at room temperature for polycarbonate. The evaluated results match well with results obtained by direct probing of the equilibrium stress, in which one searches for points at which the stress remains constant at a constant strain over long durations. The method proposed looks promising in evaluating the back stress of glassy polymers. The added advantage of this method is that it also provides a map of plastic strain rate and tangent modulus over a large range of loading conditions.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Polymer crystallization and properties · Polymer Nanocomposites and Properties · Polymer Foaming and Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Engineering Mechanics, University of Nebraska, Lincoln, NE 68588-0526

References (19)

Show source-provided references
1. Plastic Deformation in Glassy Polymers
2. Plastic Flow in Glassy Polymers10.1002/pen.760170306 ↗
3. Plastic Deformation in Polyimides, With New Implications on the Theory of Plastic Deformation of Glassy Polymers10.1080/14786437708232634 ↗
4. Large Inelastic Deformation of Glassy Polymers. Part I: Rate Dependent Constitutive Model10.1016/0167-6636(88)90003-8 ↗
5. Plastic Flow in Oriented Glassy Polymers10.1016/0749-6419(89)90003-X ↗
6. An Experimental and Analytical Investigation of the Large Strain Compressive and Tensile Response of Glassy Polymers10.1002/pen.760302005 ↗
7. Evolution of Plastic Anisotropy in Amorphous Polymers During Finite Stretch
8. Strain Rate and Temperature Dependence in Amorphous Polymers at Finite Strain
9. Effects of Initial Anisotropy on the Finite Strain Deformation Behavior of Glassy Polymers10.1016/0749-6419(93)90052-R ↗
10. The Large Strain Compression, Tension, and Simple Shear of Polycarbonate10.1002/pen.760340904 ↗
11. Effects of Strain Rate, Temperature and Thermomechanical Coupling on the Finite Strain Deformation of Glassy Polymers10.1016/0167-6636(94)00034-E ↗
12. Constitutive Model for the Nonlinear Viscoelastic Viscoplastic Behavior of Glassy Polymers10.1002/pen.760350407 ↗
13. Effects of Strain Rate, Temperature and Thermo-Mechanical Coupling on the Finite Strain Deformation of Glassy Polymers10.1016/0167-6636(94)00034-E ↗
14. Overstress Model for Solid Polymer Deformation Behavior Applied to Nylon 6610.1002/pen.760350405 ↗
15. Krempl, E., and Bordonaro, C. M., 2000, “State Variable Model for High Strength Polymers,” ASTM Special Technical Publication, pp. 118–137.
16. Rate (Time)-Dependent Deformation Behavior: An Overview of Some Properties of Metals and Solid Polymers10.1016/S0749-6419(03)00002-0 ↗
17. Pre-Necking and Post-Necking Relaxation and Creep Behavior of Polycarbonate: A Phenomenological Study
18. Preliminary Results on an Effort to Characterize Thermo-Mechanical Response of Amorphous Polymers in the Glass-Transition Range
19. Measurement and Modeling of Back Stress at Intermediate to High Homologous Temperatures10.1016/S0749-6419(99)00055-8 ↗