An Experimental Investigation of Resin Flow Sensing During Molding Processes
Source abstract
Abstract
The present investigation focused on the need for sensing subsystems for the monitoring of resin flow dynamics during molding processes. Such subsystems, when combined with process parameter control, will produce intelligent manufacturing systems that could significantly improve manufacturing capabilities. A concise review of potential resin flow monitoring methodologies is included, and a detailed analysis of one particular sensing concept originally investigated at the U. S. Army Materials Technology Laboratory is presented. The concept is based on embedded electronic sensors, and during the present study a resin front monitoring system based on a modified version of this concept was developed. Electrically conductive wires were embedded orthogonally in a nonintersecting manner within mold cavities. Subsequent resin flow was sensed by monitoring the electrical characteristics of circuits which resulted during processing. A novel modification of circuitry was included to allow for the monitoring at multiple locations with a single electronic circuit. The net result of this modification was an improved response time of the overall sensing subsystem. The concept was verified experimentally through the performance of both one-dimensional (TD) and two-dimensional (2-D) experiments. The resin system utilized consisted of a mixture of epoxy resin (EPON 826) and a curing agent (MHHPA). The sensed flow front progression information was validated through controlled injection rate experimentation and flow visualization results obtained with transparent molds. It was concluded that the resin flow sensing subsystem could be applied to relatively slow molding processes. Positive and negative aspects related to the applicability of the sensing method to actual manufacturing processes are discussed.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Epoxy Resin Curing Processes · Injection Molding Process and Properties · Electronic Packaging and Soldering Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Intelligent Materials and Manufacturing Laboratory, Department of Mechanical Engineering and Mechanics, Lehigh University, Bethlehem, PA 18015
References (21)
Show source-provided references
1. Adams K. L. , MillerB., and RebenfeldL., 1986, “Forced In-plane Flow of an Epoxy Resin in Fibrous Network,” Journal of Polymer Engineering and Science, Vol. 26, No. 20, pp. 1434–1440.10.1002/pen.760262013 ↗
2. Coulter, J. P., and Guceri, S. I., 1988, “Resin Transfer Molding: Process Review, Modeling and Research Opportunities,” Proceedings of Manufacturing International ’88, American Society of Mechanical Engineers, New York, Vol. 1, pp. 79–85.
3. Coulter, J. P., Smith, B. F., and Guceri, S. I., 1987, “Experimental and Numerical Analysis of Resin Impregnation during the Manufacturing of Composite Materials,” Proceedings of the American Society for Composites, Second Technical Conference, R. L. McCullough and D. W. Wilson, eds., Technomic Publishing Company, Inc., Lancaster, Pa., pp. 209–217.
4. Coulter J. P. , BurkeL. I., and DemirciH. H., 1993, “Neural Networks in Material Processing and Manufacturing: A Review,” Journal of Materials Processing & Manufacturing Science, Vol. 1, No. 4, pp. 431–444.
5. Dave R. , 1990, “A Unified Approach to Modeling Resin Flow During Composite Processing,” Journal of Composite Materials, Vol. 24, No. 1, pp. 22–41.10.1177/002199839002400102 ↗
6. Demirci H. H. , and CoulterJ. P., 1993, “Neural Network based Intelligent Control of Molding Processes,” Journal of Materials Processing and Manufacturing Science, Vol. 2, No. 3, pp. 335–354.
7. Fracchia, C. A., Castro, J., and Tucker, C. L. III, 1989, “A Finite Element/Control Volume Simulation of Resin Transfer Mold Filling,” Proceedings of the American Society for Composites, Fourth Technical Conference, K. Reifsniter, eds., Technomic Publishing Company, Lancaster, Pa., pp. 157–166.
8. Gauvin R. , ChibaniM., and LafontaineP., 1987, “The Modeling of Pressure Distribution in Resin Transfer Molding,” Journal of Reinforced Plastics and Composites, Vol. 6, No. 5, pp. 367–377.10.1177/073168448700600406 ↗
9. Gauvin R. , and ChibaniM., 1990, “A Study of Permeability of Non-woven Reinforcement in Composite Molding,” Society for Advancement of Materials and Process Engineering Quarterly, Vol. 21, No. 3, pp. 52–58.
