journal article·2022-07

Life cycle assessment of environmentally friendly initiatives for sustainable machining: A short review of current knowledge and a case study

Navneet Khanna, Jwalant Wadhwa, Anjali Pitroda, Prassan Shah, Julius Schoop, Murat Sarıkaya

Publisher page

Abstract

The establishment of energy and resource-efficient machining processes is key for achieving more sustainable production in the manufacturing industries. However, accomplishing the eco-efficiency goal for machining high-strength materials used in the automotive and aerospace industry is challenging, because a trade-off must be achieved between energy consumption and economical productivity. To address this challenge from an ecological perspective, this study focuses on a detailed literature review of Life Cycle Assessment (LCA) analysis made on machining processes considering the comparison of cutting fluid strategies. Along with this, the present study also provides an extensive elucidation regarding the steps required to analyze LCA. Besides, this study aim to analyze LCA analysis in machining processes, and present the case study about macro-level comparative LCA of turning in-house cast AXZ911/10SiC metal matrix composites (MMCs) for three levels of cutting speed (vc), longitudinal feed rate (f), and axial depth of cut (ap). Each condition was subjected to three different cutting fluid approaches i.e., Dry, Liquid Carbon Dioxide (LCO2), and Liquid Nitrogen (LN2). Streamlined LCA (SLCA) was performed for 18 environmental impact categories using the Ecochain Mobius platform, connected to ReCiPe midpoint (H) and normalized with World (H) method. The findings showed that for all the levels of ap and the same cutting strategy, the lower vc and lower f result in a higher environmental impact. The comparison of the cutting fluid approach in terms of their correspondent normalized impact score reveals that machining in the cryogenic environment of LN2 with higher vc and higher f is the most sustainable and economical approach.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Energy Efficiency and Management · Advanced Machining and Optimization Techniques · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (93)

