journal article·2002-10-01

Experimental Method for Residual Stress Evaluation Through the Thickness of a Plate

Lars Fuglsang Andersen

Publisher page

Abstract

In the present work an experimental method is developed for residual stress evaluation in medium thick plates. On the basis of the incremental hole-drilling technique, a method to resolve the in-plane residual stresses through the plate thickness is given. An analysis of the hole-drilling configuration is carried out, resulting in a configuration which optimizes the stress calculation accuracy. Moreover, it is estimated that conventional milling can be applied without affecting the accuracy of the method. Finally, the results of a comprehensive stress calculation error analysis are presented.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced machining processes and optimization · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Naval Architecture & Offshore Engineering, Technical University of Denmark, DK-2800 Lyngby, Denmark

References (10)

Show source-provided references
1. Andersen, L. F., 2000, “Residual Stresses and Deformations in Steel Structures,” PhD thesis, Department of Naval Architecture and Offshore Engineering, Technical University of Denmark.
2. Bijak-Zochowski, M. , 1978, “A Semi Destructive Method of Measuring Residual Stresses,” VDI-Ber., 313, pp. 469–476.
3. Flaman, M. T., and Manning, B. H., 1985, “Determination of Residual Stress Variation with Depth by the Hole-Drilling Method,” Exp. Mech., 25, No. 2, pp. 205–207.10.1007/BF02325088 ↗
4. Niku-Lari, A., Lu, J., and Flavenot, J. F., 1985, “Measurement of Residual Stress Distribution by the Incremental Hole-Drilling Method,” Exp. Mech., 25, pp. 175–185.10.1007/BF02328809 ↗
5. Shajer, G. , 1981, “Application of Finite Element Calculations to Residual Stress Measurements,” ASME J. Eng. Mater. Technol., 103, pp. 157–163.10.1115/1.3224988 ↗
6. Shajer, G. , 1988, “Measurements of Non-uniform Residual Stresses Using the Hole-Drilling Method. Part I—Stress Calculation Procedures,” ASME J. Eng. Mater. Technol., 110, pp. 338–343.10.1115/1.3226059 ↗
7. Shajer, G., and Altus, E., 1996, “Stress Calculation Error Analysis for Incremental Hole-Drilling Residual Stress Measurements,” ASME J. Eng. Mater. Technol., 118, pp. 120–126.10.1115/1.2805924 ↗
8. Shajer, G. , 1998, “Measurements of Non-uniform Residual Stresses Using the Hole-Drilling Method. Part II—Practical Application of the Method,” ASME J. Eng. Mater. Technol., 110, pp. 344–349.10.1115/1.3226060 ↗
9. Nawwar, A., McLachlan, K., and Shewchuck, J., 1976, “A Modified Hole-Drilling Technique for Determining Residual Stresses in Thin Plates,” Exp. Mech., 6(6), pp. 226–232.10.1007/BF02329273 ↗
10. Flaman, M. T. , 1982, “Brief Investigation of Induced Drilling Stresses in the Center-hole Method of Residual Stress Measurement,” Exp. Mech., 22, No. 1, pp. 26–30.10.1007/BF02325700 ↗