3D printable silicone compositions exhibiting high toughness and low durometer
Source abstract
Abstract
3D printable silicones can be designed with varying crosslink density, network structures, and types of reinforcing additives. Within this design space, one may tailor the uncured material’s rheology and mechanical response to access a wide range of potential applications. However, printable, low modulus silicones, particularly those applicable to direct ink write, are underreported in published literature. To address the need for higher performance, low modulus silicones with demonstrated printability, a new set of ca. 20–50 Shore A hardness silicone elastomers exhibiting ca. 7 MPa ultimate tensile strength and ca. 400–1200% elongation at break is presented. Mechanical properties were analyzed, providing insight to the effects of formulation constituents on mechanical properties. Cyclic mechanical testing of the silicone formulations was also performed, and the energy loss and permanent set throughout cycling were determined. Printed structures demonstrate the feasibility of these new silicones as durable frameworks for novel soft device applications.Graphical abstract(a) The anatomy of a formulation is influenced by properties of the base polymer as well as filler. The print fidelity of a structure is highly dependent on good formulation development; (b) Dow Silastic NPC-9300 yields a poorly developed print that does not retain threedimensional structure whereas (c) Dow SE-1700, a formulation that exhibits requisite thixotropy for AM, will maintain its structure under gravity. (d) New formulations presented herein have improved mechanical properties in addition to good print resolution, setting the benchmark for a new class of high strength DIW printable silicone elastomers.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Advanced Sensor and Energy Harvesting Materials · Manufacturing Process and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. A. Pagoli, F. Chapelle, J.A. Corrales-Ramon, Y. Mezouar, Y. Lapusta, Review of soft fluidic actuators: classification and materials modeling analysis. Smart Mater. Struct. 31(1), 013001 (2021)10.1088/1361-665X/ac383a ↗
2. V. Kumar, M.N. Alam, S.S. Park, Review of recent progress on silicone rubber composites for multifunctional sensor systems. Polymers 16(13), 1841 (2024)10.3390/polym16131841 ↗
3. M. Cianchetti, C. Laschi, A. Menciassi, P. Dario, Biomedical applications of soft robotics. Nat. Rev. Mater. 3(6), 143–153 (2018)10.1038/s41578-018-0022-y ↗
4. J.R.C. Dizon, A.D. Valino, L.R. Souza, A.H. Espera Jr., Q. Chen, R.C. Advincula, Three-dimensional-printed molds and materials for injection molding and rapid tooling applications. MRS Commun. 9(4), 1267–1283 (2019)10.1557/mrc.2019.147 ↗
5. D. Loaldi, L. Piccolo, E. Brown, G. Tosello, C. Shemelya, D. Masato, Hybrid process chain for the integration of direct ink writing and polymer injection molding. Micromachines 11(5), 509 (2020)10.3390/mi11050509 ↗
6. M. Kreiger, J.M. Pearce, Environmental life cycle analysis of distributed three-dimensional printing and conventional manufacturing of polymer products. ACS Sustain. Chem. Eng. 1(12), 1511–1519 (2013)10.1021/sc400093k ↗