Show source-provided references
1. Imperatives · 1987
2. Jonker · 2012
3. Zokaei · 2013
4. Comparison of four environmental assessment tools in Swedish manufacturing: a case study
5. E.U. JRC · 2010
6. Kurdve · Waste flow mapping: Handbook · 2017 · 1
7. Lean and clean value stream mapping
8. Bellgran · 2012
9. Hauschild · 2018
10. Environmental life-cycle assessment10.1007/BF02978949 ↗
11. Curran · 2006 · 1
12. Resource and environmental profile analysis: a life cycle environmental assessment for products and procedures10.1016/0195-9255(92)90020-X ↗
13. Heijungs · 1992
14. Steen · 1999
15. Comparison of life cycle assessment databases: a case study on building assessment10.1016/j.buildenv.2014.04.025 ↗
16. Thinkstep
17. Does it matter which Life Cycle Assessment (LCA) tool you choose? – a comparative assessment of SimaPro and GaBi10.1016/j.jclepro.2014.08.004 ↗
18. Background for spatial differentiation in life cycle impact assessment
19. A technical framework for life-cycle assessments: workshop report, Washington, DC
20. A conceptual framework for life-cycle impact assessment
21. I.S. Organization · 1997
22. I.O. for Standardization · 2006
23. Transitioning to sustainable production – part II : evaluation of sustainable machining technologies10.1016/j.jclepro.2010.01.015 ↗
24. Cooling techniques to improve the machinability and sustainability of light-weight alloys: a state-of-the-art review10.1016/j.jmapro.2020.12.013 ↗
25. Sustainable milling of Ti-6Al-4V: a trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment
26. Ecological, economical and technological perspectives based sustainability assessment in hybrid-cooling assisted machining of Ti-6Al-4 V alloy
27. Investigation of hard turning performance of eco-friendly cooling strategies: cryogenic cooling and nanofluid based MQL10.1016/j.triboint.2019.106127 ↗
28. An approach to cleaner production for machining hardened steel using different cooling-lubrication conditions10.1016/j.jclepro.2018.03.279 ↗
29. Investigation into the surface quality and stress corrosion cracking resistance of AISI 316L stainless steel via precision end-milling operation10.1007/s00170-020-06413-4 ↗
30. Evaluation of modified 316L surface properties through HAp suspended EDM process for biomedical application10.1016/j.surfin.2021.101600 ↗
31. Application of environmentally-friendly cooling/lubrication strategies for turning magnesium/SiC MMCs
32. Machinability investigations on CFRP composites: a comparison between sustainable cooling conditions10.1007/s00170-021-07073-8 ↗
33. An extensive review of the water consumption and cutting fluid based sustainability concerns in the metal cutting sector10.1016/j.jclepro.2018.06.190 ↗
34. Environmental friendly cutting fluids and cooling techniques in machining: a review10.1016/j.jclepro.2014.07.071 ↗
35. Dry machining: a step towards sustainable machining – challenges and future directions10.1016/j.jclepro.2017.07.235 ↗
36. Analysis of cutting parameters and cooling/lubrication methods for sustainable machining in turning of Haynes 25 superalloy10.1016/j.jclepro.2016.05.122 ↗
37. Progress for sustainability in the mist assisted cooling techniques: a critical review10.1007/s00170-020-05529-x ↗
38. Environment and economic burden of sustainable cooling/lubrication methods in machining of Inconel-800
39. Comprehensive analysis of tool wear, tool life, surface roughness, costing and carbon emissions in turning Ti–6Al–4V titanium alloy: cryogenic versus wet machining
40. Evaluation of tool wear, surface roughness/topography and chip morphology when machining of Ni-based alloy 625 under MQL, cryogenic cooling and CryoMQL
41. Singh · 2019 · 12 · 1907
42. Investigation of surface integrity induced on AZ31C magnesium alloy turned under cryogenic and dry conditions10.1016/j.promfg.2019.09.035 ↗
43. Effect of cryogenic cooling on the heat transfer during turning of AZ31C magnesium alloy10.1080/01457632.2018.1450345 ↗
44. Effects of hot extrusion on microstructure and mechanical properties of Mg matrix composite reinforced with deformable TC4 particles10.1016/j.jma.2019.05.015 ↗
45. Numerical investigations of cutting temperature and cutting forces in cryogenic assisted turning of magnesium alloy10.1007/s00170-021-06989-5 ↗
46. Fiksel · 1996
47. Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes10.1016/S0924-0136(00)00794-9 ↗
48. Dry machining and minimum quantity lubrication10.1016/S0007-8506(07)60027-4 ↗
49. The influence of tool coatings in machining of magnesium10.1016/S0257-8972(97)00505-7 ↗
50. Cooling capability of liquid nitrogen and carbon dioxide in cryogenic milling10.1016/j.cirp.2019.03.016 ↗
51. Chetan, comparative analysis of dry, flood, MQL and cryogenic CO2 techniques during the machining of 15-5-PH SS alloy10.1016/j.triboint.2020.106196 ↗
