journal article·2005-01-01

Fatigue of As-Fabricated Open Cell Aluminum Foams

J. Zhou, Z. Gao, A. M. Cuitino, W. O. Soboyejo

Publisher page

Abstract

This paper presents the results of the combined experimental investigation and digital image correlation (DIC) analysis of the fatigue failure of open cell aluminum foams. Compression–compression cyclic loads were applied to foam specimens under the as-fabricated condition. Following characterization of the S-N curve behavior, the macroscale deformation of the tested foam under fatigue was recorded using an in-situ digital camera. The deformation sequence was then analyzed using DIC technique. It was found that foams failed with an abrupt strain jump when shear bands were formed, and serious deformation up to more than 30% was developed in the center of the shear band. The ex-situ scanning electron microscopy analysis indicated that the abrupt strain jump was due to the microscale damage accumulation in struts where surface cracks were formed and propagated.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Cellular and Composite Structures · Mechanical Behavior of Composites · Automotive and Human Injury Biomechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Princeton Materials Institute and The Department of Mechanical and Aerospace Engineering, Princeton University, Olden Street, Princeton, NJ 08540

The Department of Mechanical and Aerospace Engineering, Rutgers University Piscataway, NJ 08854

References (11)

Show source-provided references
1. Ashby, M. F., Evans, A. G., Fleck, N. A., Gibson, L. J., Hutchinson, J. W. and Wadley, H. N. G., 2000, Metal Foams-A Design Guide, Butterworth-Heinemann, London.10.1115/1.1421119 ↗
2. Gibson, L. J., and Ashby, M. F., 1997, Cellular Solids: Structure and Properties, end ed., Combridge University Press, Cambridge, UK.10.1017/CBO9781139878326 ↗
3. Gibson, L. J. , 2001, “Mechanical Behavior of Metallic Foams,” Annu. Rev. Mater. Sci., 30, pp. 191–227.10.1146/annurev.matsci.30.1.191 ↗
4. Banhart, John , 2001, “Manufacture, Characterization and Application of Cellular Metals and Metal Foams,” Prog. Mater. Sci., 46, pp. 559–632.10.1016/S0079-6425(00)00002-5 ↗
5. Sugimura, Y., Rabiei, A., Evans, A. G., Harte, A. M., and Fleck, N. A., 1999, “Compression Fatigue of a Cellular Aluminum Alloy,” Mater. Sci. Eng., A, 269, pp. 38–48.10.1016/S0921-5093(99)00147-1 ↗
6. Banhart, J., and Brinkers, W., 1999, “Fatigue Behavior of Aluminum Foams,” J. Mater. Sci. Lett., 18, pp. 617–619.10.1023/A:1006646901741 ↗
7. McCullogh, K. Y. G., Fleck, N. A., and Ashby, M. F., 2000, “The Stress-Life Fatigue Behavior of Aluminum Alloy Foams,” Fatigue Fract. Eng. Mater. Struct., 23, pp. 199–208.10.1046/j.1460-2695.2000.00261.x ↗
8. Zettl, B., Mayer, H., Stanzl-Tschegg, S. E., and Degischer, H. P., 2000, “Fatigue Properties of Aluminum Foams at High Numbers of Cycles,” Mater. Sci. Eng., A, 292, pp. 1–7.10.1016/S0921-5093(00)01033-9 ↗
9. Lehmhus, D., Marschner, C., and Banhart, J., 2002, “Influence of Heat Treatment on Compression Fatigue of Aluminum Foams,” J. Mater. Sci., 37, pp. 3447–3451.10.1023/A:1016506905271 ↗
10. Harte, A-M., Fleck, N. A., and Ashby, M. F., 1999, “Fatigue Failure of an Open Cell and a Closed Cell Aluminum Alloy Foam,” Acta Mater., 47, pp. 2511–2524.10.1016/S1359-6454(99)00097-X ↗
11. Zhou, J., Shrotriya, P., and Soboyejo, W. O., 2003, “Mechanisms and Mechanics of Compressive Deformation in Open-Celled Al Foams,” Mech. Mater., in press.10.1016/j.mechmat.2003.05.004 ↗