Effect of Surface Asperity on Interfacial Contact Process Controlled by Power Law Creep—Numerical Study of Viscoplastic Adhering Process
Source abstract
Abstract
An interfacial contact process due to power law creep is studied using a finite element technique. The contact process is assumed to be produced by power law creep alone after initial intimate contact by instantaneous plastic deformation, i.e., no diffusional mechanisms for void shrinkage are taken into account. Also, the surface oxide film is not considered. If the bonded material is deformed, then the deformation is influenced by the initial faying surface wauiness with the asperity angle αo, and the contact process is achieved by two modes; surface folding at the bond-interface (type I) and interfacial expansion (type II), where the surface folding is the phenomenon that two faying surfaces are overlapped to each other. The surface folding phenomenon occurs preferentially when αo is less than 30 deg (as the surface wauiness height decreases). On the other hand, the interfacial expansion is dominant at αo > 45 deg. This can be explained in terms of the distribution of equivalent strain (stress) in the vicinity of the bond-interface.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Adhesion, Friction, and Surface Interactions · Metal and Thin Film Mechanics · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Welding Research Institute of Osaka University, Mihogaoka 11-1, Ibaraki 567, Japan
Osaka University, Ibarahi, Japan
References (12)
Show source-provided references
1. Enjo T. , IkeuchiK., and AkikawaN., 1982, “Effect of The Roughness of Faying Surface on The Early Process of Diffusion Welding,” J. Jap. Weld. Soc., Vol. 51, No. 12, pp. 1028–1035.
2. Garmong G. , PatonN. E., and ArgonA. S., 1975, “Attainment of Full Interfacial Contact During Diffusion Bonding,” Metall. Trans., Vol. 6A, pp. 1269–1279.10.1007/BF02641912 ↗
3. Hamilton, C. H., 1973, “Pressure Requirements for Diffusion Bonding of Metals,” Titanium Sci. and Tech., R. I. Jaffee and H. H. Burte, eds., Vol. 1, Plenum Press, New York, pp. 625–648.10.1007/978-1-4757-1346-6_46 ↗
4. Hill A. , and WallachE. R., 1989, “Modelling Solid State Diffusion Bonding,” Acta Metall., Vol. 37, pp. 2425–2437.10.1016/0001-6160(89)90040-0 ↗
5. Hill, R., 1950, The Mathematical Theory of Plasticity, Oxford at the Clarendon Press, London, pp. 213–226.
6. Nishiguchi K. , and TakahashiY., 1985, “A Quantitative Analysis of Solid State Bonding Process Based on Fundamental Bonding Mechanisms,” Quarterly J. Japan Weld. Soc., Vol. 3, pp. 303–315.10.2207/qjjws.3.303 ↗
7. Ohashi O. , and HashimotoT., 1976, “Study on Diffusion Welding (Report 1),” J. Jap. Weld. Soc., Vol. 45, No. 1, pp. 78–81.10.2207/qjjws1943.45.76 ↗
8. Takahashi Y. , and InoueK., 1992, “Recent Void Shrinkage Models and Their Applicability to Diffusion Bonding,” Mater. Sci. and Tech., Vol. 8, pp. 953–964.10.1179/026708392790409789 ↗
9. Takahashi Y. , KoguchiT., and NishiguchiK., 1993a, “Modeling of Viscoplastic Adhering Process by a Finite Element Technique,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 115, pp. 150–155.10.1115/1.2902149 ↗
10. Takahashi Y. , KoguchiT., and NishiguchiK., 1993b, “Effect of Bulk Deformation on Viscoplastic Adhering Process—A Numerical Study of Solid State Pressure Welding,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 115, pp. 171–178.10.1115/1.2904203 ↗
11. Tomita Y. , and SowerbyR., 1978, “An Approximate Analysis for Studying the Deformation Mechanics of Rate Sensitive Materials,” Int. J. Mech. Sci., Vol. 20, pp. 361–371.10.1016/0020-7403(78)90039-5 ↗
12. Wilkinson D. S. , and AshbyM. F., 1975, “Pressure Sintering by Power Law Creep,” Acta Metall., Vol. 23, pp. 1277–1285.10.1016/0001-6160(75)90136-4 ↗