10. Hart, S., Kranbuehl, D., Loos, A., Hinds, B., and Koury, J., 1992, “Intelligent Sensor-model Automated Control of PMR-15 Autoclave Processing,” 37th International Society for the Advancement of Materials and Process Engineering Symposium, G. C. Girimes, R. Turpin, C. Forberg, B. Rasmussen, and J. Whitney, eds., Society for the Advancement of Materials and Process Engineering, Covina, Ca., pp. 224–230.
11. Hayward J. S. , and HarrisB., 1990, “Effect of Process Variables on the Quality of RTM Moulding,” Society for the Advancement of Materials and Process Engineering Journal, Vol. 26, No. 3, pp. 39–46.
12. Kranbuehl D. , DelosS., YiE., MayerJ., and JarvieT., 1986a, “Dynamic Dielectric Analysis: Nondestructive Material Evaluation and Cure Cycle Monitoring,” Journal of Polymer Engineering and Science, Vol. 26, No. 5, pp. 338–345.10.1002/pen.760260503 ↗
13. Kranbuehl D. E. , DelosS. E., and JueP. K., 1986b, “Dielectric Properties of the Polymerization of an Aromatic Polyimide,” Polymer, Vol. 27, No. 1, pp. 11–18.10.1016/0032-3861(86)90350-2 ↗
14. Kranbuehl, D., Delos, S., Hoff, M., Weller, L., Haverty, P., and Seeley, J., 1987, “Dynamic Dielectric Analysis: Monitoring the Chemistry and Rheology During Cure of Thermosets,” Proceedings of the American Chemical Society Division of Polymeric Materials: Science and Engineering, American Chemical Society, Washington, D.C., Vol. 56, pp. 163–168.
15. Kranbuehl, D., Hoff, M., Eichenger, D., Hamilton, T., and Clark, R., 1988, “Frequency Dependent Electromagnetic Sensing: Life Monitoring of Materials During Use in Space,” Proceedings of the Fall Meeting of the American Chemical Society Division of Polymeric Materials: Science and Engineering, American Chemical Society, Washington, D.C., Vol. 59, pp. 839–843.
16. Kranbuehl D. , DelosS., HoffM., and HavertyP., 1989a, “Use of the Frequency Dependence of the Impedance to Monitor Viscosity During Cure,” Journal of Polymer Engineering and Science, Vol. 29, No. 5, pp. 285–289.10.1002/pen.760290504 ↗
17. Kranbuehl D. E. , HavertyP., and HoffM., 1989b, “Monitoring the Cure Processing Properties of Unsaturated Polyesters in situ During Fabrication,” Journal of Polymer Engineering and Science, Vol. 29, No. 15, pp. 988–992.10.1002/pen.760291504 ↗
18. Kranbuehl, D. E., 1990, “In-situ Cure Monitoring of Coatings for Plastics,” Proceedings of the American Chemical Society Division of Polymeric Materials: Science and Engineering, American Chemical Society, Washington, D.C., Vol. 63, pp. 90–93.
19. Kranbuehl, D., Kingsley, P., Hart, S., Loos, A., Hasko, G., and Dexter, B., 1992, “Sensor-model Prediction, Monitoring and In-situ Control of Liquid RTM Advanced Fiber Architecture Composite Processing,” 37th International Society for the Advancement of Materials and Process Engineering Symposium, G. C. Girimes, R. Turpin, C. Forsberg, B. Rasmussen, and J. Whitney, eds., Society for the Advancement of Materials and Process Engineering, Covina, Ca., pp. 907–913.
20. Martin, G. Q., and Son, J. S., 1986, “Fluid Mechanics of Mold Filling for Fiber Reinforced Plastics,” Advanced Composites: The Latest Developments, P. Beardmore, and C. F. Johnson, eds., ASM International, Dearborn, Mi., pp. 149–158.
21. Walsh, S. M., 1990, “Artificial Intelligence: Its Application to Composite Processing,” 35th International Society for the Advancement of Materials and Process Engineering Symposium, J. Janicki, V. Bailey, and H. Schjelderup, eds., The Society for the Advancement of Materials and Process Engineering, Covina, Ca., pp. 1280–1291.