Mixed oxides CuO-NiO fabricated for selective detection of 2-Aminophenol by electrochemical approach
Source abstract
Abstract
New heterometallic complex [NiCu(NO3)2(H2O)2] (1) was prepared via the reaction of aqueous solutions of (oxalic acid, nickel nitrate and copper nitrate). Mixed oxide CuO-NiO was successfully obtained with different morphological structures (2) and (3) through the annealing of 1 at different temperature 300 °C and 600 °C, respectively. The materials were characterized using FT-IR, TGA, XRD and SEM. As showed from XRD data, with increasing the calcination temperature the crystallinity of CuO-NiO in sample 3 was improved and the diffraction peaks exhibited narrower and stronger than CuO-NiO in sample 2. The average size of CuO-NiO crystals obtained was calculated from Debye-Scherrer equation and found to be 16.65 nm. To assemble the working electrode of 2-aminophenol (2-AP) chemical sensor, a thin layer of CuO-NiO NPs was deposited on glassy carbon electrode (GCE) with conducting binder and used to detect 2-AP in aqueous medium successfully. The chemical sensor is exhibited the higher stability, good sensitivity (20.2729 μAmM−1 cm−2) and enhanced electrochemical activity at room conditions. Therefore, the fabricated chemical sensor with active CuO-NiO NPs may be an effective and sensitive sensor for detection of hazardous materials by reliable I–V method for broad scales environmental safety of and healthcare sectors.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Electrochemical sensors and biosensors · Electrochemical Analysis and Applications · Analytical Chemistry and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (72)
Show source-provided references
1. The behavior of mixed-metal oxides: structural and electronic properties of Ce1−xCaxO2 and Ce1−xCaxO2−x10.1063/1.1601595 ↗
2. Structural and photoelectrocatalytic characteristic of ZnO/ZnWO4/WO3nanocomposites with double heterojunctions10.1016/j.physe.2010.09.005 ↗
3. Enhanced photoluminescence and photocatalytic activity of ZnO-ZnWO4 nanocomposites synthesized by a precipitation method10.1016/j.ceramint.2016.05.098 ↗
4. Label-free Kanamycin sensor development based on CuO NiO hollow-spheres: food samples analyses10.1016/j.snb.2018.02.173 ↗
5. Optical, magnetic, electrical, and chemo-catalytic properties of bio-synthesized CuO/NiO nanocomposites10.1016/j.jpcs.2019.109155 ↗
6. Nickel cuprate supported on cordierite as an active catalyst for CO oxidation by O210.1016/j.apcatb.2005.10.001 ↗
7. Characterization of NiAl and NiCuAl catalysts prepared by different methods for hydrogen production by thermo catalytic decomposition of methane10.1016/j.cattod.2006.05.071 ↗
8. Screening of metal oxide catalysts for carbon nanotubes and hydrogen production10.1016/S0167-2991(06)81699-X ↗
9. A facile design of nucleocapsid-like Au@NiO@CuO nanocomposites with MWCNT for glucose sensing10.1016/j.jelechem.2019.03.078 ↗
10. Enhanced open-circuit photovoltage and charge collection realized in pearl-like NiO/CuO composite nanowires based p-type dye sensitized solar cells10.1016/j.materresbull.2019.04.025 ↗
11. Nickel catalyst prepared via glycine nitrate process for partial oxidation of methane to syngas10.1016/j.catcom.2007.12.009 ↗
12. Fabrication of bipolar nickel metal hydride batteries with nanometer copper oxide as anodic additive10.1016/j.electacta.2006.02.020 ↗
13. Au anchored three-dimensional macroporous NiO@CuO inverse opals for in-situ sensing of hydrogen peroxide secretion from living cells10.1016/j.snb.2019.126729 ↗
14. Synthesis of NiO@CuO nanocomposite as high-performance gassensing material for NO2 at room temperature10.1016/j.apsusc.2017.03.213 ↗
15. Nickel oxide/hydroxide nanoplatelets synthesized by chemical precipitation for electrochemical capacitors10.1016/j.electacta.2007.12.005 ↗
16. Catalysis and the nature of mixed-metal oxides at the nanometer level: special properties of MO(x)/TiO(2)(110) {M = V, W, Ce} surfaces10.1039/c003665j ↗
