journal article·1995-01-01

Thermomechanical Fatigue Behavior of a Quasi-lsotropic SCS-6/Ti-15-3 Metal Matrix Composite

K. A. Hart, S. Mall

Publisher page

Abstract

The response of a quasi-isotropic laminate of metal matrix composite, SCS-6/Ti-15-3 in a thermomechanical fatigue (TMF) environment was investigated. To achieve this, three sets of fatigue tests were conducted: 1) in-phase TMF (IP-TMF), 2) out-of-phase TMF (OP-TMF), and 3) isothermal fatigue (IF). The fatigue response was dependent on the test condition and the maximum stress level during cycling. The IF, IP-TMF, and OP-TMF conditions yielded shortest fatigue life at higher, intermediate and lower stress levels, respectively. Examination of the failure mode through the variation of strain or modulus during cycling, and post-mortem microscopic evaluation revealed that it was dependent on the fatigue condition and applied stress level. Higher stresses, mostly with IP-TMF and IF conditions, produced a primarily fiber dominated failure. Lower stresses, mostly with the OP-TMF condition, produced a matrix dominated failure. Also, an empirical model based on the observed damage mechanisms was developed to represent the fatigue lives for the three conditions examined here.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Aluminum Alloys Composites Properties · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Aeronautics and Astronautics, Air Force Institute of Technology, Wright Patterson Air Force Base, OH 45433

References (19)

Show source-provided references
1. Pollock, W. D., and Johnson, W. S., “Characterization of Unnotched SCS-6/Ti-15–3 Metal Matrix Composites at 650°C,” Composite Testing and Design (Tenth Volume), ASTM STP 1120, 1992, pp. 175–191.10.1520/STP20154S ↗
2. Castelli, M. G., Ellis, J. R., and Bartolotta, P. A., “Thermomechanical Testing Techniques for High Temperature Composites: TMF Behavior of SiC (SCS6) Ti-15–3,” NASA Technical Memorandum 103171, 1990.
3. Mall S. , and ErmerP. G., “Thermal Fatigue Behavior of a Unidirectional SCS-6/Ti-15–3 Metal Matrix Composite,” Journal of Composite Materials, Vol. 25, 1991, pp. 1668–86.10.1177/002199839102501207 ↗
4. Gabb T. P. , GaydaJ. G., and MacKayR. A., “Isothermal and Nonisothermal Fatigue Behavior of a Metal Matrix Composite,” Journal of Composite Materials, Vol. 24, June 1990, pp. 667–686.10.1177/002199839002400605 ↗
5. Majumdar, B. S., and Newaz, G. M., “Thermomechanical Fatigue of an Angle-Ply Metal Matrix Composite,” Composite Materials: Fatigue and Fracture (Third Volume), ASTM STP 1110, 1991, pp. 732–752.10.1520/STP17746S ↗
6. Mall S. , and SchubbeJ. J., “Thermomechanical Fatigue Behavior of a Cross-Ply SCS-6/Ti-15–3 Metal Matrix Composite,” Composites Science and Technology, Vol. 50, 1994, pp. 49–57.10.1016/0266-3538(94)90125-2 ↗
7. Mall S. , and PortnerB., “Characterization of Fatigue Behavior in Cross Ply Laminate of SCS-6/Ti-15–3 Metal Matrix Composite at Elevated Temperature,” ASME JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY, Vol. 114, No. 4, Oct. 1992, pp. 409–415.10.1115/1.2904193 ↗
8. Russ S. M. , “Thermal Fatigue of Ti-24A1–11Nb/SCS-6,” Metall. Trans., Vol. 21A, 1990, pp. 1595–1602.10.1007/BF02672575 ↗
9. Brindley, P. K., MacKay, R. A., and Bartolotta, P. A., “Thermal Cycling and Isothermal Fatigue of SiC/Ti-24Al-11Nb,” HITEMP Review 1990, NASA Conf. Pub. 10051, 1990, pp. 38-1–38-12.
10. Russ, S. M., Nicholas, T., Bates, M., and Mall, S., “Thermomechanical Fatigue of SCS-6/Ti-24Al-11Nb Metal Matrix Composite,” Proc. of the ASME Symposium, Failure Mechanisms in High Temperature Composite Materials, AD-Vol. 22/AMD-Vol. 122, Dec. 1991, pp. 37–43.
11. Mall S. , NicholasT., HansonD. G., and RussS. M., “Thermomechanical Fatigue Behavior of a Cross-ply SCS-6/β21-S Metal Matrix Composite,”, Constitutive Behavior of High-Temperature Composites ASME MD-Vol. 40, 1992, pp. 91–106.
12. Johnson, W. S., Lubowinski, S. J., and Highsmith, A. L., “Mechanical Characterization of SCS-6/Ti-15-3 Metal Matrix Composites at Room Temperature,” Thermal and Mechanical Behavior of Ceramic and Metal Matrix Composites, ASTM STP 1080, 1990, pp. 193–218.10.1520/STP25401S ↗
13. Hart, K., “Behavior of a Quasi-Isotropic Ply Metal Matrix Composite Under Thermomechanical and Isothermal Fatigue Loading,” MS thesis, AFIT/GAE/ENY/92D-05, School of Engineering, Air Force Institute of Technology (AU), Wright-Patterson AFB OH, Dec. 1992.
14. Majumdar B. S. , and NewazG. M., “Inelastic Deformation in Metal Matrix Composites: Plasticity and Damage Mechanisms,” Philosophical Magazine, Vol. 66, No. 2, 1992, pp. 187–212.10.1080/01418619208201551 ↗
15. Robertson D. D. , and MallS., “Micromechanical Relations for Fiber-Reinforced Composites Using the Free Transverse Shear Approach,” Journal of Composite Technology and Research, Vol. 15, No. 3, 1993, pp. 181–192.10.1520/CTR10368J ↗
16. Bates, Mark A., “Thermo-Mechanical Fatigue of a Fiber Reinforced Titanium Aluminide Composite,” MS thesis, AFIT/GAE/ENY-91S-1, School of Engineering, Air Force Institute of Technology (AU), Wright-Patterson AFB OH, Mar. 1991.
17. Hopkins, D. A., and Chamis, C. C, “A Unique Set of Micromechanics Equations for High Temperature Metal Matrix Composites,” NASA TM-87154, Nov. 1985.
18. Metal Matrix Composites Analyzer, METCAN, Version 3.0, User’s Guide, NASA Lewis Research Center, Cleveland, OH, Dec. 1989.
19. Sendeckyj, G. P., “Fitting Models to Composites Materials Fatigue Data,” Test Methods and Design Allowables for Fibrous Composites, ASTM STP 734, C. C. Chamis, ed., American Society for Testing and Materials, 1981, pp. 112–119.10.1520/STP29314S ↗