52. Sustainable machining of high temperature nickel alloy – Inconel 718: part 1 – predictive performance models10.1016/j.jclepro.2014.06.040 ↗
53. Measurement and evaluation of hole attributes for drilling CFRP composites using an indigenously developed cryogenic machining facility
54. Tool wear and hole quality evaluation in cryogenic Drilling of Inconel 718 superalloy
55. Comprehensive machining analysis to establish cryogenic LN2 and LCO2 as sustainable cooling and lubrication techniques10.1016/j.triboint.2020.106314 ↗
56. Sustainability and machinability improvement of Nimonic-90 using indigenously developed green hybrid machining technology10.1016/j.jclepro.2020.121402 ↗
57. Evaluation of tool Wear, energy consumption, and surface roughness during turning of Inconel 718 using sustainable machining technique10.1016/j.jmrt.2020.03.104 ↗
58. Inconel 718 machining performance evaluation using indigenously developed hybrid machining facilities: experimental investigation and sustainability assessment10.1007/s00170-020-04921-x ↗
59. Resource efficiency analysis of lubricating strategies for machining processes using life cycle assessment methodology10.1016/j.jclepro.2019.03.073 ↗
60. On the concurrent optimization of environmental and economic targets for machining10.1016/j.jclepro.2018.04.163 ↗
61. Sustainability in wire electrical discharge machining of titanium alloy: understanding wire rupture10.1016/j.jclepro.2018.07.045 ↗
62. Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel10.1007/s00170-019-04325-6 ↗
63. Energy consumption model and energy efficiency of machine tools: a comprehensive literature review10.1016/j.jclepro.2015.05.093 ↗
64. Sustainability assessment during machining Ti-6Al-4V with Nano-additives-based minimum quantity lubrication
65. Manufacturing strategies for efficiency in energy and resources use: the role of metal shaping processes10.1016/j.jclepro.2016.10.182 ↗
66. Towards sustainability assessment of machining processes10.1016/j.jclepro.2017.09.197 ↗
67. Transitioning to sustainable production - part I: application on machining technologies10.1016/j.jclepro.2009.08.010 ↗
68. Comparison of life cycle emissions and energy consumption for environmentally adapted metalworking fluid systems10.1021/es800791z ↗
69. Quantitative analysis of carbon emissions of CNC-based machining systems
70. Life cycle assessment (LCA) applied to the process industry: a review10.1007/s11367-012-0432-9 ↗
71. Germani · 2016
72. Environmental burden analysis for machining operation using LCA method
73. Process level environmental performance of electrodischarge machining of aluminium (3003) and steel (AISI P20)10.1016/j.jclepro.2016.07.090 ↗
74. Cryogenic and minimum quantity lubrication for an eco-efficiency turning of AISI 30410.1016/j.jclepro.2016.08.030 ↗
75. Macro-level environmental comparison of near-dry machining and flood machining10.1016/j.jclepro.2010.01.017 ↗
76. Comparing environmental impacts of additive manufacturing vs traditional machining via life-cycle assessment10.1108/RPJ-07-2013-0067 ↗
77. Laser cutting of various materials: kerf width size analysis and life cycle assessment of cutting process10.1016/j.optlastec.2017.02.014 ↗
78. Evaluation of an environment-friendly turning process of Inconel 601 in dry conditions10.1016/j.jclepro.2020.121919 ↗
79. Singh · 2015
80. Using Jatropha oil based metalworking fluids in machining processes: A functional and ecological life cycle evaluation
81. Multi-objective optimization and life cycle assessment of eco-friendly cryogenic N2 assisted turning of Ti-6Al-4V10.1016/j.jclepro.2018.10.334 ↗
82. Machining characteristics based life cycle assessment in eco-benign turning of pure titanium alloy10.1016/j.jclepro.2019.119598 ↗
83. Process performance and life cycle assessment of friction drilling on dual-phase steel10.1016/j.jclepro.2018.12.250 ↗
84. Life cycle analysis of grinding: a case study of non-cylindrical computer numerical control grinding via a unit-process life cycle inventory approach10.1177/0954405412454102 ↗
85. Investigation into alternative cooling methods for achieving environmentally friendly machining process10.1016/j.procir.2015.02.184 ↗
86. Life cycle assessment of drilling Inconel 718 using cryogenic cutting fluids while considering sustainability parameters
87. Life cycle assessment: past, present, and future10.1021/es101316v ↗
88. Hischier · 2010
89. Jungbluth · 2020
90. Impact assessment methods in life cycle assessment and their impact categories
91. Cryogenic turning of in-house cast magnesium based MMCs: a comprehensive investigation10.1016/j.jmrt.2020.05.023 ↗
92. Environmental modelling of aluminium based components manufacturing routes: additive manufacturing versus machining versus forming10.1016/j.jclepro.2017.12.115 ↗
93. Risks related to the lack of lubrication on surface integrity in drilling10.1016/j.heliyon.2019.e01138 ↗