Finite Element Thermal/Mechanical Analysis of Transmission Laser Microjoining of Titanium and Polyimide
Source abstract
Abstract
Detailed analysis of a residual stress profile due to laser microjoining of two dissimilar biocompatible materials, polyimide (PI) and titanium (Ti), is vital for the long-term application of bio-implants. In this work, a comprehensive three-dimensional (3D) transient model for sequentially coupled thermal/mechanical analysis of transmission laser (laser beam with wavelength of 1100 nm and diameter of 0.2 mm) microjoining of two dissimilar materials has been developed by using the finite element code ABAQUS, along with a moving Gaussian laser heat source. First the model has been used to optimize the laser parameters like laser traveling speed and power to obtain good bonding (burnout temperature of PI>maximum temperature of PI achieved during heating>melting temperature of PI) and a good combination has been found to be 100 mm/min and 3.14 W for a joint-length of 6.5 mm as supported by the experiment. The developed computational model has been observed to generate a bonding zone that is similar in width (0.33 mm) to the bond width of the Ti/PI joint observed experimentally by an optical microscope. The maximum temperatures measured at three locations by thermocouples have also been found to be similar to those observed computationally. After these verifications, the residual stress profile of the laser microjoint (100 mm/min and 3.14 W) has been calculated using the developed model with the system cooling down to room temperature. The residual stress profiles on the PI surface have shown low value near the centerline of the laser travel, increased to higher values at about 165 μm from the centerline symmetrically at both sides, and to the contrary, have shown higher values near the centerline on the Ti surface. Maximum residual stresses on both the Ti and PI surfaces are obtained at the end of laser travel, and are in the orders of the yield stresses of the respective materials. It has been explained that the patterned accumulation of residual stresses is due to the thermal expansion and contraction mismatches between the dissimilar materials at the opposite sides of the bond along with the melting and softening of PI during the joining process.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Laser Material Processing Techniques · Advanced machining processes and optimization · Laser and Thermal Forming Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Wayne State University, Detroit, MI
Department of Electrical and Computer Engineering, Wayne State University, Detroit, MI
Institute for Manufacturing Research, Wayne State University, Detroit, MI 48202
Department of Mechanical Engineering, Institute for Manufacturing Research, and Department of Biomedical Engineering, Wayne State University, Detroit, MI
Fraunhofer Center for Laser Technology, Plymouth, MI 48170
References (16)
Show source-provided references
1. A Point and Line Source Model of Laser Keyhole Welding10.1088/0022-3727/21/8/002 ↗
2. Heat Transfer Model for CW Laser Material Processing10.1063/1.327672 ↗
3. Keynote Address: Modeling Thermal Stresses and Distortions in Welds
4. Finite Element Modeling of Transmission Laser Microjoining Process10.1016/j.jmatprotec.2006.11.225 ↗
5. Research Progress of Subretinal Implant Based on Electronic Stimulation
6. An XPS Study of Laser-Fabricated Polyimide/Titanium Interface10.1016/j.apsusc.2004.03.261 ↗
7. Temperature Distributions Produced in a Two Layer Structure by a Scanning CW Laser or Electron Beam10.1063/1.331216 ↗
8. Habbitt, Karlesson and Sorensen, Inc., 2004, ABAQUS version 6.5 User’s Manual and Documentations.
9. Cook
10. Zienkiwicz
11. Heat Transfer and Residual Stress Modeling of a Diamond Film Heat Sink for High Power Laser Diodes10.1109/TCAPT.2003.817649 ↗
12. An Empirical Analysis of Titanium Stress-Strain Curves10.1007/BF02645603 ↗
13. Characterization Study of Time- and Temperature-Dependent Mechanical Behavior of Polyimide Materials in Electronics Packaging Applications10.1007/s11664-005-0213-3 ↗
14. Four Decades of Research on Thermal Contact, Gap, and Joint Resistance in Microelectronics10.1109/TCAPT.2005.848483 ↗
15. Sultana, T. , 2007, “Bond Quality and Failure Mode Assessment for Polymer-Metal and Polymer-Glass Transmission Laser Joints,” Ph.D. thesis, Wayne State University, Detroit, MI.
16. http://www.matweb.com/.