journal article·2009-07-01

A Method for Estimating Uncertainty of Indentation Tensile Properties in Instrumented Indentation Test

Eun-chae Jeon, Joo-Seung Park, Doo-Sun Choi, Kug-Hwan Kim, Dongil Kwon

Publisher page

Abstract

The instrumented indentation test, which measures indentation tensile properties, has attracted interest recently because this test can replace uniaxial tensile test. An international standard for instrumented indentation test has been recently legislated. However, the uncertainty of the indentation tensile properties has never been estimated. The indentation tensile properties cannot be obtained directly from experimental raw data as can the Brinell hardness, which makes estimation of the uncertainty difficult. The simplifying uncertainty estimation model for the indentation tensile properties proposed here overcomes this problem. Though the influence quantities are generally defined by experimental variances when estimating uncertainty, here they are obtained by calculation from indentation load-depth curves. This model was verified by round-robin test with several institutions. The average uncertainties were estimated as 18.9% and 9.8% for the indentation yield strength and indentation tensile strength, respectively. The values were independent of the materials’ mechanical properties but varied with environmental conditions such as experimental instruments and operators. The uncertainties for the indentation yield and tensile strengths were greater than those for the uniaxial tensile test. These larger uncertainties were caused by measuring local properties in the instrumented indentation test. The two tests had the same tendency to have smaller uncertainties for tensile strength than yield strength. These results suggest that the simplified model can be used to estimate the uncertainty in indentation tensile properties.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Advanced Surface Polishing Techniques · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Division of Nano-Mechanical Systems, Korea Institute of Machinery & Materials, Daejeon, 305-343, Korea

Technology & Standards Policy Division, Korea Agency for Technology and Standards, Gwacheon, 427-723, Korea

School of Materials Science and Engineering, Seoul National University, Seoul, 151-742, Korea

References (24)

Show source-provided references
1. Energy Principle of the Indentation-Induced Inelastic Surface Deformation and Hardness of Brittle Materials10.1016/0956-7151(93)90194-W ↗
2. Determining Brinell Hardness From Analysis of Indentation Load-Depth Curve Without Optical Measurement10.1115/1.1839213 ↗
3. A Method for Interpreting the Data From Depth-Sensing Indentation Instruments10.1557/JMR.1986.0601 ↗
4. An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments10.1557/JMR.1992.1564 ↗
5. Derivation of Plastic Stress-Strain Relationship From Ball Indentation: Examination of Strain Definition and Pileup Effect10.1557/JMR.2001.0437 ↗
6. Optimum Definition of True Strain Beneath a Spherical Indenter for Deriving Indentation Flow Curves10.1016/j.msea.2005.12.012 ↗
7. Continuous Measurements of Load Penetration Curves With Spherical Micro-Indenters and the Estimation of Mechanical Properties10.1557/JMR.1998.0197 ↗
8. Energy Dissipation, Fracture Toughness and the Indentation Load-Displacement Curve of Coated Materials10.1016/S0257-8972(00)00906-3 ↗
9. An Instrumented Indentation Technique for Estimating Fracture Toughness of Ductile Materials: A Critical Indentation Energy Model Based on Continuum Damage Mechanics10.1016/j.actamat.2005.10.033 ↗
10. Estimation of Biaxial Surface Stress by Instrumented Indentation With Sharp Indenters10.1016/j.actamat.2003.12.006 ↗
11. A New Method for Estimating Residual Stresses by Instrumented Sharp Indentation10.1016/S1359-6454(98)00226-2 ↗
12. 2002, “Metallic Materials—Instrumented Indentation Test for Indentation Tensile Properties,” Korean Standard B 0950, KSA, Seoul, Korea.
13. 2008, “Metallic Materials—Measurement of Mechanical Properties by Instrumented Indentation Test—Indentation Tensile Properties,” ISO/TR 29381, ISO, Geneva, Switzerland.
14. An International Round-Robin Experiment to Evaluate the Consistency of Nanoindentation Hardness Measurements of Thin Films10.1016/S0257-8972(02)00889-7 ↗
15. Nanoindentation Round Robin on Thin Film Copper on Silicon10.1007/s11661-007-9177-7 ↗
16. Determining Representative Stress and Representative Strain in Deriving Indentation Flow Curves Based on Finite Element Analysis10.4028/www.scientific.net/KEM.297-300.2152 ↗
17. Tabor · 2
18. Indentation Hardness and Hot Pressing10.1016/0001-6160(80)90166-2 ↗
20. 2008, “Uncertainty of Measurement—Part 3: Guide to the Expression of Uncertainty in Measurement,” ISO/IEC Guide 98–3, International Organization for Standardization, Geneva, Switzerland.
21. Adams
22. Chieh, C. J. , 2008, “Linear Regression: Making Sense of a Six Sigma Tool,” iSixSigma Europe, http://europe.isixsigma.com/library/content/c071212b.asp.
23. Loveday, M. S. , 1999, “Room Temperature Tensile Testing: A Method for Estimating Uncertainty of Measurement,” CMMT, National Physical Laboratory, Teddington, UK, http:/midas.npl.co.uk/midas/content/mn048.html.
24. Evaluation of the Uncertainty of Measurement of Mechanical Properties on the Tensile Testing