journal article·2005-01-01

Micromechanical Modeling of the Static Loading of an Al 359-SiC MMC

M. S. Bruzzi, P. E. McHugh

Publisher page

Abstract

The objective of this work was to use micromechanical finite element models to simulate the static mechanical behavior of a metal matrix composite: a cast Al 359 alloy reinforced with 20% SiC particles, at two different temperatures: room temperature and 150°C. In the simulations, periodic unit cell models incorporating the explicit representation of the matrix, reinforcing particles and precipitated primary silicon crystals in both 2D and 3D were used. Micromechanical models with both idealized and realistic reinforcing particle geometries and distributions were generated. The realistic particle geometries and distributions were inferred from experimental SEM micrographs. The pattern and intensity of the plastic deformation within the matrix was studied and the macroscale behavior of the composite was inferred from average stress and strain values. In order to include the effects of residual stresses due to the processing of the material, a quenching simulation was performed, prior to mechanical loading, and its effects on the macroscopic and microscopic behavior of the MMC was assessed. The effects of introducing the damage mechanisms of ductile void growth and brittle failure of the reinforcing particles was also investigated. The results of the simulations were compared with experimental results for the MMC in terms of macroscopic tensile stress–strain curves and conclusions were drawn.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Micromechanics Research Unit, Department of Mechanical Engineering, National University of Ireland, Galway, Ireland

References (36)

