journal article·2022-07Open access

Effect of oscillating laser beam on the interface and mechanical properties of Ti/Al fusion welding joint

Jiafu Zhou, Dianwu Zhou, Jinshui Liu

Abstract

To solve the problem that cracks and brittle Ti-Al intermetallic compounds restrict the mechanical properties of Ti-Al joint, an effective connection method has been explored for laser welding of TC4 titanium alloy and 7075 aluminum alloy by oscillating laser beam, and the effect of oscillating laser beam on the interface and mechanical properties of Ti/Al fusion welding joint was also investigated. With the application of beam oscillation, some defects like pores and cracks can be avoided in welding joint, the connection width of interface layer is increased, and the diffusion of Al-to-Ti is suppressed due to the reduced interfacial heat input and the stirring effect induced by the keyhole rotating. As a result, Al-rich Ti-Al compound at interface is reduced while Ti-rich compound is formed. Generally, the property of Ti/Al joint can be significantly improved by the reduction of joint defects and the formation of lower brittle TiAl/Ti3Al compounds. As the oscillation frequency increase, the maximum load of the joint increases first but then decreases, and reached the highest value of 1852N when the 150 Hz oscillating frequency is applied, representing 76.38% enhancement compared with that without oscillation. However, under the condition of excessive oscillating frequency, the interface layer is too thin to form an effective connection, which deteriorates the joint properties.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Intermetallics and Advanced Alloy Properties · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Influence of vanadium filler on the properties of titanium and steel TIG welded joints10.1016/j.jmatprotec.2016.06.018 ↗
2. Fatigue in laser welded titanium tubes intended for use in aircraft pneumatic systems10.1016/j.ijfatigue.2016.04.018 ↗
3. Weld pool dynamics and joining mechanism in pulse wave laser beam welding of Ti-6Al-4V titanium alloy sheets assembled in butt joint with an air gap10.1016/j.optlastec.2021.107558 ↗
4. Development of ultrafine grained high strength age hardenable Al 7075 alloy by cryorolling10.1016/j.matdes.2011.02.051 ↗
5. Formability and microstructure evolution for hot gas forming of laser-welded TA15 titanium alloy tubes10.1016/j.matdes.2015.11.100 ↗
6. Welding and joining of NiTi shape memory alloys: a review10.1016/j.pmatsci.2017.04.008 ↗
7. An insight to the mechanism of weld penetration in dissimilar pulsed laser welding of niobium and Ti-6Al-4V10.1016/j.optlastec.2015.11.005 ↗
8. Influence of interfacial reaction layer morphologies on crack initiation and propagation in Ti/Al joint by laser welding-brazing10.1016/j.matdes.2009.06.029 ↗
9. Direct keyhole laser welding of aluminum alloy AA5754 to titanium alloy Ti6Al4V10.1016/j.jmatprotec.2014.10.025 ↗
10. Yb-YAG laser offset welding of AA5754 and T40 butt joint10.1016/j.jmatprotec.2015.04.003 ↗
11. Modeling and experimental analysis of fiber laser offset welding of Al-Ti butt joints10.1007/s00170-015-7562-8 ↗
12. Laser penetration welding of an overlap titanium-on-aluminum configuration10.1007/s00170-016-8732-z ↗
13. Investigation of welding crack in laser welding-brazing welded TC4/6061 and TC4/2024 dissimilar butt joints10.1016/j.jmapro.2020.10.029 ↗
14. Improving interfacial reaction nonhomogeneity during laser welding-brazing aluminum to titanium10.1016/j.matdes.2011.03.074 ↗
15. Aluminum to titanium laser welding-brazing in V-shaped groove10.1016/j.jmatprotec.2017.02.009 ↗
16. Low temperature heat treatments of AA5754-Ti6Al4V dissimilar laser welds: microstructure evolution and mechanical properties10.1016/j.optlastec.2017.09.039 ↗
17. Microstructure and tensile behavior of laser arc hybrid welded dissimilar Al and Ti alloys10.3390/ma7031590 ↗
18. Microstructure and tensile properties of Ti/Al dissimilar joint by laser welding-brazing at subatmospheric pressure10.1016/j.jmapro.2020.04.062 ↗
19. Influence of Si content on interfacial reactions and mechanical properties of dual-spot laser welded-brazed Ti/Al joints10.1016/j.jmapro.2020.06.001 ↗
20. Improving intermetallic compounds inhomogeneity of Ti/Al butt joints by dual laser-beam bilateral synchronous welding-brazing10.1016/j.optlastec.2021.107533 ↗
21. Effect of beam oscillating pattern on weld characterization of laser welding of AA6061-T6 aluminum alloy10.1016/j.matdes.2016.07.053 ↗
22. Interfacial microstructure and mechanical properties of laser-welded 6061Al/AISI304 dissimilar lap joints via beam oscillation10.1016/j.jmrt.2020.10.064 ↗
23. Optimization of the solidification conditions by means of beam oscillation during laser beam welding of aluminum10.1016/j.matdes.2018.11.009 ↗
24. A study on laser beam oscillating welding characteristics for the 5083 aluminum alloy: morphology, microstructure and mechanical properties10.1016/j.jmapro.2020.01.018 ↗
25. Analysis and improvement of laser wire filling welding process stability with beam wobble10.1016/j.optlastec.2020.106594 ↗
26. Processing modes in laser beam oscillating welding of Al6Cu alloy10.1016/j.jmapro.2021.06.049 ↗
27. Effects of beam oscillation on interface layer and mechanical properties of laser-arc hybrid lap welded Al/Mg dissimilar metals10.1016/j.intermet.2021.107175 ↗
28. First-principles calculation on the structural, elastic and thermodynamic properties of Ti-Al intermetallics10.1088/2053-1591/ab3e11 ↗
29. Charting the complete elastic properties of inorganic crystalline compounds10.1038/sdata.2015.9 ↗
30. First-principles calculations of binary Al compounds: enthalpies of formation and elastic properties