Analysis of Mass Transfer Process in the Pore Free Technique
Source abstract
Abstract
Air entrainment is one of the most significant problems in pressure die casting. A possible solution is to use the Pore Free technique. In this technique an oxygen is introduced into the die to react with the liquid metal. The vacuum created by the reaction reduces the porosity. The life span of the mold is augmented by the reduction of the pressure during the process. In some cases the Pore Free technique yields acceptable results, i.e., low porosity, while in other cases the results are not satisfactory. These differing results can be explained by an analysis of the mechanisms involved. A simple model is proposed based on conservation laws that describes the relationship between mass transfer mechanisms and pressure deviation. The model indicates that there is a critical dimensionless parameter above which the pressure is decreased and below which the pressure is increased. In the first case, when the parameter exceeds the critical value, the technique is useful. In the second case, when the parameter is less than the critical value, introducing oxygen does not greatly reduce the porosity. The analysis demonstrates that the Pore Free and vacuum venting techniques account for two different extremes. The first case is when the flow is orderly throughout the chamber in which vacuum venting can produce acceptable results. The second case is when the flow is turbulent and the Pore Free technique is the better choice.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Injection Molding Process and Properties · Metal Forming Simulation Techniques · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455
References (14)
Show source-provided references
1. Allsop, D. F., 1983, Pressure DieCasting Part 2: The Technology of the Casting and The Die, Pergamon Press, Oxford.
2. ASM International, 1987, Metals Handbook, ninth edition, Metals Park, Ohio., Vol. 13, pp. 61–76.
3. Bar-Meir, G., Eckert, E. R. G., and Goldstein, R. J., 1993a, “Pressure Die Casting: A Model of Air Venting,” MSI report no. 93/84, May.
4. Bar-Meir, G., Eckert, E. R. G., and Goldstein, R. J., 1993b, “Pressure Die Casting: A Model of Vacuum Pumping,” ASME Journal of Engineering for Industry, in press (also a short version was presented at the 17th International Die Casting Congress in Cleveland Ohio, Oct. 18–21. 1993).
5. Brauner N. , MaolemD., and MeyersonG., 1988, “The Effect of Absorbate Concentration Level in Hygroscopic Condensation,” Int. Comm. Heat Mass Transfer, Vol. 15, pp. 269–279.10.1016/0735-1933(88)90028-0 ↗
6. Brauner N. , MaolemD., MeyersonG., 1989, “Coupled Heat Condensation and Mass Absorption with Comparable Concentrations of Absorbate and Absorbent,” International Journal of Heat and Mass Transfer, Vol. 32, No. 10, pp. 1897–1906.10.1016/0017-9310(89)90159-2 ↗
7. Cussler, E. L., 1984, Diffusion Mass Transfer in Fluid Systems, Cambridge University Press, Cambridge, pp. 325–333.
8. Eckert E. R. G. , 1989, “Similarity Analysis Applied to the Die Casting Process,” ASME Journal op Engineering Materials and Technology, Vol. 111, No. 4, Oct., pp. 393–398.10.1115/1.3226485 ↗
9. Herrschaft, D. C., 1976, “Pore-Free Die Casting—Its Impact on Automotive Hardware,” American Society for Metals, Report system paper No. 76–15, October 28th.
10. Kaye, A., and Street, A., 1982, Die Casting Metallurgy, Butterworty Scientific, London, p. 213.10.1016/B978-0-408-10717-4.50020-1 ↗
11. Lefebvre, A. H., 1989, Atomization and Sprays, Hemisphere Publishing, New York.10.1201/9781482227857 ↗
12. Lindsey, D., and Wallace, J. F., 1972, “Effect of Vent Size and Design, Lubrication Practice, Metal Degassing, Die Texturing and Filling of Shot Sleeve on Die Casting Soundness,” paper 10372, Transactions, 7th SDCE International Die Casting Congress, pp. 1–15.
13. Lewis G. P. , CrawD. A., and BellR. C., 1961, “Porosity in Zinc Die Casing,” Transactions of the American Foundrymen’s Society, Vol. 69, pp. 537–548.
14. Maier, R. D., 1974, “Influence of Liquid Metal Jet Character on Heat Transfer During Die Casting,” Ph.D. dissertation. Case Western Reserve University.