Show source-provided references
1. Forn, A., Martin, E., Baile, M. T., and Bastidas, J. M., 2002, “Corrosion Behavior of AA2124 and AA359 Reinforced with SiC Particles,” 15th International Corrosion Congress, Granada, Spain.
2. Forn, A., Martin, E., and Nogue, R., 2000, “Characterization and Mechanical Properties of 359+20%SiCp,” 8th National Con. Heat Treat. Surf., Barcelona, Spain.
3. Tabernig, B., and Pippan, R., 1998, Brite-Euram MISPOM Project Working Paper UPC/WP/2/3 dated 31 March 1998.
4. Fiori, F., Girardin, E., Giuliani, A., Lorentzen, T., Pyzalla, A., Rustichelli, F., and Stanic, V., 2000, “Neutron Diffraction Measurements For the Determination of Residual Stresses in MMC Tensile and Fatigue Specimens,” Physica B, 276–278, pp. 923–924.10.1016/S0921-4526(99)01592-6 ↗
5. Carrado, A., Fiori, F., Girardin, E., Pirling, T., Powell, P., and Rustichelli, F., 2001, “Neutron Diffraction Measurements of Residual Stresses in Metal Matrix Composite Samples,” Radiat. Phys. Chem., 61, pp. 575–577.10.1016/S0969-806X(01)00336-X ↗
6. Suresh, S., Mortensen, A., and Needleman, A., eds., 1993, Fundamentals of Metal Matrix Composites, Butterworth-Heinemann, Stoneham, MA.
7. Bo¨hm, H. J., 1998, “A Short Introduction to Basic Aspects of Continuum Mechanics,” CDL-FMD Report 3, Institute of Lightweight Structures and Aerospace Engineering, Vienna University of Technology, Austria.
8. Bo¨hm, H. J., 2003, “Introduction to Continuum Mechanics,” Course Notes For CISM Course on Mechanics of Microstructured Materials, CISM, Udine, Italy.
9. Llorca, J., 2003, “Deformation and Damage in Particle Reinforced Composites: Experiments and Models,” Course Notes For CISM Course on Mechanics of Microstructured Materials, CISM, Udine, Italy.10.1007/978-3-7091-2776-6_4 ↗
10. McHugh, P. E., Asaro, R. J., and Shih, C. F., 1993, “Computational Modeling of Metal Matrix Composite Materials—I. Isothermal Deformation Patterns in Ideal Microstructures,” Acta Metall. Mater., 41, pp. 1461–1476.10.1016/0956-7151(93)90255-Q ↗
11. Christman, T., Needleman, A., and Suresh, S., 1989, Acta Metall. Mater., 37, pp. 3029–3050.10.1016/0001-6160(89)90339-8 ↗
12. Bao, G., McMeeking, R. M., and Hutchinson, J. W., 1991, Acta Metall. Mater., 39, pp. 1871–1882.10.1016/0956-7151(91)90156-U ↗
13. Weissenbek, E., Bohm, H. J., and Rammerstorfer, F. G., 1994, “Micromechanical Investigations of Arrangement Effects in Particle Reinforced Metal Matrix Composites,” Comput. Mater. Sci., 3, pp. 263–278.10.1016/0927-0256(94)90141-4 ↗
14. Llorca, J., Suresh, S., and Needleman, A., 1992, “An Experimental and Numerical Study of Cyclic Deformation in Metal Matrix Composites,” Metall. Trans. A, 23A, pp. 919–934.10.1007/BF02675568 ↗
15. Bo¨hm, H. J., 1991, “Computer Based Micromechanical Investigations of the Thermomechanical Behavior of Metal Matrix Composites,” Fortschr.-Ber. VDI Reihe 18 Nr. 101. Du¨sseldorf: VDI-Verlag.
16. Bruzzi, M. S., McHugh, P. E., O’Rourke, F., and Linder, T., 2001, “Micromechanical Modeling of the Static and Cyclic Loading of an Al 2141—SiC MMC,” Int. J. Plast., 17, pp. 565–599.10.1016/S0749-6419(00)00063-2 ↗
17. Li, Y., and Ramesh, K. T., 1998, “Influence of Particle Volume Fraction, Shape, and Aspect Ratio on the Behavior of Particle-Reinforced Metal Matrix Composites at High Rates of Strain,” Acta Mater., 46, pp. 5633–5646.10.1016/S1359-6454(98)00250-X ↗
18. Fischmeister, H., and Karlsson, B., 1997, “Plastizita¨tseigenschaften Grob-zweiphasiger Werkstoffe,” Z. Metallkd., 68, pp. 311–327.10.1515/ijmr-1977-680501 ↗
19. Brockenbrough, J. R., and Suresh, S., 1990, “Plastic Deformation of Continuous Fibre-Reinforced Metal-Matrix Composites: Effects of Fibre Shape and Distribution,” Acta Metall. Mater., 24, pp. 325–330.10.1016/0956-716X(90)90264-H ↗
20. Li, M., Ghosh, S., Richmond, O., Weiland, H., and Rouns, T. N., 1999, “Three Dimensional Characterization and Modeling of Particle Reinforced Metal Matrix Composites, Part I: Quantative Description of Microstructural Morphology,” Mater. Sci. Eng., A, 265, pp. 153–173.10.1016/S0921-5093(98)01132-0 ↗
21. Ghosh, S., Lee, K. H., and Raghavan, P., 1996, “Two Scale Analysis of Heterogeneous Elastic-Plastic Materials With Asymptotic Homogenization and Voronoi Cell Finite Element Model,” Comput. Methods Appl. Mech. Eng., 132, pp. 63–116.10.1016/0045-7825(95)00974-4 ↗
22. Ghosh, S., and Moorthy, S., 1998, “Particle Fracture Simulation in Non-Uniform Microstructures of Metal-Matrix Composites,” Acta Mater., 46, pp. 965–982.10.1016/S1359-6454(97)00289-9 ↗
23. Gusev, A. A. , 1997, “Representative Volume Element Size for Elastic Composites: A Numerical Study,” J. Mech. Phys. Solids, 45, pp. 1449–1459.10.1016/S0022-5096(97)00016-1 ↗
24. Watt, D. F., Xu, X. Q., and Lloyd, D. J., 1996, “Effects of Particle Morphology and Spacing on the Strain Fields in a Plastically Deforming Matrix,” Acta Metall. Mater., 44, pp. 789–799.10.1016/1359-6454(95)00209-X ↗
25. Bo¨hm, H. J., Eckschlager, A., and Han, W., 2002, “Multi-Inclusion Unit Cell Models for Metal Matrix Composites With Randomly Oriented Discontinuous Reinforcements,” Comput. Mater. Sci., 25, pp. 42–53.10.1016/S0927-0256(02)00248-3 ↗
26. Bo¨hm, H. J., and Han, W., 2001, “Comparisons Between Three-Dimensional and Two-Dimensional Multi-Particle Unit Cell Models For Particle Reinforced Metal Matrix Composites,” Modell. Simul. Mater. Sci. Eng., 25, pp. 47–65.10.1088/0965-0393/9/2/301 ↗
27. Hine, P. J., Lusti, H. R., and Gusev, A. A., 2002, “The Numerical Simulation of the Elastic and Thermoelastic Properties of Short Fibre Composites,” Compos. Sci. Technol., 62, pp. 1445–1453.10.1016/S0266-3538(02)00089-1 ↗
28. Gall, K., Horstemeyer, M., McDowell, D. L., and Fan, J., 2000, “Finite Element of the Stress Distributions Near Damaged Si Particle Clusters in Cast Al–Si Alloys,” Mech. Mater., 32, pp. 277–301.10.1016/S0167-6636(00)00003-X ↗
29. Eckschlager, A., Han, W., and Bo¨hm, H. J., 2002, “A Unit Cell Model For Brittle Fracture of Particles Embedded in a Ductile Matrix,” Comput. Mater. Sci., 25, pp. 85–91.10.1016/S0927-0256(02)00252-5 ↗
30. Segurado, J., Gonzales, C., and Llorca, J., 2003, “A Numerical Investigation of the Effect of Particle Clustering on the Mechanical Properties of Composites,” Acta Mater., 51, pp. 2355–2369.10.1016/S1359-6454(03)00043-0 ↗
31. Llorca, J., and Segurado, J., 2004, “Three-Dimensional Multiparticle Cell Simulations of Deformation and Damage in Sphere-Reinforced Composites,” Mater. Sci. Eng., A, 365, pp. 267–274.10.1016/j.msea.2003.09.035 ↗
32. Gurson, A. L., 1975, “Plastic Flow and Fracture Behavior of Ductile Materials Incorporating Void Nucleation, Growth and Interaction,” Ph.D. Thesis, Division of Engineering, Brown University, Providence, RI.
33. Gurson, A. L. , 1977, “Continuum Theory of Ductile Rupture by Void Nucleation and Growth: Part I—Yield Criteria and Flow Rules For Porous Ductile Materials,” J. Eng. Mater. Technol., 99, pp. 2–15.10.1115/1.3443401 ↗
34. HKS, 1997, ABAQUS Theory Manual Version 5.7, Hibbit, Karlsson and Sorensen, Inc., Pawtucket, RI.
35. HKS, 2003, ABAQUS Users Manuals Version 6.4, Hibbit, Karlsson and Sorensen, Inc., Pawtucket, RI.
36. Tabernig, B., Pippan, R., Bruzzi, M., McHugh, P., Foulquier, J., Rapoport, A., Fedrigoni, G. P., Powell, P. M., Cook, R., Forn, A., Martin, E., Fiori, F., and Rustichelli, F., 2000, “Modeling of In-Service Fatigue Performance of Particle Reinforced Aluminum Alloys,” Fatigue 2000, EMAS, M. R. Bache, P. A. Blackmore, J. Draper, J. H. Edwards, P. Roberts, J. R. Yates, eds., pp. 93–100.