Theoretical and Experimental Evaluation of the Bond Strength Under Peeling Loads
Source abstract
Abstract
Reliable applications of adhesively bonded joints require understanding of the stress distribution along the bond-line and the stresses that are responsible for the joint failure. To properly evaluate factors affecting peel strength, effects of defects such as voids on the stress distribution in the overlap region must be understood. In this work, the peel stress distribution in a single lap joint is derived using a strength of materials approach. The bonded joint is modeled as Euler-Bernoulli beams, bonded together with an adhesive, which is modeled as an elastic foundation which can resist both peel and shear stresses. It is found that for certain adhesive and adherend geometries and properties, a central void with the size up to 50 percent of the overlap length has negligible effect on the peak peel and shear stresses. To verify the solutions obtained from the model, the problem is solved again by using the finite element method and by treating the adherends and the adhesive as elastic materials. It is found that the model used in the analysis not only predicts the correct trend for the peel stress distribution but also gives rather surprisingly close results to that of the finite element analysis. It is also found that both shear and peel stresses can be responsible for the joint performance and when a void is introduced, both of these stresses can contribute to the joint failure as the void size increases. Acoustic emission activities of aluminum-adhesive-aluminum specimens with different void sizes were monitored. The AE ringdown counts and energy were very sensitive and decreased significantly with the void size. It was observed that the AE events were shifting towards the edge of the overlap where the maximum peeling and shearing stresses were occurring as the void size increased.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Mechanical Behavior of Composites · Structural Load-Bearing Analysis · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Industrial and Manufacturing Engineering, Northeastern University, Boston, MA 02115
References (25)
Show source-provided references
1. Schlickelmann R. J. , “Past, Present, and Future of Structural Adhesive Bonding in Aerospace Application,” Trans. JSCM, Vol. 5, No. 1–2. Dec. 1979.
2. Yurenka S. , “Peel Testing of Adhesive Bonded Metal,” J. of Applied Polymer Science, Vol. 4, Issue No. 20, pp. 136–144, 1962.10.1002/app.1962.070062004 ↗
3. Erdogan F. , and RatwaniM., “Stress Distribution in Bonded Joints,” J. of Composite Materials, Vol. 5, pp. 378–393, 1971.10.1177/002199837100500308 ↗
4. Goland M. , and Reissner, “The Stresses in Cemented Joints,” ASME Journal of Applied Mechanics, Vol. 1, No. 1, pp. A.17-A.27A.17-A.27, 1944.10.1115/1.4009336 ↗
5. Erdogan F. , and CivelekM. B., “Contact Problem for an Elastic Reinforcement Bonded to an Elastic Plate,” ASME Journal of Applied Mechanics, Vol. 41, pp. 1014–1018, 1974.
6. Delale F. , ErdoganF., and AydinogluM. N., “Stresses in Adhesively Bonded Joints: A Closed Form Solution,” J. of Composite Materials, Vol. 15, May 1981, p. 249249.10.1177/002199838101500305 ↗
7. Delale, F., and Erdogan, F., “Viscoelastic Analysis of Adhesively Bonded Joints,” NASA Contractor Properties, Part Performance, and Process Simulation, ASME 1991.
8. Rossettos J. N. , LinP., and Nayeb-HashemiH., “Comparison of the Effects of Debonds and Voids on Adhesive Joints,” ASME JOURNAL OF ENGINEERING MATERIALS TECHNOLOGY, Vol. 116, pp. 533–538. 1994.10.1115/1.2904324 ↗
9. Nayeb-Hashemi, H., and Rossettos, J. N., “Nondestructive Evaluation of Adhesively Bonded Joints by Acousto-Ultrasonic Technique and Acoustic Emission,” J. of Acoustic Emission, Vol. 12, Nos. 1/2, 1994.10.1520/STP18134S ↗
10. Williams J. H. , and LeeS., “Acoustic Emission Monitoring of Fiber Composite Materials and Structures,” J. of Composite Materials, Vol. 12, Oct. 1978, pp. 348348.10.1177/002199837801200402 ↗
11. Williams, J. H., Lee, S., and Wang, T. K., “Nondestructive Evaluation of Strength and Separation Modes in Adhesively Bonded Automative Glass Fiber Composites Single Lap Joints,” J. of Composite Materials, Vol. 21, Jan. 1987.10.1177/002199838702100102 ↗
12. Williams J. H. , LeeS., and WangT. K., “Quantitative Nondestructive Evaluation of Automative Glass Fiber Composites,” J. of Comp. Materials, Vol. 16, pp. 20–39, Jan. 1982.10.1177/002199838201600102 ↗
13. Williams J. H. , and LeeS., “Acoustic Emission/Rupture Load Characterizations of Double-Braided Nylon Rope,” Marine Technology, Vol. 19, No. 3, pp. 268–271, July 1982.10.5957/mt1.1982.19.3.268 ↗
14. Williams J. H. , and LeeS., “Acoustic Emission Characterization Using AE [Parameter] Delay,” Materials Evaluation, Vol. 41, No. 8, pp. 961–966, July 1983.
15. Nayeb-Hashemi, H., and Jawad, Oussama, “Application of Acousto-Ultrasonic Technique and Acoustic Emission in Evaluation of Bond Strength,” PVP-Vol. 295/NE-Vol. 16, Recent Advances in Structural Mechanics, ASME 1994.
16. Hart-Smith, J., “Analysis and Design of Advanced Composite Bonded Joints,” NASA CR-2218, 1973.
17. Blichfeldt, B., and McCarthy, J. E., “Analytical and Experimental Investigation of Aircraft Metal Structures Reinforced with Filamentary Composites,” NASA CR-2039, 1972.
18. Ishai O. , and GirshengornT., “Strength of Bonded Aluminum-CFRP Single Lap Joints,” Adhesive Age, Vol. 21(7), pp. 25–30, 1978.
19. Hart-Smith, L. J., “Designing Adhesive Bonds,” Adhesive Age, pp. 32, Oct. 1978.
20. Crocombe A. D. , and AdamsR. D., “Peel Analysis Using the Finite Element Method,” J. Adhesion, Vol. 12, pp. 127–139, 1981.10.1080/00218468108071194 ↗
21. Olia, M., “Adhesively Bonded Joints,” Ph.D thesis. Department of Mechanical Engineering, Northeastern University, Boston MA 02115.
22. Curtis G. J. , “Acoustic Emission Energy Relates to Bond Strength,” Nondestructive Testing, Vol. 8, No. 5, pp. 249–257, Oct. 1975.10.1016/0029-1021(75)90045-6 ↗
23. Hill R. , “The Use of Acoustic Emission for Characterizing Adhesive Joint Failure,” NDT International, Vol. 10, No. 2, pp. 63–72, Apr. 1977.10.1016/0308-9126(77)90080-3 ↗
24. ASTM E976–94. “Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response,” ASTM, Philadelphia, PA 19103.
25. Nayeb-Hashemi, H., Rossettos, J. N., and Melo, A. P., “Multiaxial Fatigue Life Evaluation of Tubular Adhesively Bonded Joints,” Accepted and will appear in the Int. J. Adhesion and Adhesives, Vol. 17, 1997.10.1016/S0143-7496(96)00023-1 ↗