17. The role of method of preparation of CuO–NiO system on its physicochemical surface and catalytic properties10.1016/j.colsurfa.2007.06.014 ↗
18. Physicochemical, surface and catalyic properties of nanocrystalline CuO–NiO system as being influenced by doping with La2O310.1016/j.colsurfa.2009.04.050 ↗
19. Synthesis and characterization of pure and ZrO2-doped nanocrystalline CuO–NiO system10.1016/j.apsusc.2007.07.132 ↗
20. Synthesis of CuO@NiO core-shell nanoparticles by homogeneous precipitation method10.1016/j.jallcom.2012.05.086 ↗
21. Synthesis and characterization of nano CuO-NiO mixed oxides10.13189/nn.2014.020103 ↗
22. Characterisation of the active sites in mixed oxides derived from LDH precursors by physico-chemical and catalytic techniques10.1016/j.apcata.2008.08.005 ↗
23. Methane partial oxidation on NiCu-based catalysts10.1016/j.cattod.2008.04.019 ↗
24. Liquid phase selective hydrogenation of citral over bimetallic transition metal catalysts
25. Highly sensitive nonenzymatic glucose sensor based on electrospun copper oxide-doped nickel oxide composite microfibers10.1016/j.talanta.2011.09.003 ↗
26. Humidity sensing properties of CuO, ZnO and NiO composites
27. N-alkylation of ethylenediamine with alcohols catalyzed by CuO-NiO/γ-Al2O310.2478/s11696-012-0140-8 ↗
28. Research on the N-alkylation of morpholine with alcohols catalyzed by CuO–NiO/γ–Al2O310.1007/s11144-011-0325-0 ↗
29. New nickel catalysts for the formation of filamentous carbon in the reaction of methane decomposition10.1006/jcat.1999.2562 ↗
30. In situ DRIFT study of low-temperature methanol synthesis mechanism on Cu/ZnO catalysts from CO2-containing syngas using ethanol promoter10.1016/j.jcat.2004.08.017 ↗
31. Annealing effects on the properties of copper oxide thin films prepared by chemical deposition10.1088/0268-1242/20/5/012 ↗
32. Systematic synthesis of mixed-metal oxides in NiO–Co3O4, NiO–MoO3, and NiO–CuO systems via liquid-feed flame spray pyrolysis10.1039/b801745j ↗
33. Influence of synthetic and processing parameters on the Surface Area, speciation, and particle formation in copper Oxide/Silica aerogel composites10.1021/cm021741x ↗
34. Cu–ZnO and Cu–ZnO/al2o3 catalysts for the reverse water-gas shift reaction. The effect of the Cu/Zn ratio on precursor characteristics and on the activity of the derived catalysts10.1023/A:1023592407825 ↗
35. Steam reforming of ethanol on Ni–CeO2–ZrO2 catalysts: effect of doping with copper, cobalt and calcium10.1007/s10562-007-9133-6 ↗
36. Ethanol sensor development based on ternarydoped metal oxides (CdO/ZnO/Yb2O3) nanosheets for environmental safety10.1039/C7RA01852E ↗
37. 3, 4-Diaminotoluene sensor development based on hydrothermally prepared MnCoxOy nanoparticles10.1016/j.talanta.2017.07.093 ↗
38. Treatment of phenol and cresols in up flow anaerobic sludge blanket (UASB) process: a review10.1016/j.watres.2004.07.028 ↗
39. Specific chemical reactivities of spatially separated 3-Aminophenol conformers with cold Ca+ ions10.1126/science.1242271 ↗
40. Contact anaphylaxis due to para-aminophenol and para-methylaminophenol in hair dye10.1034/j.1600-0536.2001.450610.x ↗
41. Oxidative DNA damage induced by a metabolite of carcinogenic o-anisidine: enhancement of DNA damage and alteration in its sequence specificity by superoxide10.1006/abbi.2001.2302 ↗
42. Polyelectrolyte functionalized gold nanoparticles-reduced graphene oxide nanohybrid for electrochemical determination of aminophenol isomers10.1016/j.electacta.2015.02.207 ↗
43. Simultaneous LC determination of paracetamol and related compounds in pharmaceutical formulations using a carbon-based column10.1016/S0731-7085(01)00515-5 ↗
44. Colorimetric determination of p-aminophenol in the presence of paracetamol with 3-cyano-Nmethoxypyridinium perchlorate10.1016/0039-9140(82)80121-5 ↗
45. Graphene–polyaniline composite film modified electrode for voltammetric determination of 4-aminophenol10.1016/j.snb.2011.05.053 ↗
46. Electrochemical behavior and voltammetric determination of 4-aminophenol based on graphene–chitosan composite film modified glassy carbon electrode10.1016/j.electacta.2010.06.072 ↗