7. Three‐Dimensional Printing of Elastomeric, Cellular Architectures with Negative Stiffness - Duoss - 2014 - Advanced Functional Materials - Wiley Online Library [Internet]. [cited 2024 Aug 16]. Available from: https://onlinelibrary.wiley.com/doi/full/https://doi.org/10.1002/adfm.20140045110.1002/adfm.201400451 ↗
8. Z. Qin, B.G. Compton, J.A. Lewis, M.J. Buehler, Structural optimization of 3D-printed synthetic spider webs for high strength. Nat. Commun. 6(1), 7038 (2015)10.1038/ncomms8038 ↗
9. A. Clausen, F. Wang, J.S. Jensen, O. Sigmund, J.A. Lewis, Topology optimized architectures with programmable poisson’s ratio over large deformations. Adv. Mater. 27(37), 5523–5527 (2015)10.1002/adma.201502485 ↗
10. R.L. Truby, J.A. Lewis, Printing soft matter in three dimensions. Nature 540(7633), 371–378 (2016)10.1038/nature21003 ↗
11. Controlled In Situ Foaming for Mechanical Responsiveness of Architected Foams - Golobic - 2023 - Advanced Engineering Materials - Wiley Online Library [Internet]. [cited 2024 Aug 16]. Available from: https://onlinelibrary.wiley.com/doi/full/https://doi.org/10.1002/adem.20230133510.1002/adem.202301335 ↗
12. I.M. Van Meerbeek, J.M. Lenhardt, W. Small, T.M. Bryson, E.B. Duoss, T.H. Weisgraber, Compressive properties of silicone bouligand structures. MRS Bull. 48(4), 325–331 (2023)10.1557/s43577-022-00398-z ↗
13. A. Maiti, W. Small, J.P. Lewicki, T.H. Weisgraber, E.B. Duoss, S.C. Chinn et al., 3D printed cellular solid outperforms traditional stochastic foam in long-term mechanical response. Sci. Rep. 6(1), 24871 (2016)10.1038/srep24871 ↗
14. Z. Ma, X. Zhang, H. Liu, S. Lu, L. Qin, G. Dong, Direct ink writing of reinforced polydimethylsiloxane elastomer composites for flexure sensors. J. Appl. Polym. Sci. 139(46), e53153 (2022)10.1002/app.53153 ↗
15. A. Renteria, V.H. Balcorta, C. Marquez, A.A. Rodriguez, I. Renteria-Marquez, J. Regis et al., Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors. Flex Print Electron. 7(1), 015001 (2022)10.1088/2058-8585/ac442e ↗
16. M. Schaffner, J.A. Faber, L. Pianegonda, P.A. Rühs, F. Coulter, A.R. Studart, 3D printing of robotic soft actuators with programmable bioinspired architectures. Nat. Commun. 9(1), 878 (2018)10.1038/s41467-018-03216-w ↗
17. Z.L. Yu, Q. Gao, F.J. Zhong, C.Q. Yong, Z.J. Pei, Y. Sun et al., Multimaterial 3D printing of highly stretchable silicone elastomers. ACS Appl. Mater. Interfaces 11(26), 23573–83 (2019)10.1021/acsami.9b04873 ↗
18. H. Satterfield, J. Beach, N. Pickering, S. Patterson, J.M. Messman, P.R. Dvornic, One-component, vinyl-functional fluorosilicone pastes for direct ink write additive manufacturing. Macromolecules 56(24), 10049–10066 (2023)10.1021/acs.macromol.3c01238 ↗
19. J.A. Armas, M.J. Ford, K.P. Foster, T. Hall, C.K. Loeb, S. Schmidt, et al. Electrostatic dissipation in 3D-printable silicone. ACS Appl. Mater. Interfaces [Internet]. 2024 Sep 3 [cited 2024 Sep 28]; Available from:https://doi.org/10.1021/acsami.4c0945510.1021/acsami.4c09455 ↗
20. M.M. Durban, J.M. Lenhardt, A.S. Wu, W. Small IV., T.M. Bryson, L. Perez-Perez et al., Custom 3D printable silicones with tunable stiffness. Macromol. Rapid Commun. 39(4), 1700563 (2018)10.1002/marc.201700563 ↗
21. J. Beach, S. Mann, C. Ault, D. Radojcic, X. Wan, A. Zlatanic et al., “All-in-One” thixotropic polysiloxane pastes for UV-activated room temperature hydrosilylation cross-linking in additive manufacturing. Macromolecules 54(4), 1715–1724 (2021)10.1021/acs.macromol.0c02457 ↗