47. A hemin-based molecularly imprinted polymer (MIP) grafted onto a glassy carbon electrode as a selective sensor for 4-aminophenol amperometric10.1016/j.snb.2010.12.010 ↗
48. Zinc oxide nanonail based chemical sensor for hydrazine detection10.1039/B711215G ↗
49. Phenolic sensor development based on chromium oxide-decorated carbon nanotubes for environmental safety10.1016/j.jenvman.2016.12.008 ↗
50. Fabrication of 4-aminophenol sensor based on hydrothermally prepared ZnO/Yb2O3 nanosheets10.1039/C7NJ01623A ↗
51. Cullity · 1967
52. A facile one-step route for production of CuO, NiO, and CuO–NiO nanoparticles and comparison of their catalytic activity for ammonium perchlorate decomposition10.1039/C5RA20155A ↗
53. Diaqua oxalato strontium(II) complex as a precursor for facile fabrication of Ag-NPs@SrCO3, characterization, optical properties, morphological studies and adsorption efficiency10.1080/00958972.2019.1588964 ↗
54. Antitumor and antimicrobial activities of novel palladacycles with abnormal aliphatic C-H activation of Schiff Base 2-[(3-phenylallylidene)amino] phenol10.1080/15533174.2013.831878 ↗
55. A novel heterometallic compound for design and study of electrical properties of silver nanoparticles-decorated lead compounds10.1039/C7NJ03682E ↗
56. Synthesis, characterization, corrosion inhibition of mild steel in HCl (0.5 N) solution and solid-state electrical conductivity of new Co(II), Ni(II), Cu(II) and Zn(II) complexes10.1002/aoc.3572 ↗
57. Synthesis and characterization of SrO, PbO, NiO nanoparticles and SnO2 microsphere via a PEG assisted route
58. Synthesis and comparative studies of cyclopalladated complexes with ortho C‒H activation of aromatic rings bearing electron donating and electron withdrawing groups10.1080/15533174.2013.862641 ↗
59. A novel photocatalytic system consists of Co(II) complex@ZnO exhibits potent antimicrobial activity and efficient solar-induced wastewater remediation10.1016/j.solener.2018.05.073 ↗
60. Surface modification of sulfonated poly(ether ether ketone) membranes using nafion solution for direct methanol fuel cells10.1016/j.memsci.2004.09.006 ↗
61. Electrochemical detection of trace cadmium in soilusing a Nafion/stannum film-modified molecular wire carbon paste electrodes10.1007/s11581-013-0891-4 ↗
62. Flexible graphene oxide-wrapped SnO2 hollow spheres with high electrochemical sensing performance in simultaneous determination of 4-aminophenol and 4-chlorophenol10.1016/j.electacta.2017.08.043 ↗
63. Highly sensitive and simultaneous electrochemical determination of 2-aminophenol and 4-aminophenol based on poly (L-arginine)-β-cyclodextrin/carbon nanotubes10.1016/j.bios.2015.09.052 ↗
64. Electrochemically pretreated screen-printed carbon electrodes for the simultaneous determination of aminophenol isomers10.1016/j.jelechem.2010.11.028 ↗
65. Facile green synthesis of graphene–titanium nitride hybrid nanostructure for the simultaneous determination of acetaminophen and 4-aminophenol10.1016/j.snb.2015.02.120 ↗
66. High-performance sensor based on copper oxide nanoparticles for dual detection of phenolic compounds and a pesticide Electrochemistry
67. Fabrication of phenyl-hydrazine chemical sensor based on Al-doped ZnO nanoparticles
68. Green material: ecological importance of imperative and sensitive chemi-sensor based on Ag/Ag2O3/ZnO composite nanorods10.1186/1556-276X-8-380 ↗
69. Polyelectrolyte functionalized gold nanoparticles-reduced graphene oxide nanohybrid for electrochemical determination of aminophenol isomer10.1016/j.electacta.2015.02.207 ↗
70. Fabrication of highly sensitive phenyl hydrazine chemical sensor based on as-grown ZnO-Fe2O3 microwire10.1016/S1452-3981(23)14038-7 ↗
71. High-performance sensor based on copper oxide nanoparticles for dual detection of phenolic compounds and a pesticide10.1016/j.elecom.2016.08.001 ↗
72. Graphene–polyaniline composite film modified electrode for voltammetric determination of 4-aminophenol10.1016/j.snb.2011.05.053 ↗