22. S. de Gelidi, G. Tozzi, A. Bucchi, The role of pre-conditioning frequency in the experimental characterization of hyper-elastic materials as models for soft tissue applications. Int. J. Appl. Mech. 08(05), 1650066 (2016)10.1142/S1758825116500666 ↗
23. S. Xu, D.M. Vogt, W.H. Hsu, J. Osborne, T. Walsh, J.R. Foster et al., Biocompatible soft fluidic strain and force sensors for wearable devices. Adv. Funct. Mater. 29(7), 1807058 (2019)10.1002/adfm.201807058 ↗
24. S. Cantournet, R. Desmorat, J. Besson, Mullins effect and cyclic stress softening of filled elastomers by internal sliding and friction thermodynamics model. Int. J. Solids Struct. 46(11), 2255–2264 (2009)10.1016/j.ijsolstr.2008.12.025 ↗
25. B. Yin, H. Wen, W. Luo, M. Li, Frequency- and temperature-dependent Payne effect and hysteresis loss of carbon black filled rubbers: experimental study and model prediction. Mater. Today Commun. 1(33), 104920 (2022)10.1016/j.mtcomm.2022.104920 ↗
26. N. Warasitthinon, A.C. Genix, M. Sztucki, J. Oberdisse, C.G. Robertson, The payne effect: primarily polymer-related or filler-related phenomenon? Rubber Chem. Technol. 92(4), 599–611 (2019)10.5254/rct.19.80441 ↗
27. J. Diani, M. Brieu, K. Batzler, P. Zerlauth, Effect of the Mullins softening on mode I fracture of carbon-black filled rubbers. Int. J. Fract. 194(1), 11–18 (2015)10.1007/s10704-015-0030-5 ↗
28. V. Allen, L. Chen, M. Englert, A. Moussaoui, W. Pisula, Control of Mullins stress softening in silicone elastomer composites by rational design of fumed silica fillers. Compos. Sci. Technol. 29(214), 108955 (2021)10.1016/j.compscitech.2021.108955 ↗
29. J. Diani, B. Fayolle, P. Gilormini, A review on the Mullins effect. Eur. Polym. J. 45(3), 601–612 (2009)10.1016/j.eurpolymj.2008.11.017 ↗
30. J.M. Lenhardt. Llama 20, 40, 50 and 60 siloxanes for direct ink write – compositional information [Internet]. lawrence livermore national lab. (LLNL), Livermore, CA (United States); 2022 Jun [cited 2024 Aug 16]. Report No.: LLNL-TR-835928. Available from: https://www.osti.gov/biblio/187138110.2172/1871381 ↗
31. D.A. Rau, M.J. Bortner, C.B. Williams, A rheology roadmap for evaluating the printability of material extrusion inks. Addit. Manuf. 5(75), 103745 (2023)
32. H. Sun, W. Tian, Y. Sun, M. Li, 3D-printed mesh membranes with controllable wetting state for directional droplet transportation. Colloids Surf Physicochem. Eng. Asp. 5(638), 128143 (2022)10.1016/j.colsurfa.2021.128143 ↗
33. Z. Wang, C. Luan, Y. Zhu, G. Liao, J. Liu, X. Li et al., Integrated and shape-adaptable multifunctional flexible triboelectric nanogenerators using coaxial direct ink writing 3D printing. Nano. Energy 1(90), 106534 (2021)10.1016/j.nanoen.2021.106534 ↗
34. L.E. Govaert, H.G.H. van Melick, H.E.H. Meijer, Temporary toughening of polystyrene through mechanical pre-conditioning. Polymer 42(3), 1271–1274 (2001)10.1016/S0032-3861(00)00477-8 ↗
35. T. Scheffer, H. Seibert, S. Diebels, Optimisation of a pretreatment method to reach the basic elasticity of filled rubber materials. Arch. Appl. Mech. 83(11), 1659–1678 (2013)10.1007/s00419-013-0771-4 ↗
36. D. Zhong, Y. Xiang, T. Yin, H. Yu, S. Qu, W. Yang, A physically-based damage model for soft elastomeric materials with anisotropic Mullins effect. Int. J. Solids Struct. 30(176–177), 121–134 (2019)10.1016/j.ijsolstr.2019.05.018 ↗